2011 JEEP GRAND CHEROKEE stop start

NOTE:
You can insert the double-sided emergency
key into the lock cylinders with either side
up.
Removing Key Fob From IgnitionPlace the shift lever in PARK. Turn the Key Fob
to the OFF position and then remove the Key
Fob.
With the Keyless Enter-N-Go feature, the EVIC
will display the ignition switch position “OFF/
ACC/RUN”. Refer to “Electronic Vehicle Infor-
mation Center (EVIC)” in “Understanding Your
Instrument Panel” for further information.NOTE:
•
If you try to remove the Key Fob before
you place the shift lever in PARK, it may
become trapped temporarily in the igni-
tion switch. If this occurs, rotate the key
to the right slightly, then remove the Key
Fob as described. If a malfunction occurs,
the system may trap the key in the igni-
tion switch to warn you that this safety
feature is inoperable. The engine can be
started and stopped, but the Key Fob
cannot be removed until you obtain ser-
vice.
• The power window switches, radio, power
sunroof (if equipped), and power outlets
will remain active for up to 10 minutes
after the ignition switch is turned to the
LOCK position. Opening either front door
will cancel this feature. The time for this
feature is programmable. Refer to “Elec-
tronic Vehicle Information Center (EVIC)/
Personal Settings (Customer-Program-
mable Features)” in “Understanding Your
Instrument Panel” for further information.
WARNING!
• Never leave children alone in a vehicle.
Leaving unattended children in a vehicle is
dangerous for a number of reasons. A child
or others could be seriously or fatally in-
jured. Do not leave the Key Fob in the
ignition or Keyless Enter-N-Go in the ACC
or ON/RUN mode. A child could operate
power windows, other controls, or move the
vehicle.
• Do not leave children or animals inside
parked vehicles in hot weather. Interior
heat build-up may cause serious injury or
death.
CAUTION!
An unlocked car is an invitation to thieves.
Always remove Key Fob from the ignition and
lock all doors when leaving the vehicle unat-
tended.
Emergency Key Removal
13

Key-In-Ignition ReminderOpening the driver’s door when the Key Fob is
in the ignition and the ignition switch position is
OFF or ACC, sounds a signal to remind you to
remove the Key Fob.
NOTE:
The Key-In-Ignition reminder only sounds
when the Key Fob is placed in the OFF or
ACC ignition position.
With the Keyless Enter-N-Go feature, opening
the driver’s door when the vehicle’s ignition
switch is placed in ACC or ON/RUN (engine
stopped) will cause the reminder chime to
sound. Refer to “Starting Procedures” in “Start-
ing And Operating” for further information.
SENTRY KEYThe Sentry Key Immobilizer system prevents
unauthorized vehicle operation by disabling
the engine. The system does not need to be
armed or activated. Operation is automatic,
regardless of whether the vehicle is locked or
unlocked. The system uses the factory-mated Key Fob
with Remote Keyless Entry (RKE) transmitter
and Wireless Ignition Node (WIN) to prevent
unauthorized vehicle operation. Therefore, only
Key Fobs that are programmed to the vehicle
can be used to start and operate the vehicle.
The system will shut the engine off in two
seconds if an invalid Key Fob is used to start
the engine.
After turning the ignition switch to the ON/RUN
position, the Vehicle Security Light will turn on
for three seconds for a bulb check. If the light
remains on after the bulb check, it indicates
that there is a problem with the electronics. In
addition, if the light begins to flash after the
bulb check, it indicates that someone used an
invalid Key Fob to start the engine. Either of
these conditions will result in the engine being
shut off after two seconds.
If the Vehicle Security Light turns on during
normal vehicle operation (vehicle running for
longer than 10 seconds), it indicates that there
is a fault in the electronics. Should this occur,
have the vehicle serviced as soon as possible
by an authorized dealer.
CAUTION!
The Sentry Key
Immobilizer system is not
compatible with some after-market remote
starting systems. Use of these systems may
result in vehicle starting problems and loss of
security protection.
All of the Key Fobs provided with your new
vehicle have been programmed to the vehicle
electronics.
Replacement Keys
NOTE:
Only Key Fobs that are programmed to the
vehicle electronics can be used to start and
operate the vehicle. Once a Key Fob is
programmed to a vehicle, it cannot be pro-
grammed to any other vehicle.
CAUTION!
• Always remove the Key Fobs from the
vehicle and lock all doors when leaving the
vehicle unattended.
(Continued)
14

