2011 MERCEDES-BENZ SPRINTER jacking points

Speedometer ...................................
71
Tachometer ...................................... 71
Instrument cluster illumination
see Instrument lighting
....................72
Instrument lighting ............................. 72
Interior light Changing bulbs ......................238, 239
Interior lighting
Changing bulbs .............................. 233
Front ................................................ 92
Rear ................................................. 92
Interior motion sensor ........................62
ISOFIX (LATCH-type child seat
securing system) ................................. 43J
Jack ..................................................... 182
Jacking points ................................ 230
Preparation .................................... 230
Jump-starting ..................................... 247
Jump-starting connection point in
the engine compartment .................. 247K
Key Checking the batteries ..................... 53
Malfunction .................................... 217
Kickdown

........................................... 115L
Lamp Failure indicator ............................... 89
Language
Display (vehicles with steering
wheel buttons) ................................. 81
Lashing points and materials

...........146
Lashing points and tie downs Permissible tensile load ................. 283
License plate lamp
Changing bulbs ......................236, 237
Lighting
Bulb failure indicator ........................89
Changing bulbs ......................233, 234
Instrument ....................................... 72
Light switch ..................................... 89Lights
Automatic headlamp mode ..............90
Combination switch

.........................90
Cornering light function ...................91
Daytime running lamp
mode ................................... 74, 82, 89
Interior lighting ................................ 92
Light switch ..................................... 89
Load distribution ....................... 146, 152
Loading guidelines ............................144
Loads Securing ........................................ 146
Transporting .................. 144, 146, 152
Locator lighting
Setting (vehicles with steering
wheel buttons) ................................. 83
Locking
Automatic ........................................ 55
With button ...................................... 55
With key ........................................... 52
Locking system
see Central locking .......................... 54
Low-beam headlamps ......................... 89
Automatic headlamps ......................90
Changing bulbs .............................. 235
Daytime running lamp mode
(vehicles without steering wheel
buttons) ........................................... 74
Daytime running lamp mode
(vehicles with steering wheel
buttons) ..................................... 74, 82
Driving abroad ............................... 138 M
M+S tires ............................................ 254
Maintenance points under the
hood .................................................... 169
Malfunctions ...................................... 187
Message memory (vehicles with
steering wheel buttons)

...................78
Maximum speed ................................ 141
Menu (vehicles with steering
wheel buttons)
Audio ............................................... 77
Message memory ............................ 78
Operation ......................................... 76
Settings ........................................... 78 Index
9

!
Only use the jack pump lever middle rod
and the rod with the largest diameter as a
lug wrench extension.
Only slide the middle
rod as far as it will go onto the lug wrench.
The rods may otherwise bend and be
distorted to such an extent that they can
no longer be used as a pump lever for the
jack. X
Loosen the wheel nuts or wheel bolts on
the wheel to

be changed by about one turn
using extended lug wrench 0046. Do not
unscrew the wheel bolts or wheel nuts
completely.
Hydraulic jack X
Insert the third rod of the jack pump lever
into the lug wrench extension.
The jack pump lever is assembled. X
Close pressure release screw 0047.
X To do this, use the flattened section on
pump lever 0046 to turn pressure release
screw 0047 clockwise to the stop. i
Never turn pressure release screw 0047
more than 1 or 2 full turns. Hydraulic fluid
could otherwise escape.
X Insert pump lever 0046 into the
recess on the
jack and secure by turning it clockwise.
X Make sure that the jack is positioned
directly under the

jacking points described
below.
X Raise the vehicle by pumping the lever until
the wheel is raised clear of the ground.
Make sure that the distance between the
underside of the

tires and the ground does
not exceed 1.2 in (3 cm).
Jacking point at the front axle The vehicle jacking point is located under the
longitudinal member
in

front of the front axle. Jacking point at the rear axle
The jacking point is located under the
longitudinal member
in

front of the rear axle. Jacking point (example: vehicle type 2500)230
Wheels and tires
Practical advice

Jacking point (example: vehicle type 3500 )
!
Do not place
the jack on the leaf spring or
the differential case.
On cab chassis vehicles, the jacking point is
located next to the front leaf spring support. Jacking point (example: platform vehicle)
!
Only position the jack on the jacking
points intended for

this purpose. You could
otherwise damage the vehicle.
Removing a wheel X
Unscrew the wheel bolts or nuts.
! Do not place

the wheel bolts or the wheel
nuts in sand or dirt. The threads of the
wheel bolts and wheel nuts could otherwise
be damaged when being installed.
X On front wheels with wheel nuts, remove
the wheel nut cover.
X Remove the wheel. Mounting a new wheel G
Warning
To avoid the risk of serious or even fatal injury
and to avoid damage to the vehicle, observe
the following:
R replace the wheel bolts and wheel nuts if
they are damaged or have become rusty.
R never oil or grease wheel bolts or wheel
nuts.
R if a wheel

hub thread is damaged, you must
not drive the vehicle.
Consult a qualified specialist workshop
which has the necessary specialist
knowledge and tools to carry out the work
required.
For this reason, we recommend an
authorized Sprinter Dealer. In particular, all
work relevant to safety or on safety-related
systems must be carried out at a qualified
specialist workshop.
R For safety reasons, we recommend that you
only use wheel bolts and wheel nuts which
have been approved for Sprinter vehicles.
Other wheel bolts or wheel nuts could work
loose.
X Clean the wheel and wheel hub contact
surfaces.
X Push the wheel onto the wheel hub or the
adapter for the

spare wheel and press it on.
! If your vehicle is equipped with the tire
pressure monitor, each wheel has an
electronic component.
Tire-mounting tools should not be applied
in the area of the valve. Otherwise, the
electronic components could

be damaged.
Only have the tires changed at a qualified
specialist workshop, e.g. an authorized
Sprinter Dealer. G
Warning
Do not tighten the wheel bolts and wheel nuts
completely while the

vehicle is still jacked up.
The vehicle could otherwise tip. Wheels and tires
231
Practical advice Z