2011 PEUGEOT 4007 ECO mode

1
INSTRUMENTS and CONTROLS
Set the time using the buttons as
indicated below:


)
with the ignition on or in the ACC
(Accessories) position, press and
hold the CLOCK
button until the
time display fl ashes.

)
Press the appropriate button to set
the time:

Button
H:
to set the hours
The hours digits scroll when you press
this button.

Button M:
to set the minutes
The minutes digits scroll when you
press this button.

Button 00:
to reset the minutes to
zero.


- from 1 to 29 min
:
rounded down to
the previous hour,

- from 30 to 59 min:
rounded up to
the next hour.


)
After setting the time, press the
DISP
button; the time display stops
fl ashing.


Manual mode

Automatic mode

In this mode, setting is automatic using
the signal from the RDS radio stations. The digital clock does not display
seconds.
When the "minutes" display is
set or reset to zero, the clock
starts at the zero second of the
minute selected.
The time setting is lost if the
battery is disconnected.


)
Turn button B
"TUNE" to the left or
to the right to select "CT ON"
(auto-
matic mode) or "CT OFF"
(manual
mode).

)
After selecting the mode, you can
exit the "Functions setting mode"
menu by pressing button B
"TUNE"
for approximately 2 seconds.
If no action is carried out within
10 seconds, the system will exit
the "Functions setting mode"
menu automatically.

2
COMFORT

Intake of exterior air/
Recirculation of interior air (6)
This function insulates the passenger
compartment from exterior odours and
smoke.


)
Press button 6
to select the air in-
take mode.
When the indicator lamp in button 6
is
off, the exterior air intake function is ac-
tivated.
When the indicator lamp in button 6
is
on, the intake of exterior air is deacti-
vated and the system is in air recircula-
tion mode.
Rear screen demisting/
defrosting (4)
With the engine running, press button 4

to activate the demisting/defrosting of
the rear screen and door mirrors.
The indicator lamp on the button comes
on while demisting/defrosting is in op-
eration.
Demisting/defrosting switches off auto-
matically to prevent an excessive con-
sumption of current.
Demisting/defrosting can be stopped
before it is switched off automatically
by pressing the button again.
It is advisable to switch off rear
screen demisting/defrosting as
soon as possible as lower cur-
rent consumption reduces fuel
consumption.
Air conditioning On/Off (5)
Do not drive for long periods in
interior air recirculation mode,
except in truly exceptional at-
mospheric conditions.
Personalisation of the Air
Conditioning On/Off function
This function is controlled automatically.
However, you can deactivate its auto-
matic control if you wish to switch the air
conditioning on or off at any time.

Changing the status
Press the Air Conditioning On/Off button
for at least 10 seconds.
When the status changes from active to
inactive, three bleeps are heard and the
indicator lamp fl ashes three times.
When the status changes from inactive
to active, two bleeps are heard and the
indicator lamp fl ashes three times.

Automatic control active
If the air distribution adjustment dial and
the air fl ow adjustment dial are placed
in the "AUTO" position, or if the temper-
ature control dial is set to the minimum
temperature, the air conditioning sys-
tem is controlled automatically.

)
Press button 5
to activate the air
conditioning.
The indicator lamp comes on.

Automatic control inactive
The air conditioning system is no longer
controlled automatically.

2
COMFORT

Personalisation of the Exterior
air intake/Interior air recirculation
function
This function is controlled automati-
cally. However, you can deactivate its
automatic control if you wish to change
the air intake mode at any time.

Changing the status
Press the Air intake/Interior air recircu-
lation button for at least 10 seconds.
When the status changes from active to
inactive, three bleeps are heard and the
indicator lamp fl ashes three times.
When the status changes from inactive
to active, two bleeps are heard and the
indicator lamp fl ashes three times.

Automatic control active
If the air distribution adjustment dial and
the air fl ow adjustment dial are placed
in the "AUTO" position, the Air intake/
Interior air recirculation function is also
controlled automatically.
Windows and windscreen demisting/defrosting

Demisting/defrosting


1.
Press button A
to select "exterior air
intake". The indicator lamp in this
button is goes off.

2.
Place the air distribution dial in the
"windscreen, side windows and
footwells" position.

3.
Select the air fl ow required.

4.
Select the temperature required.

5.
Press the "air conditioning on/off"
button B
to activate the air condi-
tioning. The indicator lamp in this
button comes on.

