Page 168 of 276
166
BATTERY
The battery is located under the bonnet.
For access to it:
)
open the bonnet using the interior release lever, then the exterior
safety catch,
)
remove the plastic cover for access to the two terminals,
)
wait 2 minutes after switching off the ignition before disconnecting
the battery,
)
unclip the fusebox to remove the battery, if necessary.
STARTING USING ANOTHER BATTERY
)
Connect the red cable to the positive terminal (+) of the fl at
battery A
, then to the positive terminal (+) of the slave battery B
.
)
Connect one end of the green or black cable to the negative
terminal (-) of the slave battery B
.
)
Connect the other end of the green or black cable to the earth
point C
on the broken down vehicle.
)
Operate the starter, let the engine run.
)
Wait until the engine returns to idle and disconnect the cables.
ACCESS TO THE BATTERY
The batteries contain harmful substances such as sulphuric
acid and lead. They must be disposed of in accordance with
regulations and must not, in any circumstances, be discarded with
household waste.
Take used remote control batteries and vehicle batteries to a
special collection point.
Page 169 of 276
8/
PRACTICAL INFORMATION
DISCONNECTING/RECONNECTING THE
CABLES
To avoid discharging the battery, do not leave the vehicle lighting
on repeatedly with the ignition off (refer to the "Energy economy
mode" paragraph).
It is advisable to disconnect the battery if the vehicle is to be left
unused for more than one month.
Do not disconnect the terminals while the engine is running.
Do not charge the batteries without disconnecting the terminals fi rst.
Before disconnecting the battery
Wait 2 minutes after switching off the ignition before disconnecting
the battery.
Retract the active spoiler then close the windows and the doors
before disconnecting the battery.
Following reconnection of the battery
Following reconnection of the battery, switch on the ignition
and wait 1 minute before starting to permit initialisation of the
electronic systems. However, if slight problems remain following
this operation, contact a PEUGEOT dealer or a qualifi ed
workshop.
Referring to the corresponding section, you must yourself
reinitialise:
- the remote control key,
- the electric windows and the automatic partial opening of the
door windows,
- the GPS satellite navigation system.
)
Raise the locking tab D
fully.
)
Position the open clip E
of the cable on the positive terminal (+) of
the battery.
)
Press vertically on the clip E
to position it correctly against the
battery.
)
Lock the clip by lowering the tab D
.
CHARGING THE BATTERY USING A BATTERY
CHARGER
)
Disconnect the battery from the vehicle.
)
Follow the instructions for use provided by the manufacturer of the
charger.
)
Reconnect starting with the negative terminal (-).
)
Check that the terminals and connectors are clean. If they are
covered with sulphate (whitish or greenish deposit), remove them
and clean them.
Do not force the tab as locking will not be possible if the clip is not
positioned correctly.
Start the procedure again.
Page 175 of 276
8/
PRACTICAL INFORMATION
Changing reversing lamps and foglamps
These two bulbs are changed from outside the rear bumper:
)
unclip the protective cover from the rear, then tilt it,
)
remove it completely to gain access to the two lamp fi xing bolts,
On the left-hand side, take care not to touch the silencer; risk
of burns, if you change the bulb immediately after switching
off the ignition.
)
turn these two bolts one quarter of a turn and remove them,
)
push the lamp towards the inside to unclip it, then tilt it,
)
pull the lamp towards the outside for access to the various bulb-
holders.
- For the reversing lamps: pull the corresponding bulb holder,
- turn the bulb one quarter of a turn and change it.
- For the foglamp: turn the bulb holder one quarter of a turn and
remove it,
- turn the bulb one quarter of a turn and change it.
To refi t, carry out these operations in reverse order.
Page 177 of 276
8/
PRACTICAL INFORMATION
CHANGING A FUSE
ACCESS TO THE TOOLS
The extraction tweezer is fi tted to the back of the dashboard fusebox
cover.
To gain access to them:
)
turn the screw a quarter of a turn to the left,
)
unclip the cover by pulling at the top right,
)
remove the cover completely and turn it over,
)
remove the carrier on which is fi tted the tweezer.
CHANGING A FUSE
Before changing a fuse, tit is necessary to:
)
identify the cause and correct it,
)
switch off all electrical consumers,
)
immobilise the vehicle and switch off the ignition,
)
identify the failed fuse using the allocation tables and drawings
presented on the following pages.
To replace a fuse, you must:
- use the special tweezer to extract the fuse from its housing and
check the condition of its fi lament,
- always replace a failed fuse with a fuse of the same rating (same
colour); a different rating fuse may cause malfunctions (risk of fi re).
Good
Failed
Tweezer
If the fault recurs soon after changing a fuse, have the electrical
system of your vehicle checked by a PEUGEOT dealer or a
qualifi ed workshop.
