2011 Lexus CT200h ECO mode

121
1-5. Opening and closing the windows and moon roof
1
Before driving
CT200h_EE (OM76041E)
When the power window does not close normally
If the jam protection function is operating abnormally and a window cannot
be closed, perform the following operations using the power window switch
on the relevant door.
After stopping the vehicle, the window can be closed by holding the
power window switch in the one-touch closing position while the
“POWER” switch is turned to ON mode.
If the window still cannot be closed even by carrying out the operation
explained above, initialize the function by performing the following pro-
cedure.
Hold the power window switch in the one-touch closing position.
Continue holding the switch for a further 6 seconds after the win-
dow has closed.
Hold the power window switch in the one-touch opening position.
Continue holding the switch for a further 2 seconds after the win-
dow has opened completely.
Hold the power window switch in the one-touch closing position
once again. Continue holding the switch for a further 2 seconds
after the window has closed.
If you release the switch while the window is moving, start again from the
beginning.
If the window continues to close but then re-open slightly even after per-
forming the above procedure correctly, have the vehicle inspected by any
authorized Lexus dealer or repairer, or another duly qualified and equipped
professional.
STEP1
STEP2
STEP3

124
1-5. Opening and closing the windows and moon roof
CT200h_EE (OM76041E)
The moon roof can be operated when
The “POWER” switch is in ON mode.
Operating the moon roof after turning the hybrid system off
The moon roof can be operated for approximately 43 seconds even after the
“POWER” switch is turned to ACCESSORY mode or turned off. It cannot,
however, be operated once either front door is opened.
Jam protection function
If an object is detected between the moon roof and the frame while the
moon roof is closing or tilting down, travel is stopped and the moon roof
opens slightly.
Sunshade
The sunshade can be opened and closed manually. However, the sunshade
will open automatically to slightly before the fully open position when the
moon roof is opened.

197
2-1. Driving procedures
2
When driving
CT200h_EE (OM76041E)
Stopping the hybrid system
Stop the vehicle completely.
Set the parking brake. (P. 214)
Shift the shift position to P. (P. 2 0 7 )
Check that the shift position indicator shows P. (P. 204)
Press the “POWER” switch.
The hybrid system will stop, and the meter display will be
extinguished (the shift position indicator will be extinguished
a few seconds after the meter display).
Slowly release the brake pedal and check that the indica-
tor on the “POWER” switch is off.
Changing “POWER” switch modes
Modes can be changed by pressing the “POWER” switch with
the brake pedal released. (The mode changes each time the
switch is pressed.)
Off
The emergency flashers can
be used.
ACCESSORY mode
Some electrical components
such as the audio system can
be used.
The “POWER” switch indi-
cator turns amber.
ON mode
All electrical components can
be used.
The “POWER” switch indi-
cator turns amber.
STEP1
STEP2
STEP3
STEP4
STEP5

199
2-1. Driving procedures
2
When driving
CT200h_EE (OM76041E)
If the “READY” indicator does not come on
If the “READY” indicator does not come on when you press the “POWER”
switch with the shift position in P and the brake pedal depressed, contact
any authorized Lexus dealer or repairer, or another duly qualified and
equipped professional immediately.
If the hybrid system is malfunctioning
P. 5 6 0
If the electronic key battery is depleted
P. 5 1 5
Operation of the “POWER” switch
When operating the “POWER” switch, one short, firm press is enough.
If the switch is pressed improperly, the hybrid system may not start or
the “POWER” switch mode may not change. It is not necessary to press
and hold the switch.
If attempting to restart the hybrid system immediately after turning the
“POWER” switch off, the hybrid system may not start in some cases.
After turning the “POWER” switch off, please wait a few seconds before
restarting the hybrid system.
Automatically P position selection function
P. 2 1 0
When the P position control system malfunctions
The “POWER” switch will not be able to be turned off. In such a case, the
switch can be turned off after applying the parking brake.
Have the vehicle inspected by any authorized Lexus dealer or repairer, or
another duly qualified and equipped professional immediately.