CAUTION!(Continued)
• With Keyless Enter-N-Go, always remem-
ber to place the ignition in OFF.
At the time of purchase, the original owner is
provided with a four-digit Personal Identifica-
tion Number (PIN). Keep the PIN in a secure
location. This number is required for authorized
dealer replacement of Key Fobs. Duplication of
Key Fobs may be performed at an authorized
dealer.
NOTE:
When having the Sentry Key Immobilizer
system serviced, bring all vehicle ignition
keys with you to an authorized dealer.
Customer Key ProgrammingProgramming Key Fobs or RKE transmitters
may be performed at an authorized dealer.
General InformationThe Sentry Key operates on a carrier fre-
quency of 433.92 MHz. The Sentry Key Immo-
bilizer system will be used in the following
European countries, which apply Directive
1999/5/EC: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Ireland, Italy, Luxembourg, Nether-
lands, Norway, Poland, Portugal, Romania,
Russian Federation, Slovenia, Spain, Sweden,
Switzerland, Yugoslavia, and United Kingdom.
Operation is subject to the following conditions:
•
This device may not cause harmful interfer-
ence.
• This device must accept any interference
that may be received, including interference
that may cause undesired operation.
VEHICLE SECURITY ALARM —
IF EQUIPPED
The Vehicle Security Alarm monitors the hood,
liftgate, liftgate flipper glass, vehicle doors for
unauthorized entry, and the ignition switch for
unauthorized operation. If something triggers
the alarm, the Vehicle Security Alarm will pre-
vent the vehicle from starting and provide the
following audio and visual signals: the horn will
pulse, the headlights will flash, the park lights
will flash, and the Vehicle Security Light in the
instrument cluster will flash.
To Arm the System
Vehicles Not Equipped with Keyless
Enter-N-Go
Remove the key from the ignition switch and
either press a power door lock switch while the
driver or passenger door is open, or press the
LOCK button on the Remote Keyless Entry
(RKE) transmitter. After the last door is closed,
or if all doors are closed, the Vehicle Security
Alarm will arm itself in about 16 seconds.
During that time, the Vehicle Security Light will
flash. If it does not illuminate, the Vehicle Secu-
rity Alarm is not arming. Also, if you open a door
during the arming period, the Vehicle Security
Alarm will cancel the arming process. If you
wish to rearm the Vehicle Security Alarm after
closing the door, you must repeat one of the
previously-described arming sequences.
Vehicles Equipped with Keyless
Enter-N-Go
Press the Keyless Enter-N-Go Start/Stop button
until the Electronic Vehicle Information Center
(EVIC) indicates that the vehicle ignition is
“OFF” (refer to “Starting Procedures” in “Start-
ing And Operating” for further information).
Then either press the power door LOCK switch
15

while the driver or passenger door is open,
press the lock button on the front driver or
passenger door handle with a valid key fob in
range, or press the Remote Keyless Entry
(RKE) transmitter LOCK button (refer to “Pas-
sive Entry System” in “Things To Know Before
Starting Your Vehicle” for further information).
To Disarm the System
Vehicles Not Equipped with Keyless
Enter-N-Go
Either press the UNLOCK button on the RKE
transmitter, or insert a valid ignition key into the
ignition switch, and turn the key to the ON/RUN
position.
NOTE:
•The driver’s door key cylinder cannot arm
or disarm the Vehicle Security Alarm.
• When the Vehicle Security Alarm is
armed, the interior power door lock
switches will not unlock the doors. Vehicles Equipped with Keyless
Enter-N-Go
Either press the UNLOCK button on the RKE
transmitter, pull on the front driver or passenger
door handle (refer to “Passive Entry System” in
“Things To Know Before Starting Your Vehicle”
for further information) with a valid key fob in
range, or press the Keyless Enter-N-Go Start/
Stop button (requires at least one valid Key Fob
in the vehicle), or insert a valid Key Fob into the
ignition switch (if the Start/Stop button is re-
moved) and rotate it to the ON/RUN position.
The Vehicle Security Alarm is designed to pro-
tect your vehicle; however, you can create
conditions where the Vehicle Security Alarm will
give you a false alarm. If one of the previously-
described arming sequences has occurred,
the Vehicle Security Alarm will arm, regardless
of whether you are in the vehicle or not. If you
remain in the vehicle and open a door, the
alarm will sound. If this occurs, disarm the
Vehicle Security Alarm.
If the Vehicle Security Alarm is armed, and the
battery becomes disconnected, the Vehicle Security Alarm will remain armed when the
battery is reconnected. The exterior lights will
flash, the horn will sound, and the ignition will
not start the vehicle. If this occurs, disarm the
Vehicle Security Alarm.
ILLUMINATED ENTRYThe interior lights come on when you open any
door or use the Remote Keyless Entry (RKE)
transmitter to unlock any door. They will remain
on for approximately 30 seconds after all doors
are closed then fade to off.
The lights also will fade to off if you turn on the
ignition after you close all the doors. Refer to
“Electronic Vehicle Information Center (EVIC)/
Personal Settings (Customer-Programmable
Features)” in “Understanding Your Instrument
Panel” for further information.
NOTE:
None of the courtesy lights will operate if the
dimmer control is in the “defeat” position
(extreme downward position), unless the
overhead map/reading lights are turned on
manually.
16

