typicall
ywearm ore on the shoulders and the
rear tyres in the centre.
On vehicles that have the same size front and
rear wheels, yo ucan interchange the wheels
ever y5000kmto1 0,000 km depending on
the degre eoftyre wear. Do not reverse the
direction of tyre rotation.
Clea nthe con tact surface softhe wheel and
the brake disc thoroughly ever ytime awheel
is interchanged. Chec kthe tyr epressure and,
if necessary, restart th etyre pressure loss
warning syste morthe tyrepressure monitor.
! On vehicles fitted wit hatyre pressure
monitor, electronic components are loca-
ted in the wheel.
Tyre-fitting tools should not be applied in
the area of the valve, as this could damage
the electronic components.
Always have the tyres changed at aquali-
fied specialist workshop, e.g. aMercedes-
Benz Servic eCentre. Direction of rota
tion
Tyres with aspecified direction of rotation
have additional benefits, e.g. if there is arisk
of aquaplaning. You will only gain these ben-
efits if the correct direction of rotation is
observed.
An arrow on the sidewall of the tyre indicates
its correct direction of rotation.
You may fit an emergenc yspare wheel/spare
wheel against the direction of rotation.
Observe the tim erestric tion on use as well as
the speed limitation specified on the emer-
genc yspare wheel/spar ewheel. Storing wheels
Stor ewheels that ar enot being used in acool,
dry and preferably dar kplace. Protect the
tyres against oil, grease, petrol and diesel. Cleanin
gthe whee ls G
WARNING
Do not us ehigh-pressure cleaners with circu-
lar-jet nozzles (dirt grinders) to clean your
vehicle, in particular the tyres. You could oth-
erwise damage the tyres and cause an acci-
dent. Wheel and tyr
ecombinations Points to remember
! For safety reasons, Mercedes-Ben zrec-
ommends that you only use tyres and
wheels which have been approved by
Mercedes-Ben zspecifically for your vehi-
cle.
These tyres have been specially adapted
for use with the contro lsystems ,suc has
AB SorE SP®
,a nd are marked as follows:
R MO =Mercedes-Ben zOriginal
R MOE =Mercedes-Ben zOriginal Extended
(tyres with run-flat characteristics)
R MO1 =Mercedes-Ben zOriginal (only cer-
tain AMG tyres)
Mercedes-Benz Original Extended tyres
may only be use donwheels that hav ebeen
specifically approved by Mercedes-Benz.
Only use tyres, wheels or accessories tes-
ted and approved by Mercedes-Benz. Cer-
tain characteristics, e.g. handling, vehic le
nois eemis sions or fuel consumption, may
otherwise be adv ersely affected. In addi-
tion, when driving with aload, tyr edimen-
sion variations could cause the tyres to
come into contact with the bodywork and
axle components .This could result in dam-
age to the tyres or the vehicle.
Mercedes-Ben zaccept snoliability for
damag eresulting from the use of tyr es,
wheel soraccess orieso the rthan those tes-
ted and approved.
Further information about tyres, wheels
and approved combination scan be 364
Wheel and tyr
ecombinationsWheels and tyres
obtained from any Mercedes-Benz Service
Centre.
! Retreaded tyres ar eneither tested nor
recommended by Mercedes-Benz, since
previous damage can nota lways be detec-
ted on retreaded tyres. As aresult,
Mercedes-Benz can notg uarantee vehicle
safety if retreaded tyres are fitted. Do not
fit used tyres if you have no information
about their previous usage.
! Large wheels: the lower the section width
for acertain wheel size, the lower the ride
comfor tisonp oor roadsurfaces. Roll com-
fort and suspensio ncomfort ar ereduced
and the risk of damage to the wheels and
tyres as aresult of driving over obstacles
increases.
i You will fin datable of tyre pressures on
the inside of your vehicle's fuel filler flap.
For further information on tyre pressure,
see (Y page 359).
i Notes on the vehicle equipment –always
fit the vehicle:
R with tyre softhe sam esize on agiven axle
(left/right)
R with the same type of tyre satagiven
tim e(sum mertyres, winter tyres,
MOExtended tyres)
i Vehicles with MOExtended tyre sare not
equippe dwithaTIREFIT kit at th efactory.
It is therefore recommended that you addi-
tionally equip your vehicle with aTIREFIT kit
if yo ufit tyre sthat do not fea ture run-flat
prope rties, e.g. winter tyres. ATIREFIT kit
can be obtaine dfrom aMercedes-Benz
Servic eCentre.
i Overview of abbreviation sused in the fol-
lowin gtyre tables:
R BA: both axles
R FA: front axle
R RA: rear axle In the following table, the wheel/tyre combi-
nations are allocate
dtothe vehicle models
through variants, e.g. V1 ,V2etc.: V1
V2
V3
i
Not all wheel/tyre combinations can be
mounted at the factory in all countries. Wheel and tyr
ecombinations
365Wheels andtyres Z
ML 25
0BlueTEC 4MATIC
ML 350 4MATIC
ML 350 BlueTEC 4MATIC
?
