13B-75
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF114
STOREDEGR SOLENOID VALVE CIRCUIT
1.DEF: At minimum limit
2.DEF: At maximum limit
3.DEF: Inconsistency
4.DEF: Valve jammed
5.DEF: Valve clogged
NOTESPriority when dealing with a number of faults:
– DF113 Sensor supply voltage.
Special notes:
If fault DF114 is present: the engine is unstable and may even stall. Starting difficult or
even impossible when cold, smoke emissions and loss of performance possible. On
status 4.DEF, the level 1 warning light illuminates with the message Faulty injection
displayed on the instrument panel.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine running.
See Technical Note Wiring Diagrams of the vehicle concerned.
Check the connection and condition of the EGR valve connector, component code 169.
Check the connection and condition of connector B (brown 48-track) of the injection computer, component
code120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check for +12 V on connection 3FB2 of component 169.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation and continuity of the following connections:
–3GB between components 169 and 120,
–3FB2 between components 169 and 1337.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
DDCR_V44_DF114M/DDCR_V48_DF114M
13B-79
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF122
PRESENTPEDAL POTENTIOMETER GANG 2 SUPPLY VOLTAGECO.1: Open circuit or short circuit to +12 volts
CC.0: Short circuit to earth
NOTESSpecial notes:
If DF122, the idling speed is stuck at 1000 rpm, the engine performance is reduced to
75%, and the level 1 warning light illuminates along with the message Faulty
injection.
CC.0
NOTESNone.
Check the connection and condition of the 6-track connector of the pedal potentiometer.
Repair if necessary.
Check the connection and condition of the black 32-track connector A of the computer.
Repair if necessary.
Measure the resistance between tracks 2 and 6 of the pedal potentiometer.
Replace the pedal potentiometer if the resistance is not 2.85 kΩ +
2.05 Ω.
Disconnect computer connector A and the pedal potentiometer connector.
Check the insulation against earth of the connection on track F2 on computer connector A.
Repair if necessary.
DDCR_V44_DF122P/DDCR_V48_DF122P
13B-81
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF130
STOREDFLOW CAPACITY FUNCTION
NOTESSpecial notes:
If DF130, the engine may stop with the level 1 and 2 warning lights illuminated along
with the message Faulty injection.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine running.
Check the connection and condition of the of the fuel flow actuator connector (IMV), and repair it if necessary.
Measure the resistance between tracks 1 and 2 of the flow actuator.
Replace the flow actuator if the resistance is not 5.3 Ω ± 0.5 Ω at 20°C.
Check the connection and condition of the computer 48-track brown connector B.
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connection:
Computer connector B track M4 track 1 fuel flow actuator
Repair if necessary.
Check that there is fuel present in the tank and that it is correct. Run Test 13 Diesel fuel conformity check.
Run Test 1 Low pressure circuit check.
Run Test 6 High pressure system check.
Repair if necessary.
DDCR_V44_DF130M/DDCR_V48_DF130M
