2011 NISSAN GT-R display

Black plate (64,1)
Model "R35-N" EDITED: 2009/ 10/ 30
SETTING FREEWAY ENTRANCE/
EXITIt is possible to set the destination to an
entrance or exit of a freeway and have the
system calculate a route.1. Push.
2. Highlight [Next Page] and push .3. Highlight [Freeway Entrance/Exit] and push
. A character input screen is
displayed.
4. Enter the name of the freeway.
5. After finishing the entry, highlight [List] and
push .6. Highlight the freeway of the destination from
the list, and push .
7. Highlight [Entrance] or [Exit] and push
. A list screen is displayed.8. Select the preferred destination from the list.
The position of the selected location is
displayed in the preview on the right side
of the screen. Then, push .
2-38
Navigation

Black plate (65,1)
Model "R35-N" EDITED: 2009/ 10/ 30
INFO:
Select [By Distance] to sort the list by the
nearest distance.
9. The entire route is shown on the map. Highlight [Start] after confirming the location
of the displayed dest ination, and push
. The system sets the destination
to the selected location and starts calculat-
ing a route.
INFO:
Even after setting a destination, the location of
the destination can be adjusted, the route can
be stored, etc.“PROCEDURES AFTER SETTING DES-
TINATION” page 2-43
SETTING INTERSECTIONIt is possible to set an intersection of any two
streets as the destination and have the system
calculate a route.1. Push .
2. Highlight [Next Page] and push .
3. Highlight [Intersection] and push TER>. A character input screen is dis-
played.4. Enter the name of the 1st street.
After finishing the entry, highlight [List] and
push . A list screen is displayed.
Navigation
2-39

Black plate (66,1)
Model "R35-N" EDITED: 2009/ 10/ 30
5. Highlight a street as the 1st street from thelist and push . A character input
screen is displayed.6. Enter the name of the 2nd street. After finishing the entry, highlight [List] and
push . A list screen is displayed.
7. Highlight a street as the 2nd street from the
list and push .8. The entire route is shown on the map.
Highlight [Start] after confirming the location
of the displayed dest ination, and push
. The system sets the destination
to the selected location and starts calculat-
ing a route.
INFO:
Even after setting a destination, the location of
the destination can be adjusted, the route can
be stored, etc.“PROCEDURES AFTER SETTING DES-
TINATION” page 2-43
SETTING CITY CENTERIt is possible to set the center of a city as a
destination and have the system calculate a
route.1. Push .
2. Highlight [Next Page] and push .
2-40
Navigation

Black plate (67,1)
Model "R35-N" EDITED: 2009/ 10/ 30
3. Highlight [City Center] and push TER>. A character input screen is dis-
played.4. Enter the name of the city, highlight [List]
and push . A list screen is
displayed.
INFO:
Highlight [Last 5 Cities] and push TER> to display the last 5 cities recently set
as destinations.
5. Highlight the preferred destination from the list and push . The position of the
selected location is displayed in the preview
on the right side of the screen.
INFO:
Select [By Distance] to sort the list by the
nearest distance.
6. The selected destination is displayed at the center of the map. Highlight [Start] after
confirming the location of the displayed
destination, and push .
The system sets the destination to the
selected location and starts calculating a
route.
Navigation
2-41

Black plate (68,1)
Model "R35-N" EDITED: 2009/ 10/ 30
INFO:
Even after setting a destination, the location
of the destination can be adjusted, the route
can be stored, etc.“PROCEDURES AFTER SETTING
DESTINATION” page 2-43
SETTING POINT ON MAPIt is possible to set a location scrolled to on the
map as the destination and have the system
calculate a route.1. Scroll the map, place the cross pointer over the preferred location, and push .
INFO:
. The map scale should be adjusted to
search for a location more effectively.
. The point on the blinking road where the
center of the cross pointer is located can be set as a destination.
2. Highlight [New Dest.] and push
.
INFO:
For the items other than [New Dest.], refer to
“Map menu screen”.“Scrolled location map screen” page
2-19
3. The system sets the destination to the selected location and starts calculating a route.
INFO:
If a point on a freeway is set as the destination, a
confirmation message is displayed.
DELETE DESTINATIONIt is possible to delete a destination and all
waypoints that have already been set.1. Press .
2-42
Navigation