Page 179 of 276
8/
F2
F15F11
F9 F6 F5 F1 F7 F4 F3 F10 F8 F13 F12 F14F17 SH
PRACTICAL INFORMATION
DASHBOARD FUSES
The fusebox is placed in the lower section of the dashboard (left-hand
side). It consists of two boxes.
Access to the fuses
)
Refer to the paragraph "Access to the tools".
Fuse tables
Fuse N°
Rating
Functions
F1
-
Not used.
F2
30 A
Locking and deadlocking earth.
F3
5 A
Airbags, active bonnet and pretensioners
control unit.
F4
10 A
Clutch pedal switch, electrochromatic
rear view mirror, automatic gearbox,
switching and protection unit.
F5
30 A
One-touch electric windows, folding door
mirrors supply.
F6
-
Not used.
F7
5 A
Front and rear courtesy lamps, map
reading lamps, sun visor lighting, glove
box lighting.
F8
20 A
Audio equipment, audio/telephone,
multifunction screen, tyre under-infl ation
detection, clock,
F9
30 A
12 V socket.
F10
15 A
Steering mounted controls.
F11
15 A
Low current ignition switch.
F12
15 A
Instrument panel, air conditioning,
driver's seat memory unit, rain/sunshine
sensor, airbags.
Box 1
Page 181 of 276
8/
F10
F11
F13F14F12
F20
F19
F18
F17
F16
F15
F4
F8F2
F3F5 F7
F9
F6
F21 F1
PRACTICAL INFORMATION
ENGINE COMPARTMENT FUSES
The fusebox is placed in the engine compartment near the battery (left-
hand side).
Access to the fuses
)
Unclip the cover.
)
Change the fuse (see corresponding paragraph).
)
When you have fi nished, close the cover carefully to assure the
sealing of the fusebox.
Fuse table
Fuse N°
Rating
Functions
F1
20 A
Engine control unit supply, injection
pump and EGR electrovalves (Diesel),
injectors (Diesel).
F2
15 A
Horn.
F3
10 A
Front wash-wipe.
F4
20 A
Daytime running lamps.
F5
15 A
Air fl ow sensor, coolant pump, oil pump,
thermostat, blow-by heater (petrol),
by-pass and EGR electrovalves (Diesel),
diesel heater (Diesel).
F6
10 A
Steering wheel angle sensor, ABS/ESP
control unit, ESP control unit.
F7
10 A
Power steering control unit, automatic
gearbox, engine coolant level detector,
dual function brake switch.
F8
25 A
Starter motor control.
F9
10 A
Diagnostic socket, directional
headlamps, particle emission fi lter pump
(Diesel).
F10
30 A
Engine control unit actuators (petrol:
ignition coils, electrovalves, injectors,
fuel pump (Diesel: electrovalves,
heaters).
F11
40 A
Air conditioning blower.
Page 182 of 276
F10
F11
F13F14F12
F20
F19
F18
F17
F16
F15
F4
F8F2
F3F5 F7
F9
F6
F21 F1
180
Fuse N°
Rating
Functions
F12
40 A
Windscreen wipers slow/fast speed.
F13
40 A
Built-in systems interface supply (ignition
positive).
F14
-
Not used.
F15
10 A
Right-hand main beam headlamp.
F16
10 A
Left-hand main beam headlamp.
F17
15 A
Left-hand dipped headlamp.
F18
15 A
Right-hand dipped headlamp.
F19
15 A
Variable timing electrovalve, oxygen
sensors (petrol), electrovalves (Diesel).
F20
10 A
Turbine discharge and canister purge
electrovalves (petrol), air fl ow sensor
(1.6 l THP 200), water in diesel sensor
(Diesel).
F21
5 A
Fans control, Turbo pump (petrol),
Valvetronic motor (1.6 l THP 200).
Page 185 of 276
8/
PRACTICAL INFORMATION
TOWING YOUR VEHICLE
)
On the front bumper, unclip the cover by pressing at the bottom.
)
Screw the towing eye in fully.
)
Install the towing bar.
)
Place the gear lever in neutral (position N
on the automatic
gearbox).
Failure to observe this instruction could result in damage to certain
components (braking, transmission...) and the absence of braking
assistance the next time the engine is started.
)
Unlock the steering by turning the ignition key one notch and
release the parking brake.
)
Switch on the hazard warning lamps on both vehicles.
)
Move off gently and drive slowly and for a short distance only.
TOWING ANOTHER VEHICLE
)
On the rear bumper, unclip the cover by pressing at the bottom.
)
Screw the towing eye in fully.
)
Install the towing bar.
)
Switch on the hazard warning lamps on both vehicles.
)
Move off gently and drive slowly and for a short distance only.
