2011 RENAULT SCENIC belt

AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Interpretation of faults
88C-35
88C
V3 MR-372-J84-88C000$071.mif
AIRBAG ACU4
VDIAG No.: 04
DF068
PRESENT
PASSENGER CHEST FRONT SIDE AIRBAG CIRCUIT
CC: Short circuit
CO: Open circuit
CC.1: Short circuit to + 12 V
CC.0: Short circuit to earth
1.DEF: Configuration
NOTESIf 1.DEF, check and modify the computer configuration.
Priorities when dealing with a number of faults: If DF068 is present with at least
one of faults DF210 or DF241, begin the fault finding by checking the 22-track under-
seat connector.
Special notes: never carry out measuring operations on trigger lines using any tool
other than CLIP or XRBAG.
Use the 64-track adapter (Elé. 1717) when working on the computer connector,
and use the 22-track adapter (Elé. 1687) when working on the seat connector.
CO - CC
NOTESSpecial notes: correct the trigger line configuration if the
vehicle is not fitted with passenger front chest-level side
airbags.
Lock the computer, disconnect the computer connector and fit the 64-track adapter (Elé. 1717). The CLIP or
XRBAG tool must be used to measure the resistance on the adapter cable marked F.
If the value obtained is correct, check the connections of the 64-track (tracks 43 and 44) connector.
Check the connections of the 22-track connector under the seat. Repair if necessary. Fit the 22-track test adapter
(Elé. 1687) underneath the seat (point C1).
The CLIP or XRBAG tool must be used to measure the resistance on cable A.
Is the value obtained correct?
NO
YES
Check the seat connector connections (tracks 11 and 12).
Strip the passenger seat and check that the side airbag module ignition module is connected correctly.
Disconnect the side airbag ignition module, connect a dummy ignition module to the ignition module
connector and measure the resistance on cable A again.
– If the value obtained is correct, replace the passenger's front chest side airbag module.
– If the value obtained is still not correct, replace the wiring between points C1 and C3 (seat wiring).
Check the seat connector connections again (tracks 11 and 12) as well as those of the 64-track
connector (tracks 43 and 44).
If the fault persists, the wiring is faulty between the computer and the passenger's seat (C0/C1).
Replace the wiring if necessary.
AFTER REPAIRReconnect the computer and the ignition module of the passenger's front side airbag
module then switch on the ignition again. Clear the computer memory then switch off
the ignition.
Carry out the check again using the diagnostic tool and, if there are no faults, unlock
the computer. When replacing the airbag module, do not forget to reconnect the earth
on the new one.
Destroy the chest level side airbag module if it has been replaced (tool Elé. 1287).
ACU4 Vdiag04 J84 1.0

AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Interpretation of faults
88C-36
88C
V3 MR-372-J84-88C000$071.mif
AIRBAG ACU4
VDIAG No.: 04
DF068
CONTINUED
CC.1 - CC.0
NOTESNone.
Lock the computer, disconnect the computer connector and fit the 64-track adapter (Elé. 1717). The CLIP or
XRBAG tool must be used to measure the appropriate insulation for the type of fault on the adapter cable
marked F.
If the value obtained is correct, check the connections of the 64-track (tracks 43 and 44) connector.
Check the connections of the 22-track connector under the seat. Repair if necessary. Fit the 22-track test
adapter (Elé. 1687) underneath the seat (point C1).
Only use the CLIP or XRBAG tool to measure the appropriate insulation for the type of fault on cable A.
Is the value obtained correct?
NO
YES
Passenger's seat wiring fault (C1/C3).
Replace the wiring if necessary.
Check the seat connector connections again (tracks 11 and 12) as well as those of
the 64-track connector (tracks 43 and 44).
If the fault persists, the wiring is faulty between the computer and the passenger's
seat (C0/C1).
Replace the wiring if necessary.
AFTER REPAIRReconnect the computer and the ignition module of the passenger's front side airbag
module then switch on the ignition again. Clear the computer memory then switch off
the ignition.
Carry out the check again using the diagnostic tool and, if there are no faults, unlock
the computer. When replacing the airbag module, do not forget to reconnect the earth
on the new one.
Destroy the chest level side airbag module if it has been replaced (tool Elé. 1287).
ACU4 Vdiag04 J84 1.0

AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Interpretation of faults
88C-37
88C
V3 MR-372-J84-88C000$071.mif
AIRBAG ACU4
VDIAG No.: 04
DF069
PRESENT
PASSENGER CURTAIN AIRBAG CIRCUIT
CO: Open circuit
CC: Short circuit
CC.1: Short circuit to + 12 V
CC.0: Short circuit to earth
1.DEF: Configuration
NOTESIf 1.DEF, check and modify the computer configuration.
Special notes: never carry out measuring operations on trigger lines using any tool
other than CLIP or XRBAG.
Use the 64-track adapter (Elé. 1717) when working on the computer connector.
CO - CC
NOTESSpecial notes: correct the trigger line configuration if the
vehicle is not fitted with a passenger side curtain airbag.
Lock the computer.
Switch off the ignition and check that the ignition module of the passenger side curtain airbag is properly
connected.
Disconnect the ignition module from the passenger's curtain airbag and connect a dummy ignition module to
the ignition module connector.
Switch on the ignition and carry out a check using the diagnostic tool.
Replace the passenger's curtain airbag if the fault becomes stored (fault no longer declared present).
Disconnect the 64-track computer connector and check the connector connections (tracks 45 and 46). Repair
if necessary.
Fit the 64-track test adapter (Elé. 1717) to the airbag wiring (point C0).
The CLIP or XRBAG tool must be used to measure the resistance on cable G. If the value indicated is
incorrect, the wiring between the computer connector and the passenger side curtain airbag (C0/C3) is faulty;
replace the wiring if necessary.
AFTER REPAIRReconnect the computer and the ignition module of the passenger side curtain airbag
module then switch the ignition back on. Clear the computer memory then switch off
the ignition.
Carry out the check again using the diagnostic tool and, if there are no faults, unlock
the computer.
Destroy the curtain side airbag module on the passenger side if it has been replaced
(tool Elé. 1287).
ACU4 Vdiag04 J84 1.0

AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Interpretation of faults
88C-38
88C
V3 MR-372-J84-88C000$071.mif
AIRBAG ACU4
VDIAG No.: 04
DF069
CONTINUED
CC.1 - CC.0
NOTESNone.
Lock the computer.
Disconnect the 64-track computer connector and check the connector connections (tracks 45 and 46). Repair
if necessary.
Fit the 64-track test adapter (Elé. 1717) to the airbag wiring (point C0).
The CLIP or XRBAG tool must be used to measure the appropriate insulation for the type of fault on cable G.
If the value indicated is incorrect, the wiring between the computer connector and the passenger side curtain
airbag (C0/C3) is faulty; replace the wiring if necessary.
AFTER REPAIRReconnect the computer and the ignition module of the passenger side curtain airbag
module then switch the ignition back on. Clear the computer memory then switch off
the ignition.
Carry out the check again using the diagnostic tool and, if there are no faults, unlock
the computer.
Destroy the curtain side airbag module on the passenger side if it has been replaced
(tool Elé. 1287).
ACU4 Vdiag04 J84 1.0

AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Interpretation of faults
88C-39
88C
V3 MR-372-J84-88C000$071.mif
AIRBAG ACU4
VDIAG No.: 04
DF070
PRESENT
DRIVER SIDE CURTAIN AIRBAG CIRCUIT
CO: Open circuit
CC: Short circuit
CC.1: Short circuit to + 12 V
CC.0: Short circuit to earth
1.DEF: Configuration
NOTESIf 1.DEF, check and modify the computer configuration.
Special notes: never carry out measuring operations on trigger lines using any tool
other than CLIP or XRBAG.
Use the 64-track adapter (Elé. 1717) when working on the computer connector.
CO - CC
NOTESSpecial notes: correct the trigger line configuration if the
vehicle is not fitted with a driver's side curtain airbag.
Lock the computer.
Switch off the ignition and make sure the ignition module of the driver's side curtain airbag is properly
connected.
Disconnect the ignition module from the driver side curtain airbag and connect a dummy ignition module to the
ignition module connector.
Switch on the ignition and carry out a check using the diagnostic tool.
Replace the driver's side curtain airbag if the fault becomes stored (fault no longer declared present).
Disconnect the 64-track computer connector and check the connector connections (tracks 17 and 18). Repair
if necessary.
Fit the 64-track test adapter (Elé. 1717) to the airbag wiring (point C0).
The CLIP or XRBAG tool must be used to measure the resistance on cable I. If the value obtained is incorrect,
the wiring between the computer connector and driver's side curtain airbag connector (C0/C3) is faulty; replace
the wiring if necessary.
AFTER REPAIRReconnect the computer and the ignition module of the driver's side curtain airbag
module then switch the ignition back on. Clear the computer memory then switch off
the ignition.
Carry out the check again using the diagnostic tool and, if there are no faults, unlock
the computer.
Destroy the curtain side airbag module on the driver's side if it has been replaced (tool
Elé. 1287).
ACU4 Vdiag04 J84 1.0

AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Interpretation of faults
88C-40
88C
V3 MR-372-J84-88C000$071.mif
AIRBAG ACU4
VDIAG No.: 04
DF070
CONTINUED
CC.1 - CC.0
NOTESNone.
Lock the computer.
Disconnect the 64-track computer connector and check the connector connections (tracks 17 and 18). Repair
if necessary.
Fit the 64-track test adapter (Elé. 1717) to the airbag wiring (point C0).
The CLIP or XRBAG tool must be used to measure the appropriate insulation for the type of fault on cable I.
If the value obtained is incorrect, the wiring between the computer connector and driver's side curtain airbag
connector (C0/C1) is faulty; replace the wiring if necessary.
AFTER REPAIRReconnect the computer and the ignition module of the driver's side curtain airbag
module then switch the ignition back on. Clear the computer memory then switch off
the ignition.
Carry out the check again using the diagnostic tool and, if there are no faults, unlock
the computer.
Destroy the curtain side airbag module on the driver's side if it has been replaced (tool
Elé. 1287).
ACU4 Vdiag04 J84 1.0

AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Interpretation of faults
88C-41
88C
V3 MR-372-J84-88C000$071.mif
AIRBAG ACU4
VDIAG No.: 04
DF071
PRESENT
DRIVER'S FRONT AIR BAG CIRCUIT 2
CC: Short circuit
CO: Open circuit
CC.1: Short circuit to + 12 V
CC.0: Short circuit to earth
1.DEF: Configuration
NOTESIf 1.DEF, check and modify the computer configuration.
Special notes: never carry out measuring operations on trigger lines using any tool
other than CLIP or XRBAG.
Use the 22-track adapter (Elé. 1685) when working on the computer connector.
CO - CC
NOTESNone.
Lock the computer using the command on the diagnostic tool.
Switch off the ignition and remove the driver's frontal airbag.
Check that it is correctly connected.
Disconnect the driver's frontal airbag and attach 2 dummy ignition modules to the ignition module connectors.
Switch on the ignition and carry out a check using the diagnostic tool.
Replace the driver's frontal airbag if the fault becomes stored (fault no longer declared present).
With the ignition switched off, disconnect and reconnect the connector of the rotary contact beneath the
steering wheel.
Check the connections if the fault has become stored (fault no longer declared present).
Fit the 10-track test adapter (Elé. 1617) to the rotary switch at point C2 (tracks 9 and 10).
The CLIP or XRBAG tool must be used for checking resistance on cable A.
If the value obtained is incorrect, replace the rotary switch beneath the steering wheel.
Reconnect the rotary switch under the steering wheel, disconnect the computer and check the connections of
the 22-track (tracks 4 and 15) connector.
Fit the 22-track test adapter (Elé. 1685).
The CLIP or XRBAG tool must be used to measure the resistance on adapter cable D.
If the value obtained is incorrect, the wiring is faulty between the computer and the rotary switch connector
(C0/C2). Replace the wiring if necessary.
AFTER REPAIRReconnect the computer and driver's frontal airbag ignition modules, then switch on
the ignition again.
Clear the computer memory then switch off the ignition.
Carry out the check again using the diagnostic tool and, if there are no faults, unlock
the computer. When replacing the airbag module, do not forget to reconnect the earth
on the new one.
Destroy the driver's front airbag if it has been replaced (tool Elé. 1287).
ACU4 Vdiag04 J84 1.0

AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Interpretation of faults
88C-42
88C
V3 MR-372-J84-88C000$071.mif
AIRBAG ACU4
VDIAG No.: 04
DF071
CONTINUED
CC.1 - CC.0
NOTESNone.
Lock the computer using the command on the diagnostic tool.
Switch off the ignition and unclip the driver's frontal airbag.
Check the condition and correct connection of the trigger lines.
Fit the 10-track test adapter to the rotary switch at point C2 (tracks 9 and 10).
The CLIP or XRBAG tools must be used to measure the appropriate insulation for the type of fault on cable A
(driver's front airbag connected).
If the value obtained is incorrect, replace the rotary switch beneath the steering wheel.
Reconnect the rotary switch under the steering wheel, disconnect the computer and check the connector
connections (tracks 4 and 15).
Fit the 22-track test adapter (Elé. 1685).
The CLIP or XRBAG tool must be used to measure the appropriate insulation for the type of fault on adapter
cable D.
If the value obtained is incorrect, the wiring is faulty between the computer and the rotary switch connector
(C0/C2). Replace the wiring if necessary.
AFTER REPAIRReconnect the computer and driver's frontal airbag ignition modules, then switch on the
ignition again.
Clear the computer memory then switch off the ignition.
Carry out the check again using the diagnostic tool and, if there are no faults, unlock
the computer. When replacing the airbag module, do not forget to reconnect the earth
on the new one.
Destroy the driver's front airbag if it has been replaced (tool Elé. 1287).
ACU4 Vdiag04 J84 1.0