2011 Peugeot RCZ ESP
[x] Cancel search: ESPPage 115 of 276
5/
a
i
r
b
a
g
airbag
SAFETY
Reactivation
When you remove the child seat, turn the switch to the "ON"
position to
reactivate the airbag and so assure the safety of your front passenger in
the event of an impact.
With the ignition on, this warning lamp comes on in the seat
belt and passenger's front airbag warning lamps display for
approximately one minute, if the passenger's front airbag is
activated.
If even one of the two airbag warning lamps comes on
continuously, do not install a child seat on the front passenger
seat.
Have the system checked by a PEUGEOT dealer or a qualifi ed
workshop.
Operating fault
If this warning lamp comes on in the instrument panel,
accompanied by an audible warning and a message in the
screen, contact a PEUGEOT dealer or a qualifi ed workshop
to have the system checked. The airbags may no longer be
deployed in the event of a serious impact.
If this warning lamp fl ashes in the passenger's front airbag
warning lamps display, contact a PEUGEOT dealer or a
qualifi ed workshop. The passenger's front airbag may no
longer be deployed in the event of a serious impact.
LATERAL AIRBAGS
System which protects the driver and front passenger in the event of a
violent side impact in order to limit the risks of injury to the chest.
Each lateral airbag is fi tted in the front seat back frame, on the door
side.
Deployment
It is deployed unilaterally in the event of a violent impact applied to
all or part of the side impact zone B
, operating at right angles to the
longitudinal axis of the vehicle in a horizontal plane and from the
exterior of the vehicle towards the interior.
The lateral airbag comes between the front occupant of the vehicle and
the corresponding door trim panel.
Page 130 of 276
mph
mi.
l/100
55
500 LIMIT Pause
10,2
4
128
*
According to engine.
GEAR SHIFT INDICATOR *
System which reduces fuel consumption by advising the driver to
change up on vehicles fi tted with a manual gearbox.
OPERATION
The system intervenes only when driving economically.
Depending on the driving situation and your vehicle's equipment, the
system may advise you to skip one or more gears. You can follow this
instruction without engaging the intermediate gears.
The gear engagement recommendations must not be considered
compulsory. In fact, the confi guration of the road, the amount of traffi c
and safety remain determining factors when choosing the best gear.
Therefore, the driver remains responsible for deciding whether or not to
follow the advice given by the system.
This function cannot be deactivated.
In the case of driving which makes particular demands on the
performance of the engine (fi rm pressure on the accelerator pedal,
for example, when overtaking...), the system will not recommend
a gear change.
The system never suggests:
- engaging fi rst gear,
- engaging reverse gear,
- engaging a lower gear.
The information appears in the instrument panel screen in the form of
an arrow accompanied by the suggested gear.
Example:
- You are in third gear.
- You press the accelerator pedal moderately.
- The system may suggest that you engage a higher gear,
if appropriate.
Page 132 of 276
33
33
130
DISPLAYS IN THE INSTRUMENT PANEL
When you move the lever in the gate to select a position, the
corresponding indicator lamp is displayed in the instrument panel.
P.
Park
R.
Reverse
N.
Neutral
D1... D6.
Drive (Automatic driving)
S.
Sport
programme
7
. Snow
programme
M1... M6.
Manual (Sequential driving)
-.
Invalid value during manual operation
MOVING OFF
)
Apply the parking brake.
)
Select position P
or N
.
)
Start the engine.
If this procedure is not followed, there is an audible signal, accompanied
by a message in the screen.
)
With the engine running, press the brake pedal.
)
Release the parking brake.
)
Select position R
, D
or M
,
)
Gradually release the brake pedal.
The vehicle moves off immediately.
If position N
is engaged inadvertently while driving, allow the
engine to return to idle then engage position D
to accelerate.
When the engine is running at idle, with the brakes released,
if position R
, D
or M
is selected, the vehicle moves even without
the accelerator being pressed.
When the engine is running, never leave children in the vehicle
without supervision.
When carrying out maintenance with the engine running, apply the
parking brake and select position P
.
A message appears if you try to move the gear lever from
position P
to another position without pressing the brake pedal.
Page 135 of 276
6/
SE
T/+LIMI
T
CRUISE 0 II
SE
T/–
DRIVING
SPEED LIMITER
System which prevents the vehicle from exceeding the speed
programmed by the driver.
When the programmed speed limit is reached, pressing the accelerator
pedal no longer has any effect.
The speed limiter is switched on
manually: it requires a programmed
speed of at least 20 mph (30 km/h).
The speed limiter is switched off
by manual operation of the control.
The programmed speed can be exceeded temporarily by pressing the
accelerator fi rmly.
To return to the programmed speed, simply slow down to a speed below
the programmed speed.
The programmed speed remains in the memory when the ignition is
switched off.
The speed limiter cannot, in any circumstances, replace the need
to respect speed limits, nor can it replace the need for vigilance
and responsibility on the part of the driver.
