2011 Peugeot 308 SW BL warning

i
23
INSTRUMENTS and CONTROLS












PETROL - DIESEL MANUAL OR 6-SPEED ELECTRONIC GEARCONTROL OR AUTOMATIC GEARBOX INSTRUMENT PANELS

Panel grouping together the vehicle
operation indication dials and warning
lamps.
5.
Small screen.


6.
Central screen.


7.
Control button.


Starts a manual CHECK and
recalls the service information.
Resets the function to zero (trip
distance recorder or service
indicator).

8.
Instrument panel lighting button.


Adjusts the brightness of the
lighting of the instruments and
controls.


Dials



1.
Rev counter.


Indicates the speed of rotation of
the engine (x 1 000 rpm).

2.
Coolant temperature.


Indicates the temperature of the
engine coolant (° Celsius).

3.
Fuel level.


Indicates the quantity of fuel
remaining in the tank.

4.
Vehicle speed.


Indicates the current speed of the
moving vehicle (mph or km/h).

A.
Trip distance recorder.


(miles or km)

B.
Distance recorder.


(miles or km)

C.
Engine oil level indicator,


service indicator.


(miles or km)
These two functions are displayed
when the ignition is switched on,
then disappear after a few seconds.
Displays
For more information, refer to the
paragraph which relates to the but-
ton or function and its associated
display. The following functions are displayed
depending on the selection.


- Warning lamps/CHECK.


- Tyre under-infl ation detection.


- Speed limiter/Cruise control.


- Gear change indicator.


- 6-speed electronic gear control
or automatic gearbox.


- Navigation - Guidance/Trip
computer.

i
24
INSTRUMENTS and CONTROLS












PETROL - DIESEL MANUAL OR 6-SPEED ELECTRONIC GEAR CONTROL ORAUTOMATIC GEARBOX PEUGEOT CONNECT MEDIA INSTRUMENT PANELS


Dials



1.
Rev counter.


Indicates the speed of rotation of
the engine (x 1 000 rpm).

2.
Coolant temperature.


Indicates the temperature of the
engine coolant (° Celsius).

3.
Fuel level.


Indicates the quantity of fuel
remaining in the tank.

4.
Vehicle speed.


Indicates the current speed of the
moving vehicle (km/h or mph).

A.
Trip distance recorder.


(miles or km)

B.
Distance recorder.


(miles or km).

C.
Engine oil level indicator,


service indicator.


(miles or km)
These two functions are displayed
when the ignition is switched on,
then disappear after a few seconds.
The following functions are displayed
depending on the selection.


- Warning lamps/CHECK.


- Tyre under-infl ation detection.


- Speed limiter/Cruise control.


- Gear shift indicator.


- 6-speed electronic gear control
or automatic gearbox.


- Navigation - Guidance/Trip
computer.


- Vehicle parameters.





Panel grouping together the vehicle
operation indication dials and warning
lamps.
Displays

5.
Small screen.


6.
Central screen.


7.
Control button.


Starts a manual CHECK and
recalls the service information.
Resets the function to zero (trip
distance recorder or service
indicator).

8.
Instrument panel lighting button.


Adjusts the brightness of the
lighting of the instruments and
controls.
For more information, refer to the
paragraph which relates to the but-
ton or function and its associated
display.

!
26
INSTRUMENTS and CONTROLS
The warning lamps may come on
continuously or fl ash.
Certain warning lamps may come
on in two different modes. Only by
relating the type of lighting to the
operating status of the vehicle can
it be ascertained whether the situ-
ation is normal or whether a fault
has occurred.










Indicator and warning lamps

Visual indicators informing the driver
that a system is in operation (operation
or deactivation indicator lamps) or of the
occurrence of a fault (warning lamp).

Associated warnings
The switching on of certain warning
lamps may be accompanied by an au-
dible signal and a message on the mul-
tifunction screen.
Operation indicator lamps
If one of the following indicator lamps
comes on, this confi rms that the corre-
sponding system has come into opera-
tion.

Left-hand direction indicator.

Parking brake applied.

Right-hand direction
indicator.
Main beam headlamps.
Dipped beam headlamps.


Diesel engine pre-heating.
Wait until this has gone out be-
fore operating the starter.

Front foglamps.
When the ignition is switched on
The warning lamps come on for a few
seconds when the vehicle's ignition is
switched on.
When the engine is started, these warning
lamps should switch off.
If they remain on, before moving off,
consult the warning lamp concerned.
Common operation indicator lamps

Rear foglamp.

28
INSTRUMENTS and CONTROLS


Deactivation warning lamps
If one of the following warning lamps
comes on, this confi rms that the corre-
sponding system has been switched off
intentionally.