Vehicl eidentification number (VIN)
A Maximum permissible gross vehicle
weight
B Gross combination mass
C Maximum permissible front axle load
D Maximum permissible rear axle load
E Paint code Vehicle identification number (VIN)
In addition to being stamped on the vehicle
identification plate, the vehicle identification
number (VIN) is also stamped onto the vehicle
body. It is located in the lower part of the
right-han dA-pillar. X
Ope nthe front right-hand door.
X Open cover :in the direction of the arrow
and remove it.
You will see the vehicle identification num-
ber (VIN). Engine number
The engin enumber is stamped into the crank-
case. More information can be obtained from
any Mercedes-Benz Service Centre. Service products and capacities
Important safety notes
Service products include the following:
R fuels (e.g. petrol, diesel)
R additives for exhaust gas aftertreatment
(AdBlue ®
)
R lubricants (e.g. engine oil, transmission oil)
R coolant
R brake fluid
R windscreen washe rfluid
Vehicle component sand thei rrespective
lubricants must match. Mercedes-Ben zrec-
ommends that you use products that have
been tested and specially approved by
Mercedes-Ben z.These product sare listed in
this Mercedes-Be nzOwner's Manual in the
relevant section.
You can recognise service product sapproved
by Mercedes-Ben zbythe fol lowinginscrip-
tion on the cont ainers:
R MB-Freigabe (e.g. MB-Freigabe 229.51)
R MB Approva l(e.g. MB Approval 229.51)
Other designation sorrecommendations
relat etoal evel of qualit yoras pecification in
accordance wit hanMBSheet number (such
as MB 229.5). They hav enot necessaril ybeen
approved by Mercedes-Benz.
You can obtain further information from any
Mercedes-Benz Ser vice Centre. G
WARNING
Whe nhandling, storing and disposing of any
servic eproducts, please observe th erelevant
regulations, as you could otherwise endanger
yourself and others.
Keep servic eproducts awa yfrom children.
To protect your health ,donot allow service
products to com einto contact with your eyes
or ope nwounds. See adoctor immediately if
any service product is swallowed. H
Environmental note
Dispose of service products in an environ-
men tally-responsible manner. Service products and capacities
373Technicaldata Z
Fuel
Important safety notes G
WARNING
Fuel is highly flammable. Fire, naked flames
and smokin gare therefore prohibi tedw hen
handlin gfuels.
Swit choff th eenginea nd the auxiliary hea ting
before refuelling. G
WARNING
Do not come int ocontact with fu els.
It is hazardous to your healt hifyour skin
comes int odirect contact wit hfuels or you
breathe in fuel vapours.
Tank capacity Total capacity
32 Of whic
hreserv efuel !
Do not use petrol to refuel vehicles with a
diesel engine. Do not use diesel to refuel
vehicles with apetrol engine. Even small
amounts of the wron gfuel result in damage
to the fuel system and the engine.
Further information on refuelling and on fuels
(Y page 152).
Notes on fuel consumption The vehicle will use more fuel than usua
lin
the follow ings ituations:
R at very low outside temperatures
R in urban traffic
R on short journeys
R when towing atrailer
R in mountainou sterrain
i Only for certain countries: you can find
the curren tconsumption and emission val-
ues of your vehicle in the COC documents (EU CERTIFICATE OF CONFORMITY). These
documents ar
edelivered with your vehicle.
The consumption figures were in each case
based on the currently applicable version:
R for vehicles up to and including the EURO
4s tandard ,inaccordanc ewithEUD irec-
tive 80/1268/ECC
R for vehicles above the EURO 5standard,
in accordance with Regulatio n(EC) No.
715/2007
Deviations from these value smay occur
under normal operating conditions.
! Do not use any fuel additives, as they can
cause malfunctions and engine damage. H
Environmental note
CO 2(carbon dioxide) is the gas which scien-
tists believe to be principally responsibl efor
global warmin g(the greenhouse effect). Your
vehicle's CO 2emissions are directly related
to fuel consumptio nand therefore depend on:
R efficient use of the fuel by the engine
R driving style
R othe rnon-technical factors, such as envi-
ronmental influences or road conditions
You can minimise your vehicle' sCO
2emis-
sions by driving carefull yand having it serv-
iced regularly. AdBlue
®
Important safety notes i
For BlueTEC vehicles only.
AdBlue ®
is an on-flammable, non-toxic, col-
ourless, odourless and water-soluble fluid.
! Surfaces which have com einto contact
with AdBlue ®
whil erefilling should be
rinsed immediately with water ,orremove
AdBlue ®
with amoist clot hand cold water.
If AdBlue ®
has alread ycrystallised, us ea
sponge and cold water to clean the area.
32 Missing value swere not available at time of going to print. 374
Service products and capacitiesTechnical data
Diesel engines MB Approval
228.51,
229.31 ,229.51 engine oils on the Interne
tat
http:/ /bevo. mercedes -benz.com by enter-
ing the designation, e.g. 22 9.5.
i If the engine oils listed in the table are not
available ,you ma yadd the followin gengine
oil su ntil the next oil change:
R vehi cles with apetrol engine: MB
Approval 22 9.1orA CEAA3
R vehicles wit hadiesel engine: MB
Approval 229.1 or ACE AC3
Engine oil may only be adde donce, and no
mor ethan 1. 0lmay be added.