STEERING MOUNTED CONTROL
The functions of this system are grouped together on steering mounted
control.
1.
Speed limiter mode selection dial.
2.
Value decrease button.
3.
Value increase button.
4.
Speed limiter on/off button.
Page 138 of 276
SE
T/+LIM
IT
CRUISE 0 II
S
ET/–
136
CRUISE CONTROL
System which automatically maintains the speed of the vehicle at the
value programmed by the driver, without any action on the accelerator
pedal.
The cruise control is switched off
manually or by pressing the brake or
clutch pedal or on triggering of the ESP system for safety reasons.
Switching off the ignition cancels any programmed speed value.
STEERING MOUNTED CONTROL
The functions of this system are grouped together on the steering
mounted control.
1.
Cruise control mode selection dial.
2.
Speed programming/value decrease button.
3.
Speed programming/value increase button.
4.
Cruise control off/resume button.
The cruise control cannot, in any circumstances, replace the need
to respect speed limits, nor can it replace the need for vigilance
and responsibility on the part of the driver.
You are advised to keep your feet near the pedals at all times. The cruise control is switched on
manually: it requires a minimum
vehicle speed of 25 mph (40 km/h) and the engaging:
- of fourth gear on the manual gearbox,
- of second gear on the automatic gearbox, in sequential driving
mode,
- of position D
on the automatic gearbox.
It is possible to exceed the programmed speed temporarily by pressing
the accelerator pedal.
To return to the programmed speed, simply release the accelerator
pedal.
Page 141 of 276
6/
... BIP ... BIP ... BIP ...
DRIVING
This function cannot, in any circumstances, take the place of the
vigilance and responsibility of the driver.
Certain types of obstacle (stake, roadworks cone, etc.) detected
initially will no longer be detected at the end of the manoeuvre due
to the presence of blind spots.
PARKING SENSORS
This system indicates the proximity of an obstacle (person, vehicle, tree,
gate, etc.) which comes within the fi eld of detection of sensors located
in the bumper.
REAR PARKING SENSORS
The system is switched on by engaging reverse gear. This is
accompanied by an audible signal.
The system is switched off when you exit reverse gear.
Audible assistance
The proximity information is given by an intermittent audible signal, the
frequency of which increases as the vehicle approaches the obstacle.
The sound emitted by the speaker (right or left) indicates the side on
which the obstacle is located.
When the distance between the vehicle and the obstacle becomes
less than approximately thirty centimetres, the audible signal becomes
continuous.
Page 151 of 276
7/
CHECKS
CHECKING LEVELS
Check all of these levels regularly and top them up if necessary, unless
otherwise indicated.
If a level drops signifi cantly, have the corresponding system checked by
a PEUGEOT dealer or a qualifi ed workshop.
OIL LEVEL
The check is carried out either when the ignition is switched
on using the oil level indicator on the instrument panel, or
using the dipstick.
This manual check will only be correct if the vehicle is on level ground
and the engine has been off for more than 30 minutes.
After topping up the oil, the check when switching on the ignition
with the oil level indicator in the instrument panel will only be valid
30 minutes after topping up.
It is normal to top up the oil level between services. PEUGEOT
recommends that you check the oil level and top up if necessary
every 3 000 miles (5 000 kilometres).
Engine oil change
Refer to the Warranty and Maintenance Record for details of the interval
for this operation.
In order to maintain the reliability of the engine and emission control
system, the use of additives in the engine oil is prohibited.
BRAKE FLUID LEVEL
The brake fl uid level should be close to the "MAX" mark. If it is
not, check the brake pad wear.
Changing the fluid
Refer to the Warranty and Maintenance Record for details of the interval
for this operation.
Fluid specification
The brake fl uid must conform to the manufacturer's recommendations
and meet the DOT4 standard.
POWER STEERING FLUID LEVEL
The power steering fl uid level should be close to the "MAX"
mark. Unscrew the cap, with the engine cold, to check the level.
When working under the bonnet, take care, as certain areas of the
engine may be extremely hot (risk of burns).
Oil specification
The oil must be the correct grade for your engine and conform to the
manufacturer's recommendations.
Page 166 of 276
164
CHANGING A WIPER BLADE
BEFORE REMOVING A WIPER BLADE
)
Within one minute after switching off the ignition, operate the wiper
stalk to position the wiper blades in the centre of the windscreen.
REMOVING
)
Raise the corresponding wiper arm.
)
Unclip the wiper blade and remove it.
FITTING
)
Put the corresponding new wiper blade in place and clip it.
)
Fold down the wiper arm carefully.
AFTER FITTING A WIPER BLADE
)
Switch on the ignition.
)
Operate the wiper stalk again to park the wiper blades.
Access to tools *
)
Open the boot lid.
)
Lift the boot fl oor using its strap.
)
Fix it in the vertical position beyond the stops located on the boot
sides.
)
Remove the temporary puncture repair kit for access to the jack.
* According to country. All of these tools are specifi c to your vehicle. Do not use them for
other purposes.