•Uconnect™ Phone will play the new text
message for you.
After reading a message, you can “Reply” or
“Forward” the message using Uconnect™
Phone.
Send Messages:
You can send messages using Uconnect™
Phone. To send a new message:
• Press the
button.
• After the “Ready” prompt and the following
beep, say “SMS Send” or “Send Messages”.
• You can either say the message you wish to
send or say “List Messages.” There are 20
preset messages.
To send a message, press the
button
while the system is listing the message and say
“Send.”
Uconnect™ Phone will prompt you to say the
name or number of the person you wish to send
the message to.
List of Preset Messages:
1. Yes 2. No
3. Where are you?
4. I need more direction.
5. LOL
6. Why
7. I love you
8. Call me
9. Call me later
10. Thanks
11. See You in 15 minutes
12. Iamonmyway
13. I’ll be late
14. Are you there yet?
15. Where are we meeting?
16. Can this wait?
17. Bye for now
18. When can we meet
19. Send number to call
20. Start without meTurn SMS Incoming Announcement
ON/OFF
Turning the SMS Incoming Announcement OFF
will stop the system from announcing the new
incoming messages.
•
Press the
button.
• After the “Ready” prompt and the following
beep, say “Setup, Incoming Message An-
nouncement”, you will then be given a
choice to change it.
Bluetooth Communication Link
Mobile phones have been found to lose con-
nection to the Uconnect™ Phone. When this
happens, the connection can generally be re-
established by switching the phone off/on. Your
mobile phone is recommended to remain in
Bluetooth ON mode.
Power-Up
After switching the ignition key from OFF to
either ON or ACC position, or after a language
change, you must wait at least 15 seconds
prior to using the system.
87

Changing the Volume
1. Start a dialogue by pressing the Voice
Command
button.
2. Say a command (e.g., “Help”).
3. Use the ON/OFF VOLUME rotary knob to
adjust the volume to a comfortable level while
the Voice Command system is speaking.
Please note the volume setting for Voice Com-
mand is different than the audio system.
Main Menu
Start a dialogue by pressing the Voice
Command
button. You may say “Main
Menu” to switch to the main menu.
In this mode, you can say the following com-
mands:
• “Radio” (to switch to the radio mode)
• “Disc” (to switch to the disc mode)
• “Memo” (to switch to the memo recorder)
• “System Setup” (to switch to system setup) Radio AM (or Radio Long Wave or Radio
Medium Wave — If Equipped)
To switch to the AM band, say “AM” or “Radio
AM”. In this mode, you may say the following
commands:
•
“Frequency” (to change the frequency)
• “Next Station” (to select the next station)
• “Previous Station” (to select the previous
station)
• “Radio Menu” (to switch to the radio menu)
• “Main Menu” (to switch to the main menu)
Radio FM
To switch to the FM band, say “FM” or “Radio
FM”. In this mode, you may say the following
commands:
• “Frequency” (to change the frequency)
• “Next Station” (to select the next station)
• “Previous Station” (to select the previous
station)
• “Radio Menu” (to switch to the radio menu)
• “Main Menu” (to switch to the main menu) Disc
To switch to the disc mode, say “Disc”. In this
mode, you may say the following commands:
•
“Track” (#) (to change the track)
• “Next Track” (to play the next track)
• “Previous Track” (to play the previous track)
• “Main Menu” (to switch to the main menu)
Memo
To switch to the voice recorder mode, say
“Memo”. In this mode, you may say the follow-
ing commands:
• “New Memo” (to record a new memo) —
During the recording, you may press the
Voice Command
button to stop re-
cording. You proceed by saying one of the
following commands:
“Save” (to save the memo)
“Continue” (to continue recording)
“Delete” (to delete the recording)
• “Play Memos” (to play previously recorded
memos) — During the playback you may
press the Voice Command
button to
93

