2011 INFINITI QX56 wheel

BRC-34
< SYSTEM DESCRIPTION >[WITH VDC]
SYSTEM
Transfer control unit is appli
ed to models with 4WD system.
INPUT SIGNAL AND OUTPUT SIGNAL
Major signal transmission between each unit via communication lines is shown in the following table.
*1: Communication line between yaw rate/side/decal G s ensor and ABS actuator and electric unit (control unit)
*2: Models with 4WD system
EBD FUNCTION
EBD FUNCTION : System DescriptionINFOID:0000000006222575
 By preventing rear wheel slip increase through rear wheel brake force (brake fluid pressure) control that is
electronically controlled when slight skip on front and r ear wheels are detected during braking, stability dur-
ing braking is improved.
JPFIC0184GB
Component Signal description
Yaw rate/side/decel G sensor Mainly transmits the following si
gnals to ABS actuator and electric unit (control unit) via com-
munication line
*1.
 Yaw rate signal
 Side G sensor signal
 Decel G sensor signal
Transfer control unit
*2Mainly transmits the following si gnals to ABS actuator and electric unit (control unit) via CAN
communication.
 Current 4WD mode signal
Combination meter Mainly receives
the following signals from ABS actuator and electric unit (control unit) via CAN
communication.
 ABS warning lamp signal
Revision: 2010 May2011 QX56

SYSTEMBRC-35
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
 EBD function is expanded and developed from conventi onal ABS function and corrects rear wheel brake
force to appropriate level by electronic control according to load weight (number of passengers).
 During braking, control unit portion compares slight slip on front and rear wheels by wheel speed sensor signal, transmits drive sig-
nal to actuator portion when rear wheel slip exceeds front wheel
slip for the specified value or more, and controls rear wheel brake
force (brake fluid pressure) so t hat increase of rear wheel slip is
prevented and slips on front wheel and rear wheel are nearly
equalized. ABS control is applied when slip on each wheel
increases and wheel speed is the threshold value of ABS control or
less.
 CONSULT-III can be used to diagnose the system diagnosis.
 Fail-safe function is adopted. When a malfunction occurs in EBD function, the control is suspended for VDC function, TCS function,
ABS function, EBD function, hill start assist function and brake lim-
ited slip differential (BLSD) func tion. The vehicle status becomes
the same as models without VDC function, TCS function, ABS
function, EBD function, hill start assist function and brake limited
slip differential (BLSD) function. Refer to BRC-25, "
Fail-safe".
JPFIC0142GB
JPFIC0143GB
Revision: 2010 May2011 QX56

SYSTEMBRC-37
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
SYSTEM DIAGRAM
INPUT SIGNAL AND OUTPUT SIGNAL
Major signal transmission between each unit via communication lines is shown in the following table.
*: Communication line between yaw rate/side/decal G s ensor and ABS actuator and electric unit (control unit)
BRAKE LIMITED SLIP DIFFERENTIAL (BLSD) FUNCTION
BRAKE LIMITED SLIP DIFFERENTIAL (BLSD) FUNCTION : System Description
INFOID:0000000006222577
 LH and RH driving wheel spin is always monitored. If necessary, appropriate brake force is independently
applied to LH or RH driving wheel so that one-sided wheel spin is avoided and traction is maintained. Mainly
starting ability is improved.
JPFIC0145GB
Component Signal description
Yaw rate/side/decel G sensor Mainly transmits the following signals to ABS actuator and electric unit (control unit) via com-
munication line *.
 Yaw rate signal
 Side G sensor signal
 Decel G sensor signal
ECM Mainly transmits the following signals to ABS actuator and electric unit (control unit) via CAN
communication.
 Accelerator pedal position signal
 Engine speed signal
Mainly receives the following signals from ABS actuator and electric unit (control unit) via CAN
communication.
 Target throttle position signal
TCM Mainly transmits the following signals to ABS actuator and electric unit (control unit) via CAN
communication.
 Shift position signal
Combination meter Mainly receives the following signals from ABS actuator and electric unit (control unit) via CAN
communication.
 VDC warning lamp signal
 VDC OFF indicator lamp signal
Revision: 2010 May2011 QX56