Passenger's airbag system
deactivation.
The passenger's airbag system
is put into service automatically
when the vehicle is started.
A specifi c control switch, located on the
passenger's side of the dashboard, per-
mits deactivation of the system. This is
confi rmed by continuous lighting of this
warning lamp on the instrument panel
or on the seat belt and passenger's
front airbag warning lamps display.


Dynamic stability control
(ESP/ASR) deactivation

The ESP/ASR system is put
into service automatically when
the vehicle is started.
A specifi c button, located on the dash-
board, permits deactivation of the sys-
tem. This is confi rmed by continuous
lighting of this warning lamp and of the
indicator lamp on the button.
From approximately 30 mph (50 km/h),
the system is reactivated automatically.


Common deactivation warning
lamps

Specifi c deactivation warning lamps
Automatic locking.
If this is displayed, it indicates
that you have deactivated the
automatic locking of the doors
and boot while driving.



Automatic rain sensitive
windscreen wipers.
If this is displayed, it indicates that
you have deactivated automatic
rain sensitive windscreen wipers. The other warning lamps appear on the
large screen, located in the centre of
the instrument panel.


Speed limiter.

If this is displayed, it indicates
that you have deactivated the
speed limiter.


Cruise control.

If this is displayed, it indicates
that you have deactivated the
cruise control.



Automatic illumination of
headlamps.

If this is displayed, it indicates
that you have deactivated auto-
matic illumination of headlamps.

!
29
INSTRUMENTS and CONTROLS
When the engine is running or the ve-
hicle is moving, the lighting of one of the
following warning lamps indicates the
occurrence of a fault requiring interven-
tion on the part of the driver.

Central alert.
Lighting is associated with
the displaying of another
warning lamp:


- punctured wheel,

- braking,

- power steering,

- engine oil pressure,

- coolant temperature,
stop the vehicle as soon as it is safe to
do so.

Service.
If this comes on, it indicates the
occurrence of a problem in one
of the systems which does not
have a specifi c warning lamp.
To identify the problem, consult the
message on the multifunction screen.
Braking.
If this comes on, it indicates the
occurrence of a fault in one of
the braking systems:


- signifi cant drop in the brake fl uid
level,

- electronic brake force distribution
(EBFD) faulty (simultaneous
lighting of the ABS warning lamp),
stop the vehicle as soon as it is safe to
do so.
When the vehicle is moving, check that
the parking brake is fully released. Any fault resulting in the displaying
of a warning lamp must be investi-
gated further by reading the associ-
ated message on the multifunction
screen.
In the event of diffi culty, do not
hesitate to contact a PEUGEOT
dealer.









Warning lamps

Common warning lamps After checking:


- that the doors, boot, the rear
screen and bonnet are closed,

- the engine oil level,

- the screenwash fl uid level,

- the remote control battery,

- the pressure of the tyres,

- the end of saturation of the particle
emission
fi lter (Diesel),
for any other situations, contact a
PEUGEOT dealer.

Anti-lock braking system
(ABS).

If this comes on, it indicates the
occurrence of a fault in the anti-
lock braking system.
However, this does not prevent op-
eration of the vehicle's servo-assisted
braking.

!
30
INSTRUMENTS and CONTROLS


Engine autodiagnostics
system.

If this comes on, it indicates the
occurrence of a fault in the en-
gine management system.
If it fl ashes, it indicates the occurrence
of a fault in the emission control system.

Maximum coolant
temperature.
If this comes on, it indicates that
the temperature in the cooling
system is too high. Stop the vehicle as
soon as it is safe to do so.
Low fuel level.
When this fi rst comes on, you
have approximately 6 litres
of
fuel remaining in the tank.
Refuel as soon as possible to avoid run-
ning out of fuel.
Until suffi cient fuel has been added,
this warning lamp comes on again each
time the ignition is switched on, along
with an audible signal and a message.
According to version, this audible signal
and this message are repeated, at in-
creasingly shorter intervals as the level
decreases towards "0"
.
Capacity of the tank: approximately
60 litres
.

Door open.
A door, the boot or the rear
screen is open:
Battery charge.
If this comes on, it indicates
the occurrence of a fault in the
battery charging circuit (dirty or
loose terminals, slack or cut alternator
belt...).
Engine oil pressure.
If this comes on, it indicates the
occurrence of a fault in the en-
gine lubrication system. Stop the
vehicle as soon as it is safe to do so.

Specifi c warning lamps


Dynamic stability control
(ESP/ASR).

The ESP/ASR system is put
into service automatically when
the vehicle is started.
Unless the system has been deactivat-
ed, if this warning lamp and the indicator
lamp on the button come on continuously,
this indicates the occurrence of a fault in
the ESP/ASR system or in the hill start
assist system.



- if the speed is below 6 mph
(10 km/h), this warning lamp
comes on continuously.

