2011 RENAULT SCENIC ABS

13B-190
MR-372-J84-13B200$504.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET144
HIGH-SPEED FAN ASSEMBLY RELAY CONTROL
STATUS DEFINITIONACTIVE: This status indicates that the high-speed fan assembly relay is actuated.
INACTIVE: This status indicates that the high-speed fan assembly relay is not
actuated.
ACTIVE
When the coolant reaches 99°C, the diesel computer activates the high-speed fan
assembly relay and status ET144 becomes ACTIVE.
The relay then supplies the fan assembly and the cooling fan begins to turn.
Run command AC039 High-speed fan unit relay and visually check that the cooling
fan is turning. If this is not the case, carry out the following operations:
– check the condition of fuse FM15 (60A) and the motor relay R10,
– disconnect the fan unit relays, check their operation and the condition of the
connections,
– repair if necessary,
– check for a + 12 V on connection 49B of components 597 and 262, when the high-
speed relay is actuated.
Check the continuity and the absence of interference resistance on the following
connections:
–Connection codes 3JP and 49B between components 120, 957 and 262.
If the connection or connections are faulty and there is a repair method (see Technical
Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair), repair the
wiring, otherwise replace it.
INACTIVEIf the engine temperature is less than 99°C, the engine cooling fan cannot switch on
and the high-speed fan assembly relay should not be actuated.
Status ET144 becomes INACTIVE when the control relay and the engine cooling fan
are not supplied.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V18_ET144/EDC16_V1C_ET144/EDC16_V20_ET144

13B-194
MR-372-J84-13B200$540.mif
V13
13B
DIESEL INJECTION
Fault finding – Interpretation of statuses
ET405
CLUTCH PEDAL SWITCH
STATUS DEFINITION"Inactive": this status indicates that the switch is released.
"Active": this status indicates that the switch is pressed.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
The clutch pedal is present depending on the gearbox type.
ACTIVE and clutch
pedal released
INACTIVE and
clutch pedal
depressed
Check the condition and fitting of the clutch pedal switch,
Remove the clutch pedal switch and check that it is functioning correctly.
Continuity between
connectionsInsulation between
connections
Switch pressed (Clutch
pedal released)MAM and 86D
Switch released (Clutch
pedal depressed)MAM and 86D
Replace the switch if necessary.
Check the condition and fitting of the clutch pedal switch,
Check the continuity and the absence of interference resistance on connection 86D
between components 120 and 675.
If the connection or connections are defective and there is a repair method (see
Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Check for an earth on connection MAM of the clutch switch.
Repair if necessary.
Remove the clutch pedal switch and check that it is functioning correctly.
Continuity between
connectionsInsulation between
connections
Switch pressed (Clutch
pedal released)MAM and 86D
Switch released (Clutch
pedal depressed)MAM and 86D
Replace the clutch pedal switch if necessary.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET405/EDC16_V58_ET405/EDC16_V5C_ET405/EDC16_V18_ET405/EDC16_V1C_ET405/EDC16_V20_ET405 EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
MR-372-J84-13B200$540.mif

13B-195
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CRUISE CONTROL/SPEED LIMITER DEACTIVATION
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system operation
programming.
Note:
Cruise control can be activated when the vehicle speed exceeds 20 mph (30 km/h).
Status ET415 shows various factors that cause deactivation of the cruise control/speed limiter function, due to a
driver request or the external environment (eg. STATUS 1).
IMPORTANT:
Clear the fault memory by running command RZ007 Fault memory, to reset this status to WITHOUT.
NONE
This status is present on the diagnostic tool if:
the computer has been reinitialised,
the computer has been reprogrammed.
STATUS 1Traction control request
If the vehicle is fitted with a traction control system, the cruise control function is
deactivated every time the ABS computer calls for traction control.
Status ET415 becomes STATUS 1 when driving, with cruise control active (ET042:
Cruise control/Speed limiter: CRUISE CONTROL) and upon a traction control
request.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status ET415 becomes STATUS 1 without a traction control request (see38C, ABS).
STATUS 2Brake pedal depressed
The cruise control function is deactivated when the brake pedal is depressed.
Status ET415 becomes "STATUS 2" when driving with cruise control active (ET042
Cruise control/Speed limiter: CRUISE CONTROL) and the brake pedal is depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status ET415 becomes STATUS 2 without pressing the brake pedal, consult the
interpretation of statuses ET704 and ET705 Brake contact No 1 and No 2.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET415/EDC16_V58_ET415/EDC16_V5C_ET415/EDC16_V18_ET415/EDC16_V1C_ET415/EDC16_V20_ET415

