Page 478 of 514
Vehicle care and maintenance
7-51
7
To reinstall1. Reverse the above removal procedure.
2. When installing the cover, start by fitting the two clips
closest to the outside of the vehicle (the clips numbered 1
and 2 in the illustration) in the order of the numbers.
When fitting the clips, grasp the bottom edge of the cover
and pull it toward the rear of the vehicle to align the clip
holes in the cover with those in the body.
When reinstalling the clips of the cover, push the pin (F).
3. Fit the remaining four clips and the one screw.
Rear combination lights
N00943700373
1. Remove the screws (A) that hold the light unit.
BK0121600US.book 51 ページ ２０１０年４月１２日 月曜日 午前１０時３９分
Page 479 of 514
7-52 Vehicle care and maintenance
7
2. Move the light unit toward the rear of the vehicle and
remove the clips (B).3. Remove each socket and bulb assembly by turning it
counterclockwise.
C- Tail and stop and rear side-marker light
Remove the bulb from the socket by turning it counterclock-
wise while pressing in.
D- Back-up light
Remove the bulb by pulling it out.
E- Rear turn signal light
Remove the bulb from the socket by turning it counterclock-
wise while pressing in.
BK0121600US.book 52 ページ ２０１０年４月１２日 月曜日 午前１０時３９分
Page 480 of 514
Vehicle care and maintenance
7-53
7
4. To install the bulb, perform the removal steps in reverse.NOTEWhen mounting the light unit, align the clips (F) on the
light unit with the hole in the body.
License plate lights
N00944000315
1. When removing the light unit (A), push it toward the left
side of the vehicle body.
BK0121600US.book 53 ページ ２０１０年４月１２日 月曜日 午前１０時３９分
Page 482 of 514
Vehicle care and maintenance
7-55
7
NOTEWhen mounting the light unit, insert tab (C) first then
align tab (D) with its hole.
Dome light (front)
N00944100286
1. Insert a screwdriver into the notch of the light assembly.
Pry gently to remove the lens, then remove the bulb from
the light holder. NOTEWrap a cloth around the tip of the screwdriver to keep
from scratching the lens.
2. To install the bulb, perform the removal steps in reverse.Reading lights
N00944400090
Have the reading light bulbs replaced at an authorized Mitsub-
ishi Motors dealer or a repair facility of your choice.
BK0121600US.book 55 ページ ２０１０年４月１２日 月曜日 午前１０時３９分
Page 483 of 514
7-56 Vehicle care and maintenance
7
Rear personal lights
N00944700080
1. Insert the tip of a screwdriver at the edge of the lens, pry
gently to remove the lens, and then remove the bulb from
the light holder.NOTEWrap a cloth around the tip of the screwdriver to keep
from scratching the lens.
2. To install the bulb, perform the removal steps in reverse.
Luggage room light
N00944900079
1. Insert a screwdriver into the notch of the light assembly
and pry gently to remove the lens. Pull the light bulb out
from the light holder.NOTEWrap a cloth around the tip of the screwdriver to keep
from scratching the lens.
2. To install the bulb, perform the removal steps in reverse.
BK0121600US.book 56 ページ ２０１０年４月１２日 月曜日 午前１０時３９分
Page 484 of 514
Vehicle care and maintenance
7-57
7
Door lights
N00945000077
1. Insert the tip of a screwdriver at the edge of the lens, pry
gently to remove the lens. Pull the bulb from the light
holder.NOTEWrap a cloth around the tip of the screwdriver to keep
from scratching the lens.
2. To install the bulb, perform the removal steps in reverse.
Vehicle care precautions
N00945100153
In order to maintain the value of your vehicle, perform regular
maintenance using the proper materials and procedures. Be
sure to use only those materials and procedures that meet your
local environmental pollution control regulations. Choose the
materials you will use carefully, to be sure that they do not con-
tain corrosives. If you are not sure, contact an authorized Mit-
subishi Motors dealer for help in choosing these materials.
CAUTION
!Cleaning products can be dangerous. Some are poi-
sonous. Others are highly flammable. Some are dan-
gerous if you breathe their fumes in a closed space.
When you use anything in a container to clean your
vehicle, be sure to follow the instructions. Always
open your vehicle doors or windows when you’re
cleaning the inside. Never use the following chemi-
cals to clean your vehicle:
• Gasoline
• Carbon Tetrachloride
• Benzine
• Kerosene
• Naphtha
• Acetone
• Turpentine
• Paint Thinner
• Lacquer Thinner
• Nail Polish Remover
BK0121600US.book 57 ページ ２０１０年４月１２日 月曜日 午前１０時３９分
Page 485 of 514
7-58 Vehicle care and maintenance
7
These can all be dangerous, and they all can damage your vehi-
cle.
Cleaning the inside of your vehicle
N00945200037
After washing the inside of your vehicle with any cleaner, wipe
it dry in a shady, well ventilated area. NOTEAlways read the instructions on the cleaner label.Plastic, vinyl leather, fabric and flocked parts
N00945300041
1. Lightly wipe these off with a soft cloth soaked in a 3%
solution of gentle soap and water.
2. Dip cloth in fresh water and wring out well. Using this
cloth, wipe off the detergent thoroughly.NOTEDo not use cleaners, conditioners, or protectants contain-
ing silicone or wax.
Such products may cause annoying reflections and
obscure vision.
CAUTION
!Do not use organic substances (solvents, kerosene,
alcohol, gasoline, etc.) or alkaline or acidic solutions.
These chemicals can cause discoloring, staining or
cracking of the surface.
If you use cleaners or polishing agents, make sure
their ingredients do not include the substances men-
tioned above.
BK0121600US.book 58 ページ ２０１０年４月１２日 月曜日 午前１０時３９分
Page 486 of 514
Vehicle care and maintenance
7-59
7
Upholstery
N00945500030
1. To maintain the value of your new vehicle, maintain the
upholstery carefully and keep the interior clean.
Use a vacuum cleaner and brush to clean the seats. If
stained, vinyl and synthetic leather should be cleaned with
an appropriate cleaner. Cloth fabrics can be cleaned with
either upholstery cleaner or a 3% solution of gentle soap
in lukewarm water.
2. Clean the carpeting with a vacuum cleaner and remove
any stains with carpet cleaner. Oil and grease can be
removed by lightly dabbing with a clean white cloth and
spot remover. NOTEIf fuzzing is difficult to remove from the seat upholstery,
draw a suitable defuzzing brush over the surface in one
direction.Genuine leather
(if so equipped)
N00945600217
1. To clean, lightly wipe the leather with a soft cloth soaked
in a 5 % solution of gentle soap and water.
2. To rinse, dip the cloth in fresh water, wring it out well, and
wipe off all the soap.
3. To preserve and protect, use a leather protecting agent on
the genuine leather surface. NOTEIf genuine leather is wet with water, wipe it with a dry,
soft cloth.
If left damp, mildew may grow and damage the leather
surface.The genuine leather surface can be damaged if brushed
with a nylon or synthetic fiber brush.
Organic solvents such as benzine, kerosene, alcohol, gaso-
line, acid or alkaline solvents can discolor the genuine
leather surface and should not be used.
Genuine leather can mildew if not kept clean. Clean up
any oil stains immediately.
The genuine leather surface may harden and shrink if it is
exposed to the direct sunlight for long hours. When your
vehicle is parked, place it in the shade as much as possi-
ble.
When the temperature of the vehicle interior rises in sum-
mer, vinyl products left on the genuine leather seat may
deteriorate and stick to the seat.
BK0121600US.book 59 ページ ２０１０年４月１２日 月曜日 午前１０時３９分