Capacities The following values refer to an oil change
including the oil filter. Model Capacity
7.0 l
7.8 l
8.0 l
Additives
!
Do not use additive sinengine oil .This
could damage the engine.
Engine oil viscosity Viscosit
ydescribes the flow characteristi cs
of afluid. If an engin eoil has ahigh viscosity
rating, it flows slowly; the lower the viscosity,
the faster it flows.
Engine oil selection is based on the respective
outside temperatures and in accordance with
the SA Eclassification (viscosity). The table
below shows you which SA Eclassifications are to be used. The low-temperature proper-
ties of engin eoils can be significantly
impaired durin goperation due to, for exam-
ple, ageing or soot and fuel accretion. It is
therefore strongly recommende dtoobserve
regula roil changes using an approved engine
oil with the appropriate SA Eclassification. Brake fluid
G
WAR
NING
Over aperiod of time, the brak efluid absorbs
moisture fro mthe air ;This lower sits boiling
point.
If the boiling point of the brake fluid is too low,
vapour pockets may form in the brake system
when the brakes are applied hard (e.g. when
driving downhill). Thi simpairs brakin geffi-
ciency.
Yo us hould hav ethe brake fluid renewed at
regular intervals. The brake fluid change inter-
vals can be found in the Servic eBooklet.
Only use brak efluid approved by Mercedes-
Benz .Information abou tapproved brak eflu-
ids can be obtained from any Mercedes-Benz
Service Centr eoronthe Internet at
http://bevo. mercedes-benz.com
i There is usuall yanoticeint he engine
compartmen ttoremin dyou when the next
brake fluid change is due. 376
Service products and capacitiesTechnical data
You can cal
lupanoverview of ap proved
ML
350 BlueTEC 4MATIC
Vehicles wit
hadiesel particle filter
ML 250 BlueTEC 4MATIC
ML 350 4MATIC
ML 350 BlueTEC 4MATIC
ML
250 BlueTEC 4MATIC
Coolant
Important safety notes The coolan
tisamixture of water and anti-
freeze/corrosio ninhibitor. It performs the
following tasks:
R anti-corrosio nprotection
R antifreeze protection
R raising th eboiling point
i When the vehicle is first delivered, it is fil-
led with acoolant mixtur ethat ensures
adequate antifreeze and corrosion protec-
tion.
! Only add coolant that has been premixed
with the desired antifreeze protection. The
engin ecould otherwise be damaged.
Further information on coolants and on fill-
ing can be found in the Mercedes-Benz
Specifications for Servic eProducts ,MB
Approval 310.1 ,e.g. on the Internet at
http ://bevo.mercedes-benz.com .You can
also consult aMercedes-Benz Service
Centre.
! Alway suseasuitable coolant mixture,
even in countries where high temperatures
prevail.
Otherwise, the engine cooling system is not
sufficiently protected from corrosion and
overheating.
If antifreeze/corrosio ninhibitor is present in
the correc tconcentration, the boilin gpoint of
the coolant during operation will be around
13 0†.
The antifreeze/ corrosion inhibitor con centra-
tion in the engine cooling system should:
R be at leas t50%. This wil lprotect the engine
coolin gsystem agains tfreezin gdown to
around -3 7†.
R not excee d55% (antifreeze protection
down to -45 †);otherwise, heat will not be
dissipated as effectively.
If the vehicle has los tcoolant, top it up with
equal amount sofwater and antifreeze/cor- rosion inhibitor. Mercedes-Benz recom-
mends an antifreeze/corrosion inhibitor
which has been approved for Mercedes-Benz.
! The engin ecoolin gsystem is filled with
coolant that must be renewed after 15
years, or after 250,000 km at the lates t. Vehicl
edata
Pleas enotet hat for the speci fied vehicle
data:
R the height sspecified may var yasaresult
of:
- tyres
- load
- conditio nofthe suspen sion
- optional equipment
R item sofo ptional equipmen tincrease the
unlade nweight and reduc ethe maximum
payload. The unladen weight is speci fied in
accordanc ewith EC directive and includes:
- driver (68 kg)
- luggage (7 kg)
- all fluids (fuel tan k90% full)
R veh icle-specific weigh tinformation can be
found on the vehicl eidentification plate
(Y page 37 2).
R only for cer tain countries: you can find vehi-
cle-specific vehicle data in the COC docu-
ment s(CERTIFICATE OF CONFORMITY).
Thes edocuments ar edelivered with your
vehicle.
Missing values were not available at tim eof
going to print. All models
Vehicle lengt
h(ECE) 480
4mm Vehicle width
including exterior
mirrors
214
1mm Vehicle width with-
out exterior mirrors 192
6mm Vehicl
edata
377Techni caldata Z