13B-197
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 2
STATUS 5
Cruise control or speed limiter monitoring
This status appears when the vehicle brakes or decelerates sharply without the
injection computer receiving a signal indicating that the brake pedal switch has been
pressed.
If status ET415 is STATUS 5, refer to the interpretation of:
– of status ET042 Cruise control/speed limiter,
– of status ET703 Cruise control/speed limiter buttons,
– of status ET704 Brake contact no. 1,
– and status ET705 Brake contact No 2,
to test the cruise control/speed limiter system components and find the defective
component.
Also check the operation of the accelerator pedal, and check for any faults on the
diagnostic tool relating to this component. Deal with them if necessary.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status ET415 changes to "STATUS 5", deal with present faults or those stored in the
injection computer.
If the fault is still present, contact Techline.
STATUS 6Gear lever in neutral (manual gearbox) or the neutral position (automatic
gearbox)
Status ET415 becomes STATUS 6 when driving with cruise control active (ET042
"Cruise control/speed limiter": CRUISE CONTROL) and:
– If the driver puts the gear lever in neutral position on a manual gearbox without
declutching or,
– if the gear lever is in neutral on an automatic gearbox.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status ET415 becomes STATUS 6 without shifting the gear lever into neutral on a
manual gearbox without declutching, or into neutral on an automatic transmission, test
the ABS computer and check the configuration of the tyre size stored in the computer. If
the configuration is correct, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-199
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 4
STATUS 9
Vehicle speed monitoring
Status ET415 changes to STATUS 9 if the vehicle speed received by the computer is
invalid or absent.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then Perform fault finding on the ABS computer.
Deal with any present or stored faults (see 38C, Anti-lock braking system,
interpretation of faults).
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status 9 continues, contact the Techline.
STATUS 10Monitoring by injection computer
Status ET415 becomes "STATUS 10" when driving with cruise control active (ET042
"Cruise control/speed limiter": CRUISE CONTROL) if the injection computer detects
a fault anywhere in the engine management system, or an engine speed that is too high
or too low.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then Perform fault finding on the injection computer.
Deal with present or stored faults.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status 10 continues, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-216
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR006
RAIL PRESSURE REGULATOR CURRENT
PARAMETER
DEFINITIONThis parameter indicates the current absorbed by the rail pressure regulator.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on.
PR006 = PR007 “Rail pressure regulator current setpoint” ± 5mA
Default value: 1600 mA
In the event of a fault, refer to the interpretation of faults DF053 Rail pressure regulation function and DF007
Rail pressure sensor circuit.
Engine running, engine coolant temperature > 80°C.
PR006 = PR007 “Rail pressure regulator current setpoint” ± 5mA
Default value: 1600 mA
In the event of a fault, consult the interpretation of fault DF007 Rail pressure sensor circuit.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR006/EDC16_V58_PR006/EDC16_V5C_PR006/EDC16_V18_PR006/EDC16_V1C_PR006/EDC16_V20_PR006

13B-217
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR007
RAIL PRESSURE REGULATOR CURRENT SETPOINT
PARAMETER
DEFINITIONThis parameter indicates the current setpoint absorbed by the rail pressure regulator.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on.
395 mA < PR007 < 405 mA
Default value: 1600 mA
In the event of a fault, refer to the interpretation of faults DF053 Rail pressure regulation function and DF007
Rail pressure sensor circuit.
Engine running, engine coolant temperature > 80°C.
1350 mA < PR007 < 1450 mA
Default value: 1600 mA
In the event of a fault, consult the interpretation of fault DF007 Rail pressure sensor circuit.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR007/EDC16_V58_PR007/EDC16_V5C_PR007/EDC16_V18_PR007/EDC16_V1C_PR007/EDC16_V20_PR007

13B-225
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR030
ACCELERATOR PEDAL POSITION
PARAMETER
DEFINITIONThis parameter indicates the accelerator pedal position as a percentage.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
No faults should be present or stored.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (e.g. lack of power).
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
>80 °C.
If no pressure is being applied to the pedal PR030 = 0%.
In the event of a fault, refer to the interpretation of fault DF008 Pedal potentiometer circuit gang 1 or DF009
Pedal potentiometer circuit gang 2.
Sensor electrical conformity.
Check the continuity and absence of interference resistance of the following connections:
– connection code 3LR,
– connection code 3LS,
– connection code 3LT,
– connection code 3LU,
– connection code3LW,
– connection code 3LV.
Between components 120 and 921.
If any of the connections are faulty and there is a repair method (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repairs), repair the wiring; otherwise replace the wiring.
Pedal sensor connected, vehicle ignition on and engine stopped:
– check the value of PR030:
0% no load,
100% full load,
138% full load after kickdown point on pedal.
– if the value is not correct, replace the pedal sensor.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR030/EDC16_V58_PR030/EDC16_V5C_PR030/EDC16_V18_PR030/EDC16_V1C_PR030/EDC16_V20_PR030