2011 Lexus IS220d ECO mode

156
2-1. Driving procedures
IS250/220d/200d_EE
Engine (ignition) switch
Performing the following operations when carrying the electronic key
on your person starts the engine or changes “ENGINE START STOP”
switch modes.
Starting the engine
Automatic transmission
Check that the parking brake is set.
Check that the shift lever is set in P.
Sit in the driver’s seat and firmly depress the brake pedal.
The “ENGINE START STOP” switch indicator turns green.
Press the “ENGINE START
STOP” switch.
The engine will crank until it
starts or for up to 30 seconds,
whichever is less.
Continue depressing the
brake pedal until the engine
is completely started.
The engine can be started
from any “ENGINE START
STOP” switch mode.
STEP1
STEP2
STEP3
STEP4

157
2-1. Driving procedures
2
When driving
IS250/220d/200d_EE
Manual transmission
Check that the parking brake is set.
Check that the shift lever is set in N.
Firmly depress the clutch pedal.
The “ENGINE START STOP” switch indicator turns green.
Press the “ENGINE START
STOP” switch.
indicator turns on. The
engine begins starting after
the indicator light goes out.
The engine will crank until it
starts or for up to 30 seconds,
whichever is less.
Continue depressing the
clutch pedal until the engine
is completely started.
The engine can be started
from any “ENGINE START
STOP” switch mode.
STEP1
STEP2
STEP3
STEP4

160
2-1. Driving procedures
IS250/220d/200d_EE
CAUTION
When starting the engine
Always start the engine while sitting in the driver's seat. Do not press the
accelerator while starting the engine under any circumstances.
Doing so may cause an accident resulting in death or serious injury.
Stopping the engine in an emergency
If you want to stop the engine in an emergency while driving the vehicle,
push and hold the “ENGINE START STOP” switch for more than 3 sec-
onds.
However, do not touch the “ENGINE START STOP” switch while driving
except in an emergency. Turning the engine off while driving will not cause
loss of steering or braking control, but the power assist to these systems will
be lost. This will make it more difficult to steer and brake, so you should
pull over and stop the vehicle as soon as it is safe to do so.
NOTICE
To prevent battery discharge
Do not leave the “ENGINE START STOP” switch in ACCESSORY or
IGNITION ON mode for long periods without the engine running.
When starting the engine
Do not race a cold engine.
If the engine becomes difficult to start or stalls frequently, have the engine
checked immediately.

174
2-2. Instrument cluster
IS250/220d/200d_EEChanging the indicator setting
The satellite switch can be used to change the set speed at which
the yellow speed or tacho indicator ring comes on.
The setting can be made only when the “ENGINE START
STOP” switch is in IGNITION ON mode and the vehicle is
stopped.
Push “
” or “” to select the speed or tacho indicator set mode.
( ) Turn the speed or tacho indicator to “OFF” and then “ON” by
pushing the “ON/OFF” button. ( )
After one second, the mode
enters the indicator setting
mode.
The speedometer or tachometer
needle moves to the previously
set speed.
STEP1

175
2-2. Instrument cluster
2
When driving
IS250/220d/200d_EEPush “
” or “” within 6 seconds of the speedometer or tachome-
ter needle moving to change the setting of the desired speed, then
turn the indicator mode to “ON” by pushing the “ON/OFF” button.
Pushing and holding the switch changes values at a faster rate.
If the satellite switch is not operated for some time, the multi-informa-
tion display returns to its previously displayed content.
The yellow indicator is displayed to indicate that the desired speed
has been set.
STEP2

179
2-2. Instrument cluster
2
When driving
IS250/220d/200d_EE
*1:These lights turn on when the “ENGINE START STOP” switch is
turned to IGNITION ON mode to indicate that a system check is
being performed. They will turn off after the engine is started, or
after a few seconds. There may be a malfunction in a system if a
light does not come on, or if the lights do not turn off. Have the
vehicle inspected by any authorized Lexus dealer or repairer, or
another duly qualified and equipped professional, for details.
*2:The light flashes to indicate that the system is operating
(if
equipped)
Daytime running light
system off indicator
(P. 188)SRS airbag on-off indi-
cator (P. 140)
(vehicles
with a man-
ual trans-
mission)Engine preheating indi-
cator (P. 156)
*1

180
2-2. Instrument cluster
IS250/220d/200d_EE
CAUTION
If a safety system warning light does not come on
Should a safety system light such as the ABS and SRS warning light not
come on when you start the engine, this could mean that these systems are
not available to help protect you in an accident, which could result in death
or serious injury. Have the vehicle inspected by any authorized Lexus dealer
or repairer, or another duly qualified and equipped professional, immedi-
ately if this occurs.
Warning lights
Warning lights inform the driver of malfunctions in any of the
vehicle’s systems. (P. 467)
*:These lights turn on when the “ENGINE START STOP” switch is
turned to IGNITION ON mode to indicate that a system check is
being performed. They will turn off after the engine is started, or
after a few seconds. There may be a malfunction in a system if a
light does not come on, or if the lights do not turn off. Have the
vehicle inspected by any authorized Lexus dealer or repairer, or
(vehicles
with a
manual
transmis-
sion)
(if equipped)(for
driver)(for front
passen-
ger)
*****
*****

196
2-3. Operating the lights and windshield wipers
IS250/220d/200d_EE
If no windshield washer fluid sprays
If there is washer fluid in the windshield washer fluid reservoir and no
washer fluid sprays, the nozzle may be blocked. In this case, contact any
authorized Lexus dealer or repairer, or another duly qualified and equipped
professional, and have your Lexus inspected.
Customization that can be configured at any authorized Lexus dealer or
repairer, or another duly qualified and equipped professional
Settings (e.g. drip prevention function) can be changed.
(Customizable features P. 556)
CAUTION
Caution regarding the use of windshield wipers in “AUTO” mode (vehicles
with rain-sensing windshield wipers)
The windshield wipers may operate unexpectedly if the sensor is touched or
the windshield is subject to vibration in “AUTO” mode. Take care that your
fingers or anything else do not become caught in the windshield wipers.
Caution regarding the use of washer fluid
When it is cold, do not use the washer fluid until the windshield becomes
warm. The fluid may freeze on the windscreen and cause low visibility. This
may lead to an accident, resulting in death or serious injury.
NOTICE
When the windshield is dry
Do not use the wipers, as they may damage the windshield.
When a nozzle becomes blocked
Do not try to clear it with a pin or other object. The nozzle will be damaged.
When there is no washer fluid spray from the nozzle
Damage to the washer fluid pump may be caused if the lever is pulled
toward you and held continually.