Black plate (69,1)
Model "R35-N" EDITED: 2009/ 10/ 30
2. Select [Delete Destination] and press TER>.3. A confirmation message is displayed. Select [Yes] and press .
The destination and the waypoints are
deleted.
INFO:
The deleted destination and waypoints are not
able to be reactivated.Setting by voice command
1. Push <
>on the steering wheel.
2. After the tone sounds, speak a command.
To delete a destination and all waypoints:
“Delete Destination” (Alternate Command
Mode)
PROCEDURES AFTER SETTING
DESTINATIONAfter performing a route search, the route
guidance can be immediately started. Also, it is
possible to confirm or change a route.Available items after setting destination
. [Start]:
Starts route guidance to the selected
destination.
“Starting route guidance” page 2-44
. [More Routes]:
Displays 3 alternative routes.“Selecting route” page 2-44 .
[Add/Route Info]:
Displays the route information. A destination
or a waypoint can also be added.
“Confirming route” page 2-45
. [Move Location]:
Displays a map screen. The location of the
destination can be adjusted.“Moving location of destination” page
2-46
. [Store Location]:
Stores the location in the Address Book.“Storing location” page 2-47
. [Place Info]:
Displays information about the facility that
has been set as the destination, if it is
included in the map data.“Viewing information about searched
location” page 2-47INFO:
. If no operations have been performed on the
system for several seconds, [Start] is auto-
matically selected, and the system starts
route guidance.
. When using waypoints, [More Routes] is
disabled. After the route is started, push
then select [Edit/Add to
Route] to change the route between each
waypoint.
Navigation
2-43
ROUTE GUIDANCE

Black plate (70,1)
Model "R35-N" EDITED: 2009/ 10/ 30
“Editing route” page 2-55
. Even if the map screen is touched or
directional buttons other than the up or
down button are pushed, the same map
screen as when [Move Location] is selected
is displayed.
Starting route guidance1. Highlight [Start] and push .
Route guidance starts.
Selecting route1. Highlight [More Routes] and push TER>.2. Highlight the preferred route condition and push .
3. The display automatically returns to the map screen. Available route conditions
.
[Short. Time] (purple):
Prioritizes by the shortest time.
. [Min. Freeway] (orange):
Minimizes the use of freeways.
. [Short. Dist.] (green):
Prioritizes by the shortest distance.
INFO:
. When the route is selected, a preview is
displayed on the right side of the screen.
. The 3 routes may not always be different.
2-44
Navigation

Black plate (71,1)
Model "R35-N" EDITED: 2009/ 10/ 30
Confirming route1. Highlight [Add/Route Info] and push TER>.
2. Highlight the preferred information item and push .
3. Push to return to the previous
screen.
Available information
. [Turn List]:
Displays the details of the suggested route.
“Using turn list” page 2-60
. [Preview]:
The system will trace the planned route
going forward or in reverse.“Using route preview” page 2-61
. [Add Way Pt.]:
Edits the route by adding a waypoint or a
destination.“Adding destination or waypoint” page
2-45
. [Store Route]:
Stores a calculated route. A maximum of 5
routes can be stored. Stored routes can be
easily retrieved and set as the suggested
route.“STORING ROUTE” page 2-74
. [Map Scroll]:
Displays a map screen where the location of
the destination can be confirmed. Even if the
map screen is touched or directional buttons
other than the up or down button are
pushed, the same map screen as when
[Map Scroll] is selected is displayed.
Adding destination or waypoint:Before starting route guidance, destinations
and/or waypoints can be added. A total of 6
destinations or waypoints can be set.1. Highlight [Add Way Pt.] and push TER>.2. Set additional destinations or waypoints and push .
The method of searching for a location is the
same as the one for a destination.
“SETTING DESTINATION” page 2-23
Navigation
2-45