Keyless entry system*
E00300302085
Press the remote
control switch, and all doors (in-
cluding the backdoor) will be locked or unlocked
as desired. It is also possible to operate the outside
rear-view mirrors. 1- LOCK switch
2- UNLOCK switch
3-
Indication lamp
To lock
Press
the LOCK switch (1), and all doors (includ-
ing the backdoor) will be locked. When they are
locked with the room lamp switch at the middle po-
sition (DOOR), the room lamp and the turn-signal
lamps blink once.
To unlock
Press the UNLOCK switch (2), and all doors (in-
cluding the backdoor) will be unlocked. When they
are unlocked with the room lamp switch at the mid-
dle position (DOOR), the room lamp will be turned
on for approximately 15 seconds and the turn-sig-
nal lamps will blink twice. NOTE
l The
indication lamp
(3) comes on each time
a switch is pressed.
l If the UNLOCK switch (2) is pressed and no
door (including the backdoor) is opened with-
in approximately 30 seconds: relocking will
automatically occur.
l It is possible to modify functions as follows:
For further information, please contact your
MITSUBISHI MOTORS Authorized Service
Point.
• The time for automatic relocking can bechanged.
• The confirmation function (blinking of the turn-signal lamps) can be set to oper-
ate only when the doors and backdoor are
locked or only when the doors and back-
door are unlocked.
• The confirmation function (this indicates locking or unlocking of the doors and
backdoor with the blink of the turn-signal
lamps) can be deactivated.
• The number of times the turn-signal lamps are flashed by the confirmation
function can be changed.
Operation of the outside rear-view mir-
rors
To fold
Within 30 seconds of locking the doors and back-
door using the LOCK switch (1), press the LOCK
switch twice rapidly to fold the outside rear-view
mirrors. To extend
Within 30 seconds
of unlocking the doors and back-
door using the UNLOCK switch (2), press the UN-
LOCK switch twice rapidly to return the outside
rear-view mirrors to their extended positions.
NOTE
l The keyless entry system does not operate in
the following conditions:
• The key is left in the key cylinder.
• The door (including the backdoor) is open.
l The remote control switch will operate with-
in approximately 4 m from the vehicle. How-
ever, the operating range of the remote con-
trol switch may change if the vehicle is loca-
ted near a power station, or radio/TV broad-
casting station.
l If either of the following problems occurs,
the battery may be exhausted.
• The remote control switch is operated atthe correct distance from the vehicle, but
the doors (including the backdoor) are
not locked/unlocked in response.
• The indication lamp (3) is dim or does not come on.
For further information, please contact
your MITSUBISHI MOTORS Author-
ized Service Point. If you replace the bat-
tery yourself, refer to “Procedure for re-
placing the remote control switch bat-
tery” on page 1-05.
l If your remote control switch is lost or dam-
aged, please contact your MITSUBISHI
MOTORS Authorized Service Point for a re-
placement remote control switch. Locking and unlocking
1-04
1
OBKE12E1
Backdoor stopper
Open the
backdoor
fully and then move the locking
tube (A) to the LOCK position (B); this will ensure
that the backdoor remains in the fully opened posi-
tion. To subsequently release the stopper, move the
locking tube back to the UNLOCK position (C). CAUTION
l
When closing the
backdoor, be careful
not to trap your hands.
l Before closing the backdoor, make sure
that the locking tube (A) is in the UN-
LOCK position (C). Closing the back-
door with the locking tube (A) in the
LOCK position (B) may damage the back-
door stopper, rendering the backdoor un-
able to be closed. Security alarm system*
E00301500657
The security alarm
system is designed to prevent un-
lawful entry into the vehicle. It will alert people
nearby if a door, the backdoor, or the bonnet is
opened when the vehicle has not been unlocked us-
ing the keyless entry system.
Also, the alarm will be activated if any of the fol-
lowing occur.
l Attempt an unlawful moving of the vehicle.
(the vehicle inclination detection function)
l Detect a motion in the vehicle. (the interior
intrusion detection function)
l Disconnect the battery terminal.
The security alarm system is set to “active” when
the vehicle leaves the factory.
When making changes to the settings, please fol-
low the procedure listed in the section titled “Chang-
ing the system settings” on page 1-11. CAUTION
l
Do not
modify
or add parts to the securi-
ty alarm system.
Doing so could cause the security alarm
to malfunction.
NOTE l The
alarm system
will not be activated if the
doors (including the backdoor) have been
locked using a key or the central door lock
switch (instead of the keyless entry system). l
If the
turn-signal
lamps do not blink after the
locking and unlocking operation using the
keyless entry system, the security alarm sys-
tem may be malfunctioning.
Have the vehicle inspected at a
MITSUBISHI MOTORS Authorized Service
Point.
l In the following situations, the security
alarm system could be more likely to be acci-
dentally activated.
• Using a car wash
• Taking the vehicle on a ferry
• Parking in an automated car park
• Leaving someone or a pet in the vehicle
• Leaving a window, door, or the sunroofopen
• Leaving an unstable object such as a stuf- fed toy or accessory in the vehicle
• Suffering a continuous impact or vibra- tion by hail, thunder, etc.
l The sensitivity of the vehicle inclination de-
tection function and the interior intrusion de-
tection function can be adjusted. For details,
please contact a MITSUBISHI MOTORS Au-
thorized Service Point. Locking and unlocking
1-10
1
OBKE12E1