WARNING!(Continued)
•Active Head Restraints may be deployed if
they are struck by an object such as a hand,
foot or loose cargo. To avoid accidental
deployment of the Active Head Restraint
ensure that all cargo is secured, as loose
cargo could contact the Active Head Re-
straint during sudden stops. Failure to fol-
low this warning could cause personal injury
if the Active Head Restraint is deployed.
Head Restraints — Rear Seats
The head restraints on the outboard seats are
not adjustable. They automatically fold forward
when the rear seat is folded to a load floor
position but do not return to their normal posi-
tion when the rear seat is raised. After returning
either seat to its upright position, raise the head
restraint until it locks in place. The outboard
headrests are not removable.
The center head restraint has limited adjust-
ment. Lift upward on the head restraint to raise
it, or push downward on the head restraint to
lower it.WARNING!
Sitting in a seat with the head restraint in its
lowered position could result in serious injury
or death in a collision. Always make sure the
outboard head restraints are in their upright
positions when the seat is to be occupied.
NOTE:
For proper routing of a Child Seat Tether
refer to “Occupant Restraints” in “Things to
Know Before Starting Your Vehicle” for fur-
ther information.
60/40 Split Rear Seat
To Lower Rear Seat
Either side of the rear seat can be lowered to
allow for extended cargo space and still main-
tain some rear seating room.
NOTE:
Be sure that the front seats are fully upright
and positioned forward. This will allow the
rear seatback to fold down easily.
1. Pull upward on the release lever to release
the seat.
Rear Head Restraint
Rear Seat Release
101

12. Repeat the above steps to set the next
memory position, using the other numbered
memory button, or to link another RKE transmit-
ter to memory.
Memory Position Recall
NOTE:
The vehicle must be in PARK to recall
memory positions. If a recall is attempted
when the vehicle is not in PARK, a message
will be displayed in the Electronic Vehicle
Information Center (EVIC).
To recall the memory settings for driver one,
press MEMORY button number 1 on the driv-
er’s door, or the UNLOCK button on the RKE
transmitter linked to memory position 1.
To recall the memory setting for driver two,
press MEMORY button number 2 on the driv-
er’s door, or the UNLOCK button on the RKE
transmitter linked to memory position 2.
A recall can be cancelled by pressing any of
the MEMORY buttons on the drivers door dur-
ing a recall (S, 1, or 2). When a recall is
cancelled, the driver’s seat, driver’s mirror andthe pedals stop moving. A delay of one second
will occur before another recall can be se-
lected.
To Disable a RKE Transmitter
Linked to Memory
1. Turn the ignition switch to the LOCK posi-
tion, and remove the key.
2. Press and release MEMORY button number
1. The system will recall any memory settings
stored in position 1. Wait for the system to
complete the memory recall before continuing
to Step 3.
3. Press and release the memory S (SET) but-
ton located on the driver’s door.
4. Within five seconds, press and release
MEMORY button 1 on the driver’s door.
5. Within five seconds, press and release the
UNLOCK button on the RKE transmitter.
To disable another RKE transmitter linked to
either memory position, repeat steps 1 through
5 for each RKE transmitter.
NOTE:
Once programmed, all RKE transmitters
linked to memory can be easily enabled or
disabled at one time. Refer to “Electronic
Vehicle Information Center (EVIC)/Customer-
Programmable Features” in “Understanding
Your Instrument Panel” for further informa-
tion.
Easy Entry/Exit SeatThis feature provides automatic driver’s seat
positioning which will enhance driver mobility
out of and into the vehicle.
There are two possible Easy Entry/Exit adjust-
ments available:
•
The seat cushion will move rearward ap-
proximately 2.5 in (60 mm), if the starting
position of the seat is greater than or equal to
2.67 in (68 mm) forward of the rear seat stop
when the key is removed from the ignition
switch. The seat will then move forward
approximately 2.5 in (60 mm) when the key is
placed into the ignition and turned out of the
LOCK position.
104