2011 Peugeot RCZ ignition
[x] Cancel search: ignitionPage 138 of 276
SET/+LIM
IT
CRUISE 0 I
I
SE
T/
–
136
CRUISE CONTROL
System which automatically maintains the speed of the vehicle at the
value programmed by the driver, without any action on the accelerator
pedal.
The cruise control is switched off
manually or by pressing the brake or
clutch pedal or on triggering of the ESP system for safety reasons.
Switching off the ignition cancels any programmed speed value.
STEERING MOUNTED CONTROL
The functions of this system are grouped together on the steering
mounted control.
1.
Cruise control mode selection dial.
2.
Speed programming/value decrease button.
3.
Speed programming/value increase button.
4.
Cruise control off/resume button.
The cruise control cannot, in any circumstances, replace the need
to respect speed limits, nor can it replace the need for vigilance
and responsibility on the part of the driver.
You are advised to keep your feet near the pedals at all times. The cruise control is switched on
manually: it requires a minimum
vehicle speed of 25 mph (40 km/h) and the engaging:
- of fourth gear on the manual gearbox,
- of second gear on the automatic gearbox, in sequential driving
mode,
- of position D
on the automatic gearbox.
It is possible to exceed the programmed speed temporarily by pressing
the accelerator pedal.
To return to the programmed speed, simply release the accelerator
pedal.
Page 143 of 276
6/
DRIVING
Deactivation/Activation of the rear parking sensors
The function is deactivated or activated via the vehicle
confi guration menu.
The status of the function is stored when the ignition is
switched off.
For more information on access to the parking sensors menu,
refer to the section covering the confi guration of vehicle systems.
OPERATING FAULT
In the event of a malfunction of the system, when reverse gear
is engaged this warning lamp is displayed in the instrument
panel and/or a message appears in the screen, accompanied
by an audible signal (short beep).
Contact a PEUGEOT dealer or a qualifi ed workshop.
In bad weather or in winter, ensure that the sensors are not
covered with mud, ice or snow. When reverse gear is engaged, an
audible signal (long beep) indicates that the sensors may be dirty.
When the vehicle is moving at a speed below 6 mph (10 km/h),
certain sound sources (motorcycle, lorry, pneumatic drill, etc.) may
trigger the audible signals of the parking sensor system.
The function will be deactivated automatically if a trailer is being
towed or a bicycle carrier is fi tted (vehicle fi tted with a towbar or
bicycle carrier recommended by PEUGEOT).
Page 145 of 276
7/
ESSENCE SANS PLOMB
UNLEADED FUEL ONLY
NUR BLEIFREI BENZIN
GASOLINA SIN PLOMO
RON 95/98
CHECKS
FUEL TANK
Fuel tank capacity: approximately 55 litres.
LOW FUEL LEVEL
FILLING
When the fuel tank minimum level is reached this warning
lamp comes on on the instrument panel, accompanied by an
audible signal and an alert message. When it fi rst comes on
there remains approximately 5 litres
of fuel in the tank.
Until suffi cient fuel is added, this warning lamp appears every time
the ignition is switched on, accompanied by an audible signal and a
message. When driving, this audible signal and display of the alert
message are repeated with increasing frequency as the fuel level drops
towards "0"
.
Refuel as soon as possible to avoid running out of fuel.
If you run out of fuel (Diesel), refer also to the "Running out of fuel
(Diesel)" section.
A label affi xed to the inside of the fl ap reminds you of the type of fuel to
be used depending on your engine.
Additions of fuel must be of at least 5 litres, in order to be taken into
account by the fuel gauge. To fi ll the tank in complete safety:
)
the engine must be switched off,
)
press the rear part of the fl ap, then raise it to open it,
)
turn the cap to the left,
)
remove the cap and hook it onto the clip located on the inside of the
fl ap,
)
fi ll the tank, but do not continue after the 3rd cut-off of the
pump
; this could cause malfunctions. Opening the fi ller cap may create a noise a caused by an inrush
of air. This vacuum is entirely normal, resulting from the sealing of
the fuel system.
Page 151 of 276
7/
CHECKS
CHECKING LEVELS
Check all of these levels regularly and top them up if necessary, unless
otherwise indicated.
If a level drops signifi cantly, have the corresponding system checked by
a PEUGEOT dealer or a qualifi ed workshop.
OIL LEVEL
The check is carried out either when the ignition is switched
on using the oil level indicator on the instrument panel, or
using the dipstick.
This manual check will only be correct if the vehicle is on level ground
and the engine has been off for more than 30 minutes.
After topping up the oil, the check when switching on the ignition
with the oil level indicator in the instrument panel will only be valid
30 minutes after topping up.
It is normal to top up the oil level between services. PEUGEOT
recommends that you check the oil level and top up if necessary
every 3 000 miles (5 000 kilometres).
Engine oil change
Refer to the Warranty and Maintenance Record for details of the interval
for this operation.
In order to maintain the reliability of the engine and emission control
system, the use of additives in the engine oil is prohibited.
BRAKE FLUID LEVEL
The brake fl uid level should be close to the "MAX" mark. If it is
not, check the brake pad wear.