200
2-1. Driving procedures
CT200h_EE (OM76041E)
CAUTION
When starting the hybrid system
Always start the hybrid system while sitting in the driver’s seat. Do not
depress the accelerator pedal while starting the hybrid system under any cir-
cumstances.
Doing so may cause an accident resulting in death or serious injury.
Stopping the hybrid system in an emergency
If you want to stop the hybrid system in an emergency while driving the
vehicle, press and hold the “POWER” switch for more than 3 seconds, or
press it briefly 3 times or more in succession.
However, do not touch the “POWER” switch while driving except in an
emergency. Turning the hybrid system off while driving will not cause loss
of steering or braking control, but the power assist to these systems will be
lost. This will make it more difficult to steer and brake, so you should pull
over and stop the vehicle as soon as it is safe to do so.
NOTICE
To prevent 12-volt battery discharge
Do not leave the “POWER” switch in ACCESSORY or ON mode for long
periods of time without the hybrid system on.
If the hybrid system is off, but the indicator on the “POWER” switch is
illuminated, this indicates that the “POWER” switch is still turned on.
When exiting the vehicle, always check that the “POWER” switch is off.
Symptoms indicating a malfunction with the “POWER” switch
If the “POWER” switch seems to be operating somewhat differently than
usual, such as the switch sticking slightly, there may be a malfunction. Con-
tact any authorized Lexus dealer or repairer, or another duly qualified and
equipped professional immediately.

202
2-1. Driving procedures
CT200h_EE (OM76041E)
Situations in which EV drive mode cannot be turned on
It may not be possible to turn EV drive mode on in the following situations.
If it cannot be turned on, a buzzer will sound and a message will be shown
on the multi-information display.
The temperature of the hybrid system is high.
The vehicle has been left in the sun, driven on a hill, driven at high
speeds, etc.
The temperature of the hybrid system is low.
The vehicle has been left in temperatures lower than about 0 C (32 F)
for a long period of time etc.
The gasoline engine is warming up.
The hybrid battery (traction battery) is low.
An “Energy monitor” display of level 3 or lower may indicate a low bat-
tery level. (P. 4 5 )
Vehicle speed is high.
The accelerator pedal is depressed firmly or the vehicle is on a hill etc.
The windshield defogger is in use.
Switching to EV drive mode when the gasoline engine is cold
If the hybrid system is started while the gasoline engine is cold, the gasoline
engine will start automatically after a short period of time in order to warm
up. In this case, you will become unable to switch to EV drive mode.
After the hybrid system has started and the “READY” indicator has illumi-
nated, press the EV drive mode switch before the gasoline engine starts to
switch to EV drive mode.

203
2-1. Driving procedures
2
When driving
CT200h_EE (OM76041E)
Automatic cancellation of EV drive mode
When driving in EV drive mode, the gasoline engine may automatically
restart in the following situations. When EV drive mode is canceled, a
buzzer will sound and the EV drive mode indicator will flash and go off.
The hybrid battery (traction battery) becomes low.
The remaining battery level indicated in the “Energy monitor” display is
level 2 or lower. (P. 4 5 )
Vehicle speed becomes high.
The accelerator pedal is depressed firmly or the vehicle is on a hill etc.
When it is possible to inform the driver of automatic cancelation in advance,
a prior notice screen will appear on the multi-information display.
 Possible driving distance when driving in EV drive mode
In EV drive mode, it is possible to drive up to about 1 km (1/2 mile) if driv-
ing at a speed of about 45 km/h (28 mph) or less. (The distance that is possi-
ble depends on the hybrid battery [traction battery] level and driving
conditions.)
Fuel economy
CT200h is designed to achieve the best possible fuel economy during nor-
mal driving (using the gasoline engine and electric motor [traction motor]).
Driving in EV drive mode more than necessary may lower fuel economy.
CAUTION
While driving
When driving in EV drive mode, pay special attention to the area around the
vehicle. Because there is no engine noise, pedestrians, people riding bicy-
cles or other people and vehicles in the area may not be aware of the vehicle
starting off or approaching them, so take extra care while driving.

206
2-1. Driving procedures
CT200h_EE (OM76041E)
Selecting a driving mode
The following modes can be selected to suit driving condi-
tions:
Normal mode
Eco drive mode
The torque generated in
response to accelerator pedal
depression will lessen com-
pared to normal, and air con-
ditioning operation (heating/
cooling) will be restrained,
thus suiting driving with
improved fuel efficiency.
When the driving mode
select switch is turned left,
the “ECO MODE” indicator
comes on in the instrument
cluster.
Press the switch to change
the driving mode to normal
mode.
Sport mode
Use when high levels of
response and feeling are
desirable, such as when driv-
ing in mountainous regions
or when overtaking.
When the driving mode
select switch is turned right,
the “SPORT MODE” indica-
tor comes on in the instru-
ment cluster