Rapid demisting/defrosting


1.
Place the air distribution dial in the
"windscreen and side windows" po-
sition.

2.
Select maximum air fl ow.

3.
Select maximum temperature.



Automatic control inactive
Even if the air distribution adjustment
dial and the air fl ow adjustment dial are
placed in the "AUTO" position, the Air
intake/Interior air recirculation function
is no longer controlled automatically.
The settings are retained, even
after switching off the ignition.

3
ACCESS
The electric window switches
can be confi gured via the colour
screen "Equipment" menu.
The electric window switches
remain operational for approxi-
mately 30 seconds after the igni-
tion is switched off and the switch
on the driver's door remains op-
erational for a further 30 seconds
when the door is opened.
The windows can no longer be
opened or closed after the driver's
door is closed.
The rear windows do not lower
fully.
ELECTRIC WWINDOWS


1.
Driver's electric window switch.


2.
Passenger's electric window
switch.


3.
Rear right electric window
switch.


4.
Rear left electric window switch.


5.
Deactivating

the passenger and
rear electric window switches.


In the event of unwanted open-
ing of the window on closing (for
example in the presence of frost),
reinitialise the electric windows
(refer to the corresponding para-
graph).
Safety anti-pinch
In automatic mode, when the window
rises and meets an obstacle, it stops
and lowers again.

Operation

With the ignition on, you have two op-
tions:


- manual mode



)
Press the switch gently to open or
pull it gently to close. The window
stops as soon as the switch is re-
leased.



- automatic mode



)
Press the switch fully to open or
pull it fully to close. The window
opens or closes completely when
the switch is released.

)
Pressing the switch again stops
the movement of the window.

System which opens or closes a window
manually or automatically. It is fi tted with
a system which provides protection if an
obstacle is detected on one-touch mod-
els and a deactivation system to prevent
misuse of the rear controls.

4
VISIBILITY

B.
rear wiper selection ring:
park.
intermittent wipe.
wipe with screen wash.

Rear wiper
The wiper wipes twice then switches to
intermittent mode with an interval of a
few seconds.
Keep the ring in this position to operate
the screen wash with several wipes of
the wiper.
The intermittence of the rear wiper
can be confi gured via the colour
screen "Equipment" menu.














Automatic rain sensitive wipers

The windscreen wipers operate automat-
ically, without any action on the part of
the driver, if rain is detected (sensor be-
hind the rear view mirror), adapting their
speed to the intensity of the rainfall.

Activation


)
Move the stalk A
to the "AUTO"
po-
sition.
A message appears on the multifunc-
tion screen.

Deactivation


)
Move the stalk A
to the "OFF"
posi-
tion.
A message appears on the multifunc-
tion screen.
Operating fault
Do not cover the rain sensor, linked
with the sunshine sensor and located in
the centre of the windscreen behind the
rear view mirror.
Switch off the automatic rain
sensitive wipers when using an
automatic car wash.
To protect the rubber of the wiper,
it is advisable to deactivate the
automatic mode when the vehicle
is parked and when the ambient
temperature is below 0 ° C.
In winter, it is advisable to wait
until the windscreen is completely
clear of ice before activating the
automatic rain sensitive wipers.

7
DRIVING

Stopping - Starting on a slope


Do not use the accelerator pedal to
immobilise the vehicle on a slope,
apply the parking brake instead.

When starting on a slope, accelerate
gradually while releasing the parking
brake.


Switching to sequential mode

Once you have moved off, you can
switch to sequential mode by selecting
position +/-
.

"D"
disappears and the gears engaged
appear in succession in the instrument
panel screen.
The gear change requests are only car-
ried out if the engine speed permits it.
Take your foot off the accelerator pedal
gently to engage the gear.

Switching to automated mode


Automated mode
After using the sequential mode, you
can return to the automated mode by
selecting position D
.

"D"
appears in the instrument panel
screen.
The gearbox then operates in auto-active
mode, without any action on the part of
the driver.
It continuously selects the gear most
suited to the conditions of:


- driving style,

- road characteristics,

- vehicle load.
To optimise driving comfort and obtain
the most suitable gear, avoid sharp vari-
ations in the pressure on the accelerator
pedal.

Auto sequential mode
In the automated mode, you can take
over control temporarily at any time
using the steering mounted controls.
The use of these controls permits manual
selection of the gears in situations which
require a faster changedown than that
offered in automated mode (arrival at a
roundabout, exit from a car park with a
steep gradient, overtaking...).
Stopping the vehicle

Before switching off the engine, you can:


- move to position N
to leave the
gearbox in neutral.

- leave a gear engaged, such as fi rst
or reverse.
In both cases, you must apply the parking
brake to immobilise the vehicle.


