2011 LEXUS RX350 remote control

428
3-7. Other interior features
nProgramming a Rolling Code system (for U.S.A. owners)
If your device is Rolling Code equipped, follow the steps under the
heading “Programming the HomeLink®” before proceeding with the
steps listed below.
Locate the learn button on the ceiling mounted garage door
opener motor. The exact location and color of the button may
vary by brand of garage door opener motor.
Refer to the operation manual supplied with the garage door opener
for the location of the learn button.
Press the learn button.
Following this step, you have 30 seconds in which to initiate step 3
below.
Press and hold the vehicle’s programmed HomeLink® button for
2 seconds and release it. Repeat this step once again. The garage
door may open.
If the garage door opens, the programming process is complete. If the
door does not open, press and release the button a third time. This third
press and release will complete the programming process by opening
the garage door.
The ceiling mounted garage door opener motor should now recognize
the HomeLink® signal and operate the garage door.
Repeat the steps above to program another rolling code system
for any of the remaining HomeLink® buttons.
nProgramming an entry gate (for U.S.A. owners)/Programming all
devices in the Canadian market
Place your transmitter 1 to 3 in. (25 to 75 mm) away from the sur-
face of the HomeLink®.
Keep the HomeLink® indicator light in view while programming.
Press and hold the selected HomeLink® button.
Repeatedly press and release (cycle) the device’s remote control
button for two seconds each until step 4 is completed.
When the indicator light on the HomeLink® compatible trans-
ceiver starts to flash rapidly, release the buttons.
STEP1
STEP2
STEP3
STEP4
STEP1
STEP2
STEP3
STEP4

430
3-7. Other interior features
Erasing the entire HomeLink® memory (all three programs)
Press and hold the 2 outside but-
tons for 10 seconds until the indi-
cator light flashes.
If you sell your vehicle, be sure to
erase the programs stored in the
HomeLink® memory.
nBefore programming
lInstall a new battery in the remote control transmitter.
lThe battery side of the remote control transmitter must be pointed away from
the HomeLink® button.
nCertification for the garage door opener
For vehicles sold in the U.S.A.
FCC ID: CB2070NHL4
NOTE:
This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
FCC WARNING:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
For vehicles sold in Canada
NOTE:
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interfer-
ence that may cause undesired operation of the device.
nWhen support is necessary
Visit on the web at www.homelink.com or call 1-800-355-3515.

431
3-7. Other interior features
3

Interior features
CAUTION
nWhen programming a garage door or other remote control device
The garage door or other device may operate, so ensure people and objects are
out of danger to prevent potential harm.
nConforming to federal safety standards
Do not use the HomeLink® compatible transceiver with any garage door opener
or device that lacks safety stop and reverse features as required by federal safety
standards.
This includes any garage door that cannot detect an obstruction object. A door or
device without these features increases the risk of death or serious injury.

497
4-3. Do-it-yourself maintenance
4

Maintenance and care
nUse a CR1632 lithium battery
lBatteries can be purchased at your Lexus dealer, local electrical appliance
shops or camera stores.
lReplace only with the same or equivalent type recommended by the manufac-
turer.
lDispose of used batteries according to the local laws.
nIf the electronic key battery is discharged
The following symptoms may occur:
lThe smart access system with push-button start and wireless remote control will
not function properly.
lThe operational range is reduced.
nWhen the card key battery needs to be replaced (if equipped)
The battery for the card key is available only at Lexus dealers. Your Lexus dealer
can replace the battery for you.
CAUTION
nRemoved battery and other parts
Keep away from children. These parts are small and if swallowed by a child, they can
cause choking. Failure to do so could result in death or serious injury.
NOTICE
nFor normal operation after replacing the battery
Observe the following precautions to prevent accidents:
lAlways work with dry hands.
Moisture may cause the battery to rust.
lDo not touch or move any other components inside the remote control.
lDo not bend either of the battery terminals.

5

When trouble arises
581
5-2. Steps to take in an emergency
If the electronic key does not operate properly
Locking and unlocking the doors and key linked functions
Use the mechanical key (→P. 2 7 )
in order to perform the following
operations (driver’s door only):
Locks all the doors
Closes the windows and moon
roof (turn and hold)
Unlocks the door
Turning the key rearward unlocks
the driver's door. Turning the key
once again unlocks the other
doors.
Opens the windows and moon
roof (turn and hold)
If communication between the electronic key and vehicle is interrupted
(→P. 36) or the electronic key cannot be used because the battery is
depleted, the smart access system with push-button start and wireless
remote control cannot be used. In such cases, the doors can be opened or
the engine can be started by following the procedure below.

625
6-2. Customization
6

Vehicle specifications
Power back
door
(→P. 5 1 )
Power back
door opening
operation using
the back door
opener button
OffOn———O
Wireless
remote con-
trol
(→P. 4 3 )
Unlocking oper-
ation
Driver's
door
unlocked
in one step,
all doors
unlocked
in two
steps
All doors
unlocked
in one step
O—OO
Automatic
light control
system
(→P. 1 8 4 )
Ti m e e l a p s e d
before the head-
lights turn off
30 sec-
onds
Off
O—OO
60 sec-
onds
90 sec-
onds
Light sensor
sensitivityStandard-2 to 2O—OO
Daytime run-
ning light systemOnOffO—OO
Automatic high
beam systemOnOff———O
ItemFunctionDefault
setting
Custom-
ized
setting

627
6-2. Customization
6

Vehicle specifications
Automatic
air condi-
tioning sys-
tem
(→P. 2 74 )
Switching
between outside
air and recircu-
lated air mode
linked to
“AUTO” switch
operation
AutoManualO——O
A/C auto switch
operationAutoManualO——O
Exhaust gas sen-
sor sensitivityStandard-3 to 3O——O
Front seats
(→P. 6 1 )
Driver’s seat
movement when
exiting the vehi-
cle (on some
models)
Full
Off
O—OOPa r t i a l
Eco Driving
Indicator
Light
(→P. 1 7 7 )
Eco Driving Indi-
cator LightOnOff—OOO
Pow e r w i n -
dows
(→P. 9 0 )
Mechanical key
linked operationOnOff———O
Wireless remote
control linked
operation
OnOff———O
ItemFunctionDefault
setting
Custom-
ized
setting

628
6-2. Customization
Moon roof
(→P. 9 3 )
Mechanical key
linked operationOnOff———O
Wireless remote
control linked
operation
OnOff———O
Intuitive
parking
assist
(→P. 220)
Buzzer volume31 to 5O——O
Detection dis-
tance of the rear
center sensor
FarNearO——O
Display setting
(when intuitive
parking assist is
operating)
All sensors
displayed
No sensor
displayedO——O
ItemFunctionDefault
setting
Custom-
ized
setting