2011 Lexus ES350 differential

SCHEDULED MAINTENANCE LOG
MAINTENANCE
Scheduled MaintenanceLog65
162 Months or 135,000 Miles
Replace engine oil and oil filter; reset reminder light
Rotate tires1
Clean air conditioner filter (ES, GS)
Visually inspect brake pads, calipers and rotors
Check installation of driver’s floor mat
Roadtest vehicle
Inspect the following:
___Axle shaft boots
___Ball joints and dust covers
___Body
___Brake lines and hoses
___Drive belt
___Exhaust pipes and mountings
Additional Maintenance Required If You Drive Primarily Under the Following Conditions
Driving on dirtroads or dusty roads:
Inspect engine air filter
Tighten nuts and bolts on chassis
Driving while towing:
Tighten nuts and bolts on chassis (ES)
___Front differential oil (GS 350 AWD,
LS 460 AWD)
___Rack and pinion assembly
___Rear differential oil (GS, LS)
___Steering linkage and boots
Date: _____________________________ Mileage: ____________________________
Notes:

SCHEDULED MAINTENANCE LOG
MAINTENANCE
Scheduled MaintenanceLog67
180 Months or 150,000 Miles
Replace engine oil and oil filter; reset reminder light
Rotate tires1
Measure thickness of brake pads and runout of
brake rotors
Replace air conditioner filter
Replace brake fluid
Replace engine air filter
Inspect the following:
___Axle shaft boots
___Ball joints and dust covers
___Body
___Brake lines and hoses
___Drive belt
___Exhaust pipes and mountings
___Front differential oil (GS 350 AWD, LS 460 AWD)
___Fuel lines and connections, fuel tank band
and fuel tank vapor vent system hoses
Additional Maintenance Required If You Drive Primarily Under the Following Conditions
Driving on dirt roads or dusty roads:
Tighten nuts and bolts on chassis
Driving while towing:
Tighten nuts and bolts on chassis (ES)
___Fuel tank cap gasket
___Rack and pinion assembly
___Rear differential oil (GS, LS)
___Steering linkage and boots
___Transfer case for signs of leakage
(GS350 AWD, LS 460 AWD)
___Transmission for signs of leakage
Date: _____________________________ Mileage: ____________________________
Notes:
Replace engine coolant (see page 69)
Replace Smart Key battery
Visually inspect brake pads, calipers
and rotors
Check installation of driver’s floor mat
Roadtest vehicle

EXPLANATION OF MAINTENANCE ITEMS
MAINTENANCE
Scheduled MaintenanceLog69
Brake Pads, Calipers and Rotors
Check brake pads and rotors for
excessive wear; check brake rotors
for runout. Check brake calipers for
fluid leakage. Some models are
equipped with directional rotors.
When servicing these rotors, reinstall
at same location. A qualified techni
cian should perform these operations.
See inside front cover for additional
brake information.
Differential Oil
Inspect each differential component
for signs of leakage. If you discover
any leakage, have it repaired immedi
ately bya qualified technician. Refer
to your
Owner’sManualfor fluid
specifications.
Drive Belt
Inspect for cracks, excessive wear
and oiliness. Check the belt tension
and adjust if necessary. Replace the
belt if it is damaged.
Driver’s Floor Mat
•
Only use the driver’s floor mat
designed specifically for the
model and model year of your
vehicle, such as Lexus Genuine
floor mats.
•Always properly secure the dri
ver’s floor mat using the retaining
hooks.
•Never install another floor mat
on top of the existing driver’s
floor mat.
•Never install the driver’s floor
mat upside down.
Engine Air Filter
Check for excessive dirt, damage and
oiliness. Replace if necessary.
Engine Coolant
When inspecting, visually check
the engine coolant level on the see
through reservoir. Add coolant as
necessary. When replacing, drain
and flush the cooling system and refill
with coolant. Always use Genuine
Toyota Super LongLife Coolant or
similar highquality nonsilicate, non
amine, nonnitrate, nonborate ethyl
eneglycol coolant with longlife
hybrid organic acid technology (i.e., a combination of low phosphates and
organic acids). Check that the radia
tor is not blocked with leaves, dirt or
insects and clean if necessary. Also
check the hose connections for cor
rosion and condition of installation. A qualified technician should perform
these operations.