- if the speed is higher than 6 mph
(10 km/h), this warning lamp comes
on continuously, accompanied by
an audible signal.
Never continue to drive until you
run out of fuel, this could damage
the emission control and injection
systems.


Foot on brake.
On the 6-speed electronic gear
system gearbox, with the gear
lever in position N
, press the
brake pedal to start the engine.
On the automatic gearbox, with the en-
gine running, press the brake pedal to
release the gear lever and disengage
position P
.

i
!
31
INSTRUMENTS and CONTROLS
The display of certain warning
lamps may be accompanied by an
audible signal and a message on
the multifunction screen.

Specifi c warning lamps

The other warning lamps appear on the
large screen, located in the centre of
the instrument panel.
Depending on the seriousness of the
fault, they may be displayed in orange
or red. Certain warning lamps may be
linked with those of the instrument
panel.
If they are linked with the STOP

warning lamp, stop the vehicle as
soon as it is safe to do so.


Directional headlamps.
If this fl ashes, it indicates the
occurrence of a fault in the
directional headlamps system.

Service.

If this is displayed, it indicates the occur-
rence of a fault in one of the following:

Engine autodiagnostics
system.
If this is displayed, it indicates
the occurrence of a fault in the
engine management system.

Battery charge.
If this is displayed, it indicates
the occurrence of a fault in the
battery charging circuit (dirty or
loose terminals, slack or cut alternator
belt...).

- the engine management system,

- the emissions control system.

Airbags.

If this comes on, it indicates the
occurrence of a fault in one of
the airbag or seat belt preten-
sioner systems.

Seat belt not fastened/
unfastened.
If this comes on, it indicates
that the driver and/or the front
passenger has not fastened or has un-
fastened their seat belt. According to
version and/or country, the unfastening
of the seat belt only may be detected for
the front passenger.
It also indicates that one or more rear
passengers have unfastened their seat
belt (only on the 2nd row individual rear
seats on the SW).



Water in diesel * .
If this comes on, it indicates the
presence of water in the diesel
fi lter.
There is a risk of damage to the injection
system on Diesel engines.


*
According to country.

!
32
INSTRUMENTS and CONTROLS

Airbags.

If this is displayed, it indicates
the occurrence of a fault in one
of the airbag or pretensioning
seat belt systems.

Braking.
If this is displayed, it indicates
the occurrence of a fault in one
of the braking systems:


- signifi cant drop in the brake fl uid
level,

- electronic brake force distribution
(EBFD) faulty (simultaneous
lighting of the ABS warning lamp).
Stop the vehicle as soon as it is safe to
do so.
If the vehicle is moving, check that the
parking brake is fully released.

Anti-lock braking system
(ABS).
If this is displayed, it indicates
the occurrence of a fault in the
anti-lock braking system.
However, this does not prevent op-
eration of the vehicle's servo-assisted
braking.

Door open.
A door, the boot or the rear
screen is open:
Parking brake.

If this is displayed, while the ve-
hicle is moving, it indicates that
the parking brake has not been
fully released.
Electronic immobiliser.
If this is displayed, it indicates
the occurrence of a fault in the
electronic engine immobiliser
system or that the remote control bat-
tery is fl at.
Fuel level.
When this fi rst comes on, you
have approximately 6 litres
of
fuel remaining in the tank
Refuel as soon as possible to avoid run-
ning out of fuel.
Until suffi cient fuel has been added,
this warning lamp comes on again each
time the ignition is switched on, along
with an audible signal and a message.
According to version, this audible signal
and this message are repeated, at in-
creasingly shorter intervals as the level
decreases towards "0"
.
Capacity of the tank: approximately
60 litres
.

Screenwash fl uid level.

If this is displayed, following an
action on the wiper stalk, it indi-
cates that the screenwash fl uid
level is low.
Fill the screenwash/headlamp wash fl uid
reservoir when you next stop.


-
if the speed is below 6 mph (10 km/h),
this warning lamp is displayed in orange,

- if the speed is higher than 6 mph (10 km/h),
this warning lamp is displayed in red.


Never continue to drive until you
run out of fuel, this could damage
the emissions control and injection
systems.
Engine oil pressure.

If this is displayed, it indicates
the occurrence of a fault in the
engine lubrication circuit. Stop
the vehicle as soon as it is safe
to do so.

Engine oil level.

If this is displayed, it indicates
that the engine oil level is too
low. Stop the vehicle as soon
as it is safe to do so.

Coolant temperature.

If this is displayed, it indicates
that the temperature in the cool-
ing system is too high. Stop the
vehicle as soon as it is safe to
do so.

Coolant level.

If this is displayed, it indicates
that the coolant level is too low.
Stop the vehicle as soon as it is
safe to do so.