2011 RENAULT SCENIC heating

13B-124V4 MR-372-J84-13B000$080.mif
13B
DDCR INJECTION
Vdiag No.: 44, 48
* RCH = passenger compartment heating resistor: TOOL STATE DIAGNOSTIC TOOL DESCRIPTION
ET001 + After ignition computer feed
ET003 Engine immobiliser
ET004 Air conditioning authorised.
ET006 Code programmed
ET008 EGR solenoid valve control
ET021 High speed fan assembly request
ET022 Low speed fan assembly request
ET023 Fast idle speed request
ET038 Engine
ET042 Cruise control/speed limiter
ET076 Starting
ET079 Air conditioning present
ET088 Compressor actuation request
ET405 Clutch pedal switch
ET415 Deactivation of cruise control/speed limiter
ET563 Flow capacity function.
ET111 RCH* number set
ET112 RCH* cut-off
ET703 Cruise control/speed limiter button
ET704 Brakecontact No 1
ET705 Brakecontact No 2
DIESEL INJECTION
Fault finding – Status summary table

13B-143V4 MR-372-J84-13B000$100.mif
13B
DDCR INJECTION
Vdiag No.: 44, 48
* Heat.: HeatingTool parameter DIAGNOSTIC TOOL DESCRIPTION
PR005 EGR valve opening setpoint
PR008 Rail pressure set point
PR009 Turbocharging pressure setpoint
PR010 Idle speed regulation setpoint
PR017 Fuel flow
PR073 Air flowmeter supply voltage
PR028 Pedal position (gang 1)
PR029 Pedal position (gang 2)
PR030 Accelerator pedal position
PR032 Inlet pressure
PR035 Atmospheric pressure
PR037 Refrigerant pressure
PR038 Rail pressure
PR051 EGR valve position feedbac
PR055 Engine speed
PR059 Inlet air temperature (invalid in K9K 728)
PR061 External air temperature
PR063 Fuel temperature
PR064 Coolant temperature
PR074 Battery voltage
PR077 EGR valve position sensor voltage
PR080 Rail pressure sensor voltage
PR081 Inlet temperature sensor voltage
PR088 Pedal potentiometer gang 2 voltage
PR089 Vehicle speed
PR125 Power absorbed by air conditioning compressor
PR127 Heat.* resistor maximum authorised power
PR130 Cruise control setpoint
PR132 Air flow
DIESEL INJECTION
Fault finding – Parameter summary table

13B-146V4 MR-372-J84-13B000$110.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
DDCR INJECTION
Vdiag No.: 44, 48
CLEARING
RZ001: fault memory.
This command is used to clear stored faults from the computer's memory.
RZ002: EGR adaptives.
Run this command only when replacing the EGR valve.
RZ004: Pressure regulation parameters.
Run this command when replacing all 4 injectors at once. It enables you to reset the injector adaptive programs.
RZ005: Programming.
This command lets you reinitialise the entire computer configuration according to the vehicle.
COMMANDS
LPG - FUEL CIRCUIT tab
AC010: High-pressure pump.
This command lets you listen for the operation of the high pressure pump.
AC005 to AC008: Injectors of cylinders 1 to 4.
These commands let you listen for the injector on the selected cylinder.
AC028: Static test.
This command activates fault finding for the EGR and high pressure pump circuits.
AC029: High-pressure circuit seal check.
This command lets you check the high pressure circuit sealing after a procedure has been carried out.
AC212: New pump chamber filling.
Use this command only after replacing the high pressure pump (see High pressure pump replacement in
Replacement of components). This command is used to activate the pump repriming sequence.
IGNITION - PREHEATING tab
AC001: Preheating unit.
This command actuates the preheating unit to test the heater plug supply.
EMISSION CONTROL - OBD tab
AC002: EGR solenoid valve.
This command lets you listen to the mechanical operation of the EGR valve.
AC028: Static test.
This command activates fault finding for the EGR and high pressure pump circuits.
TURBO - INLET AIR CIRCUIT tab
AC004: Turbocharging solenoid valve.
This command lets you listen for the operation of the turbocharging solenoid valve.