Operating anomaly

With the ignition on, if the message "Slow down"
or "Maintenance required"
ap-
pears in the multifunction screen, this in-
dicates a gearbox malfunction.
When a message is displayed, carry
out the following operations:


- slow down and stop your vehicle in
a safe place,

- place the lever in position N
and let
the engine run,

- open the bonnet to allow the engine
to cool.
If the message disappears for a long
period, you can set off again.
If the message remains displayed or ap-
pears frequently, contact a PEUGEOT
dealer or a qualifi ed workshop without
delay.
Press the brake pedal fi rmly
while starting the engine.

Start the engine. "N"
appears in the in-
strument panel screen.
Select fi rst gear (position D
or +/-
) or
reverse (position R
).
Release the parking brake.
Release the brake pedal then accelerate.

"D"
or "1"
or "R"
appear in the instru-
ment panel screen. The gearbox engages the gear re-
quested if the engine speed permits it.
The gear engaged appears.
To return to the automated mode, press
the back of the "+/OFF"
control for ap-
proximately 2 seconds.
At low speeds, when approaching a
stop or traffi c lights for example, the
gearbox changes down to fi rst gear au-
tomatically.

7
DRIVING
DCS GEARBOX DCS GEA
The six-speed electronically controlled
gearbox offers a choice between the
comfort of automatic regulation or the
pleasure of manual gear changing.
This gearbox has three driving modes:


- a manual
mode for changing of the
gears by the driver using the steering
mounted controls or the gear lever,

- a " Normal
" automatic mode for eco-
nomical control of the gears (everyday
use),

- a " Sport
" automatic mode which
permits a more dynamic style of
driving, with improved acceleration
and optimised engine braking.


Displays in the instrument
panel
When you move the lever in the gate
to select a position, the corresponding
indicator or message is displayed in the
instrument panel.

P.
Park.

R.
Reverse.

N.
Neutral.

D.
Drive (Automatic mode).

NORMAL.
Normal mode.

SPORT.
Sport mode.

1,2,3,4,5,6.
Gear engaged during manual
operation.


Gear lever positions


P
: park.
With your foot on the brake,
this position permits starting of
the vehicle.
To exit position P
, raise the ring on the
gear lever.

R
: reverse gear.
With the vehicle stationary, keep your
foot on the brake pedal and push the
gear lever forwards.

N
: neutral.
With your foot on the brake, this position
also permits starting of the vehicle.

D
: automatic mode.
Move the lever rearwards.

+/-
: manual mode with gear changing
using the lever.

7
DRIVING

"Normal" automatic mode


Select position D
.

"D"
appears in the instrument panel
screen.
The gearbox then operates in automatic
mode, without any action on the part of
the driver.
To optimise driving comfort and obtain
the most suitable gear, avoid sharp vari-
ations in the pressure on the accelerator
pedal.

"Temporary" manual mode
In automatic mode, you can take control
temporarily at any time using the steer-
ing mounted controls.
The use of these controls permits manual
selection of the gears in situations which
require a faster change down than that
offered in automatic mode (arrival at a
roundabout, exit from a car park with a
steep gradient, overtaking...).
The gearbox engages the gear re-
quested if the engine speed permits it.
The gear engaged appears.
To return to the automatic mode, press
the back of the "+/OFF"
control for at
least 2 seconds.



"Sport" automatic mode

From automatic mode, you can engage
"Sport" mode.
With the vehicle moving or stationary,
push the thumb wheel A
forward.

"SPORT"
appears in the instrument
panel screen.

Switching off "Sport" automatic
mode
You can return to "Normal" automatic
mode at any time:
Push the thumbwheel A
rearward once.



Stopping the vehicle

Before switching off the engine, you
must engage position P
or N
to place
the gearbox in neutral.
You must apply the parking brake to im-
mobilise the vehicle.
The gear lever must be in position P
to
remove the ignition key.


Hill start assist

To assist you when starting on a gradi-
ent, your vehicle is fi tted with a system
which immobilises it briefl y (approxi-
mately 2 seconds), the time required to
move your foot from the brake pedal to
the accelerator pedal. This function is
only active when the vehicle has been
completely immobilised with your foot
on the brake pedal and on certain gra-
dients.

Do not get out of the vehicle during
the hill start assist temporary immo-
bilisation phase.

To immobilise the vehicle on a gradient
for a longer period, you must use the
parking brake, not the accelerator.
When starting on a gradient, accelerate
gradually while releasing the parking
brake.