2011 LEXUS RX350 remote control

51
1-2. Opening, closing and locking the doors
1

Before driving
nOpening the back door from outside the vehicle (vehicles with a
power back door)
Using the back door opener button*
When the back door is
unlocked: Press the back door
opener button.
When the back door is locked:
While carrying the electronic
key on your person, press and
hold the back door opener but-
ton or press it twice.
*: This setting must be customized
at your Lexus dealer.
Using the wireless remote control
→P. 4 3
nOpening the back door from inside the vehicle (vehicles with a
power back door)
Press the switch to open/close.
Pressing the switch again while
the power back door is operat-
ing will cause the operation to
reverse.

53
1-2. Opening, closing and locking the doors
1

Before driving
nThe power back door can be operated when
lThe back door is unlocked. (Except for using the back door opener button* or
wireless remote control, when the power back door can be operated even if it is
locked.)
lThe power back door main switch is on.
lTo open the power back door when the “ENGINE START STOP” switch is in
IGNITION ON mode, the power back door main switch must be on, the vehi-
cle speed must be lower than 1 mph (3 km/h) and the shift lever must be in P.
*: This setting must be customized at your Lexus dealer.
nBack door handle
nLuggage compartment lights
nBack door closer (vehicles with a power back door)
In the event that the back door is left slightly open, the back door closer will auto-
matically close it to the fully closed position.
lThe back door closer will operate regardless of the “ENGINE START STOP”
switch mode.
lThe back door can be opened while the back door closer is operating by press-
ing the back door opener button.
Use the back door handle when lowering the
back door.
Do not close the back door fully while still
holding the door handle as an injury may
result.
The luggage compartment lights turn on
when the back door is opened with the lug-
gage compartment light switch on.

71
1-3. Adjustable components (seats, mirrors, steering wheel)
1

Before driving
Linking driving position memory with door unlock operation
Record your driving position to button “1”, “2” or “3” before performing
the following:
Carry only the key (including the card key) to which you want to link the
driving position. If 2 or more keys are in the vehicle, the driving position
cannot be linked properly.
Shift the shift lever to P and close the driver's door. Turn the
“ENGINE START STOP” switch to IGNITION ON mode.
Press the desired button (“1”, “2” or
“3”) to recall the position. Then,
while keep pressing the button,
press the driver's door lock
switches (either lock or unlock)
until the signal beeps.
The driving position is recalled
when the driver's door is unlocked
using the entry function or wireless
remote control and the driver's
door is opened.
STEP1
STEP2

92
1-4. Opening and closing the windows and moon roof
nDoor lock linked window operation
lThe power windows can be opened and closed using the mechanical key.
(→P. 581)
lThe power windows can be opened using the wireless remote control. (→P. 4 3 )
nWhen the battery is disconnected
The window lock switch is disabled. If necessary, press the window lock switch after
reconnecting the battery.
nCustomization
Settings (e.g. linked door lock operation) can be changed.
(Customizable features →P. 6 2 1 )
CAUTION
nClosing the windows
Observe the following precautions.
Failing to do so may result in death or serious injury.
lCheck to make sure that all passengers do not have any part of their body in a
position where it could be caught when a window is being operated.
lDo not allow children to operate the power windows.
Closing a power window on someone can cause serious injury, and in some
instances, even death.
nJam protection function
lNever use any part of your body to intentionally activate the jam protection func-
tion.
lThe jam protection function may not work if something gets caught just before
the window fully closes. Also, the jam protection does not operate when the
power window switch is pulled up continually to close the windows.

94
1-4. Opening and closing the windows and moon roof
nThe moon roof can be operated when
The “ENGINE START STOP” switch is in IGNITION ON mode.
nOperating the moon roof after turning the engine off
The moon roof can be operated for approximately 45 seconds even after the
“ENGINE START STOP” switch is turned to ACCESSORY mode or turned off. It
cannot, however, be operated once either front door is opened.
nJam protection function
If an object is detected between the moon roof and the frame while closing or tilting
down, travel is stopped and the moon roof opens slightly.
nSunshade
The sunshade can be opened and closed manually. However, the sunshade will
open automatically when the moon roof is opened.
nDoor lock linked moon roof operation
lThe moon roof can be opened and closed using the mechanical key. (→P. 5 8 1 )
lThe moon roof can be opened using the wireless remote control. (→P. 4 3 )

103
1
1-6. Theft deterrent system

Before driving
Alarm
The system sounds the alarm and flashes the lights when forcible entry is
detected.
nTriggering of the alarm
The alarm is triggered in the following situations when the alarm is
set:
lA locked door is unlocked or opened in any way other than using
the entry function, wireless remote control or mechanical key.
lThe hood is opened.
lSome models: The back door window is tapped or broken.
nSetting the alarm system
Close the doors and hood, and
lock all the doors.
The system will be set automati-
cally after 30 seconds.
The indicator light changes from
being on to flashing when the
system is set.
nDeactivating or stopping the alarm
Do one of the following to deactivate or stop the alarms:
lUnlock the doors.
lTurn the “ENGINE START STOP” switch to ACCESSORY or
IGNITION ON mode, or start the engine. (The alarm will be
deactivated or stopped after a few seconds.)

426
3-7. Other interior features
Garage door opener
The garage door opener (HomeLink® Universal Transceiver) is manufactured
under license from HomeLink®.
Programming the HomeLink® (for U.S.A. owners)
The HomeLink® compatible transceiver in your vehicle has 3 buttons
which can be programmed to operate 3 different devices. Refer to the
programming method below appropriate for the device.
Indicator
Buttons
nProgramming the HomeLink®
Point the remote control transmit-
ter for the device 1 to 3 in. (25 to
75 mm) from the HomeLink®
control buttons.
Keep the HomeLink® indicator
light in view while programming.
The garage door opener can be programmed to operate garage doors,
gates, entry doors, door locks, home lighting systems, security systems, and
other devices.
STEP1

427
3-7. Other interior features
3

Interior features
Press and hold one of the
HomeLink® buttons and the trans-
mitter button. When the
HomeLink® indicator light
changes from a slow to a rapid
flash, you can release both buttons.
If the HomeLink® indicator light
comes on but does not flash, or
flashes rapidly for 2 seconds and
remains lit, the HomeLink® button
is already programmed. Use the
other buttons or follow the “Repro-
gramming a HomeLink® button”
instructions. (→P. 4 2 9 )
Test the HomeLink® operation by
pressing the newly programmed
button.
If a HomeLink® button has been
programmed for a garage door,
check to see if the garage door
opens and closes. If the garage
door does not operate, see if your
remote control transmitter is of the
rolling code type. Press and hold
the programmed HomeLink® but-
ton. The remote control transmitter
is of the rolling code type if the
HomeLink® indicator light flashes
rapidly for 2 seconds and then
remains lit. If your transmitter is of
the rolling code type, proceed to
the heading “Programming a roll-
ing code system”.
Repeat the steps above to program another device for each of
the remaining HomeLink® buttons.
STEP2
STEP3
STEP4