2011 RENAULT SCENIC sensor

13B-73
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF055
PRESENT
OR
STOREDTURBOCHARGING PRESSURE REGULATION CIRCUIT
1.DEF : Pressure too low
2.DEF : Pressure too high
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
– the engine is started,
– a road test.
Special notes:
If the fault is present:
- engine torque is limited,
- turbocharging regulation is inhibited,
- the EGR function is inhibited,
- the injection level 1 warning light is on.
Use bornier Elé. 1681 for any operations on the injection computer connectors.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
1.DEF
2.DEF
NOTESNone.
Check the condition of the turbocharging pressure sensor connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 1071).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Run test 2 Air line at the turbocharger.
Run test 3 Turbocharger control solenoid valve check.
Run test 4 Turbocharger.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF055/EDC16_V48_DF055/EDC16_V4C_DF055

13B-74
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF056
PRESENT
OR
STORED
AIR FLOWMETER CIRCUIT
CC.1 : short circuit to + 12 V
CO.0 : open circuit or short circuit to earth
1.DEF : offset at maximum threshold
2.DEF : offset at minimum threshold
3.DEF : parameter at max limit
4.DEF : parameter at minimum limit
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine is started or following a road test.
Special notes:
Use bornier Elé. 1681 for all operations on the injection computer connectors.
CC.1
NOTESNone.
Check the air flowmeter connections.
Check the injection computer connections.
Repair if necessary.
Check the continuity and insulation against + 12 V of the following connections:
Injection computer brown 48-track connector B, track E2 Track 2 air flow sensor
Injection computer brown 48-track connector B, track L4 Track 6 air flow sensor
Injection computer brown 48-track connector B, track G1 Track 5 air flow sensor
Injection computer brown 48-track connector B, track B4 Track 3 air flow sensor
Injection computer brown 48-track connector B, track G2 Track 1 air flow sensor
If the fault is still present, replace the air flowmeter.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF056/EDC16_V48_DF056/EDC16_V4C_DF056

13B-75
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF056
CONTINUED 1
CO.0
NOTESNone.
Check that there is a + 5 V supply on track 3 of the air flowmeter.
Repair if necessary.
Check the air flowmeter connections.
Check the injection computer connections.
Repair if necessary.
Check the continuity and insulation against earth between:
Injection computer brown 48-track connector B, track E2 Track 2 air flow sensor
Injection computer brown 48-track connector B, track B4 Track 3 air flow sensor
Injection computer brown 48-track connector B, track G1 Track 5 air flow sensor
Injection computer brown 48-track connector B, track G2 Track 1 air flow sensor connector
Injection computer brown 48-track connector B, track L4 Track 6 air flow sensor connector
PPM1 black connector of the UPC track 2 Track 4 air flow sensor connector
Repair if necessary.
If the fault is still present and remains present, replace the air flowmeter.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.

13B-76
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF056
CONTINUED 2
1.DEF
2.DEF
NOTESNone.
3.DEF
4.DEF
NOTESConditions for applying the fault finding procedure to
a stored fault:
The fault is declared present after the ignition has been
switched off for 15 seconds.
Check the air flowmeter connections.
Check the injection computer connections.
Repair if necessary.
Check the continuity and absence of interference resistance of the following connections:
Injection computer, brown 48-track connector B, track B4 Track 3 air flow sensor
Injection computer brown 48-track connector B, track G1 Track 5 air flow sensor
Injection computer, brown 48-track connector B, track L4 Track 6 air flow sensor
Injection computer, brown 48-track connector B, track E2 Track 2 air flow sensor
Injection computer, brown 48-track connector B, track G2 Track 1 air flow connector
PPM1 black connector of the UPC track 2 Track 4 air flow sensor connector
Repair if necessary.
Check the entire air inlet circuit:
– air filter unit inlet not blocked and filter not clogged,
–no foreign bodies on the air flow sensor grille (visual inspection only).
Otherwise, replace the air flow sensor.
– oil vapour recirculation circuit connected correctly,
–no leaks or blockages in the low and high pressure air circuits: pipes, presence and tightness of the mounting
clips, mounting of the turbocharger pressure sensor, intercooler, etc.
– check that the damper valve is open (valve control is against the body of the air vent unit).
With the flowmeter connected, the vehicle ignition on and engine stopped:
– check the voltage between tracks 2 and 5 of the flowmeter:
If the value is not 0.6 V ± 0.1, replace the air flow sensor.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.