Changing the fluid
Refer to the Warranty and Maintenance Record for details of the interval
for this operation.
Fluid specification
The brake fl uid must conform to the manufacturer's recommendations
and meet the DOT4 standard.
POWER STEERING FLUID LEVEL
The power steering fl uid level should be close to the "MAX"
mark. Unscrew the cap, with the engine cold, to check the level.
When working under the bonnet, take care, as certain areas of the
engine may be extremely hot (risk of burns).
Oil specification
The oil must be the correct grade for your engine and conform to the
manufacturer's recommendations.
Page 152 of 276
F0
150
COOLANT LEVEL
The coolant level should be close to the "MAX" mark but
should never exceed it.
When the engine is warm, the temperature of the coolant is regulated
by the fan. This can operate with the ignition off.
On vehicles which are fi tted with a particle emission fi lter, the fan
may operate after the vehicle has been switched off, even if the
engine is cold.
In addition, as the cooling system is pressurised, wait at least one hour
after switching off the engine before carrying out any work.
To avoid any risk of scalding, unscrew the cap by two turns to allow the
pressure to drop. When the pressure has dropped, remove the cap and
top up the level.
Changing the coolant
The coolant does not have to be changed.
Fluid specification
The coolant must conform to the manufacturer's recommendations.
SCREENWASH AND HEADLAMP WASH FLUID
In the case of vehicles fi tted with headlamp washers, the low
fl uid level is indicated by an audible signal and a message in
the instrument panel screen.
Top up the reservoir when you stop the vehicle.
Fluid specification
For optimum cleaning and to avoid freezing, this fl uid must not be
topped up with or replaced with plain water.
ADDITIVE LEVEL (DIESEL WITH PARTICLE
EMISSIONS FILTER)
The additive reservoir low level is indicated by fi xed illumination
of this warning lamp, accompanied by an audible signal and a
message that the particle emissions fi lter additive level is too low.
Topping up
The reservoir must be topped up without delay by a PEUGEOT dealer
or a qualifi ed workshop.
USED PRODUCTS
Avoid prolonged contact of used oil or fl uids with the skin.
Most of these fl uids are harmful to health or indeed very corrosive.
Do not discard used oil or fl uids into sewers or onto the ground.
Take used oil to a PEUGEOT dealer or a qualifi ed workshop
(France) or to an authorised waste disposal site.
Page 157 of 276
8/
0
0
0
0
PRACTICAL INFORMATION
Take care, this product is harmful (e.g. ethylene-glycol,
colophony...) if swallowed and causes irritation to the eyes.
Keep it out of reach of children.
REPAIR PROCEDURE
1. Sealing
)
Switch off the ignition.
)
Turn the selector A
to the "sealant" position.
)
Check that the switch B
is in position "O"
.
)
Uncoil the white pipe G
fully.
)
Unscrew the cap from the white pipe.
)
Connect the white pipe to the valve of the tyre to be repaired.
)
Connect the compressor's electric plug to the vehicle's 12 V socket.
)
Start the vehicle and leave the engine running.
Avoid removing any foreign bodies which have penetrated into the
tyre.
Page 162 of 276
160
CHANGING A WHEEL
Parking the vehicle
Immobilise the vehicle where it does not block traffi c: the ground
must be level, stable and non-slippery ground.
Apply the parking brake, switch off the ignition and engage fi rst
gear (position P
for the automatic gearbox) to lock the wheels.
It is imperative that you ensure that the occupants get out of the
vehicle and wait where they are safe.
If necessary, place a chock under the wheel diagonally opposite
the wheel to be changed.
Never go underneath a vehicle raised using a jack; use an axle
stand.
Security socket: for adaptation of the
wheelbrace to the special "security" bolts.
Specifi c to your vehicle, it is stored in the
glove box.
Wheelbrace: for removal of the wheel fi xing
bolts.
Jack with integrated handle: for lifting the
vehicle.
TOOLS REQUIRED *
Bolt cover removal tool: for removal of the
bolt fi nishers (covers) on alloy wheels.
*
Depending on the country of sale, the vehicle may be equipped with
the tools needed to change a wheel and a spare wheel (see following
pages).
Page 166 of 276
164
CHANGING A WIPER BLADE
BEFORE REMOVING A WIPER BLADE
)
Within one minute after switching off the ignition, operate the wiper
stalk to position the wiper blades in the centre of the windscreen.
REMOVING
)
Raise the corresponding wiper arm.
)
Unclip the wiper blade and remove it.
FITTING
)
Put the corresponding new wiper blade in place and clip it.
)
Fold down the wiper arm carefully.
AFTER FITTING A WIPER BLADE
)
Switch on the ignition.
)
Operate the wiper stalk again to park the wiper blades.
Access to tools *
)
Open the boot lid.
)
Lift the boot fl oor using its strap.
)
Fix it in the vertical position beyond the stops located on the boot
sides.
)
Remove the temporary puncture repair kit for access to the jack.
* According to country. All of these tools are specifi c to your vehicle. Do not use them for
other purposes.