13B-78
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF057
PRESENT
OR
STOREDWATER IN DIESEL FUEL DETECTOR CIRCUIT
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after the engine is started or following a road test.
A) Make sure the water in diesel fuel detection sensor is properly connected.
– If not, clear the fault,
– carry out a road test (speed > 12 mph (20 km/h) at an engine speed of> 1200 rpm) for more than 30 seconds.
– If the fault does not recur, end the fault finding procedure.
– If the fault does recur, go to step B.
B) If the sensor is properly connected:
– drain the diesel filter unit (seeMR 364, 13A, Fuel supply),
– clear the fault,
– carry out a road test (speed > 12 mph (20 km/h) at an engine speed of> 1200 rpm) for more than 30 seconds.
If the fault does not recur, end the fault finding procedure.
C) If the fault recurs:
–Check the continuity and the absence of unwanted resistance on the connection between:
Injection computer, grey 32-track connector C, track A2 Track 3 of the water detection sensor
–Check the power supply to the water detection sensor:
UPC PPM1 black connector track 2 Track 1 the water detection sensor
Earth Track 2 water detection sensor
– Carry out the necessary repairs.
If none of these checks reveal any faults:
– Replace the water detection sensor (see MR 364, 13A, Fuel supply).
– Clear the fault.
– Carry out a road test (speed > 12 mph (20 km/h) and engine speed > 1200 rpm) for more than 30 seconds,
to confirm the repair.
Note:
if the level of water in the fuel filter unit is lower than the sensor electrodes, certain driving conditions (on a bend,
leaning) may causethe injection warning light to light up erratically.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF057/EDC16_V48_DF057/EDC16_V4C_DF057

13B-85
DIESEL INJECTION
Fault finding - Interpretation of faults
13B
V10 MR-372-J84-13B150$376.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF097
PRESENT
OR
STOREDCAMSHAFT SENSOR CIRCUIT
1.DEF : no signal
2.DEF : inconsistent signal
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine is started or following a road test.
Special notes:
If the fault declared present before an attempt is made to start the engine it will not be
possible to start the engine.
Use bornier Ele. 1681 for all operations on the injection computer connectors.
1.DEF
2.DEF
NOTESPriority when dealing with a number of faults:
In the event of more than one fault:
–DF056 Air flow sensor circuit,
–DF057 Water in diesel fuel detector circuit,
–DF067 Damper control circuit,
Check the conformity of the + 12 V after relay supply line,
from track 2 of the UPC PPM1 connector.
(Use the Wiring Diagrams Technical Note for the vehicle).
Check the camshaft sensor connectors,
Check the injection computer connections.
Check that the camshaft sensor is correctly positioned and mounted.
Also check the general condition (damaged housing, heating up, etc.).
Carry out the necessary repairs.
Check the continuity and absence of interference resistance of the following connections:
Injection computer brown 48-track connector B, track D1 Track 2 Camshaft sensor
Injection computer brown 48-track connector B, track A1 Track 1 Camshaft sensor
Repair if necessary.
Check the camshaft sensor resistance between tracks 2 and 3.
If the resistance is not 10250Ω ±500 at 20°C, replace the sensor.
AFTER REPAIRDeal with any faults.
Carry out a road test, then check with the diagnostic tool.
EDC16_V44_DF097/EDC16_V48_DF097/EDC16_V4C_DF097

13B-86
DIESEL INJECTION
Fault finding - Interpretation of faults
13B
V10 MR-372-J84-13B150$376.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF097
CONTINUED
With the ignition on and the camshaft sensor connected:
Use a voltmeter to measure the voltage between tracks 1 and 3 of the camshaft sensor:
The voltage displayed should be equal to the battery voltage 0.08 V)
if the voltage is outside permitted tolerance values, take the measurement again with the camshaft sensor
disconnected.
If the voltage is still outside the permitted tolerance values with the sensor disconnected, check the continuity and
absence of interference resistance on the following connection:
Camshaft sensor, track 3 Track 2, PPM1 UPC black connector
If the voltage displayed is correct with the sensor disconnected, replace the camshaft sensor.
If the fault is still present, check the timing adjustment.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test, then check with the diagnostic tool.

13B-87
DIESEL INJECTION
Fault finding - Interpretation of faults
13B
V10 MR-372-J84-13B150$376.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF098
PRESENT
OR
STOREDFUEL TEMPERATURE SENSOR CIRCUIT
CC.0 : short circuit to earth
CO.1 : open circuit or short circuit to + 12 V
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present following a road test or after attempting to cold start the
engine.
Special notes:
– Use bornier Ele. 1681 for all operations on the injection computer connectors.
– The default value given by the diagnostic tool is 100°C.
CC.0
NOTESNone.
Check the fuel temperature sensor connections.
Check the injection computer connections.
Repair if necessary.
Measure the resistance of the fuel temperature sensor across tracks 1 and 2.
Replace the fuel temperature sensor if the resistance is not: 2050Ω ± 100 at 25°C
810Ω ± 47 at 50°C
309 Ω ± 17 at 80°C
Check the continuity and insulation from earth of the following connections:
Injection computer brown 48-track connector B, track H2 Track 1 fuel temperature sensor
Injection computer grey 32-track connector C, track F1 Track 2 fuel temperature sensor
If the fault is still present, replace the fuel temperature sensor.
AFTER REPAIRDeal with any faults.
Carry out a road test, then check with the diagnostic tool.
EDC16_V44_DF098/EDC16_V48_DF098/EDC16_V4C_DF098