BRC-40
< SYSTEM DESCRIPTION >[WITH VDC]
DIAGNOSIS SYSTEM [
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
CONSULT-III FunctionINFOID:0000000006222578
APPLICATION ITEMS
CONSULT-III can display each diagnostic item using the diagnostic test modes as follows.
*: The following diagnosis information is erased by erasing.
DTC
 Freeze frame data (FFD)
ECU IDENTIFICATION
ABS actuator and electric unit (cont rol unit) part number can be read.
SELF DIAGNOSTIC RESULT
Refer to BRC-51, "DTC Index".
When “CRNT” is displayed on self-diagnosis result,
 The system is presently malfunctioning.
When “PAST” is displayed on self-diagnosis result, System malfunction in the past is detect ed, but the system is presently normal.
Freeze frame data (FFD)
DATA MONITOR
×: Applicable
Mode Function description
ECU identification Parts number of ABS actuator and electric unit (control unit) can be read.
Self Diagnostic Result Self-diagnostic results and freeze frame data can be read and erased quickly.
*
DATA MONITOR Input/Output data in the ABS actuator and electric unit (control unit) can be read.
ACTIVE TEST Diagnostic Test Mode in
which CONSULT-III drives some act uators apart from the ABS actuator and
electric unit (control unit) and also shifts some parameters in a specified range.
WORK SUPPORT Components can be quickly and accurately adjusted.
Item name Display item
IGN counter
(0 − 39) The number of times that ignition switch is tu
rned ON after the DTC is detected is displayed.
 When “0” is displayed: It indicates that the system is presently malfunctioning.
 When except “0” is displayed: It indicates that system malfunction in the past is detected, but the system is pres- ently normal.
NOTE:
Each time when ignition switch is turned OFF to ON, numerical number increases in 1 → 2 → 3...38 → 39. When
the operation number of times exceeds 39, the number do not increase and “39” is displayed until self-diagnosis
is erased.
Item (Unit) Monitor item selection
Note
INPUT SIGNALS MAIN ITEMS
FR LH SENSOR
[km/h (MPH)] ××Wheel speed calculated by front LH wheel sensor is dis-
played.
FR RH SENSOR
[km/h (MPH)] ××Wheel speed calculated by front RH wheel sensor is dis-
played.
RR LH SENSOR
[km/h (MPH)] ××
Wheel speed calculated by rear LH wheel sensor is dis-
played.
RR RH SENSOR
[km/h (MPH)] ××Wheel speed calculated by rear RH wheel sensor is dis-
played.
DECEL G-SEN
(G) ××
Decel G detected by decel G sensor is displayed.
Revision: 2010 May2011 QX56

DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
BRC-41
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
FR RH IN SOL
(On/Off) ×Operation status of front
RH wheel ABS IN valve is dis-
played.
FR RH OUT SOL
(On/Off) ×Operation status of front
RH wheel ABS OUT valve is dis-
played.
FR LH IN SOL
(On/Off) ×
Operation status of front LH wheel ABS IN valve is dis-
played.
FR LH OUT SOL
(On/Off) ×Operation status of front LH wheel ABS OUT valve is dis-
played.
RR RH IN SOL
(On/Off) ×
Operation status of rear RH wh eel ABS IN valve is displayed
RR RH OUT SOL
(On/Off) ×
Operation status of rear RH wheel ABS OUT valve is dis-
played.
RR LH IN SOL
(On/Off) ×Operation status of rear LH
wheel ABS IN valve is dis-
played.
RR LH OUT SOL
(On/Off) ×Operation status of rear LH
wheel ABS OUT valve is dis-
played.
EBD WARN LAMP
(On/Off) Brake warning lamp ON/OFF status is displayed.
(Note 1)
STOP LAMP SW
(On/Off)××
Stop lamp switch signal input status is displayed.
MOTOR RELAY
(On/Off) ×
ABS motor and motor relay status is displayed.
ACTUATOR RLY
(On/Off) ×
ABS actuator relay status is displayed.
ABS WARN LAMP
(On/Off) ×
ABS warning lamp ON/OFF status is displayed.
(Note 1)
OFF LAMP
(On/Off) ×
VDC OFF indicator lamp ON/OFF status is displayed.(Note 1)
OFF SW
(On/Off) ××
VDC OFF switch signal input status is displayed.
SLIP/VDC LAMP
(On/Off) ×
VDC warning lamp ON/OFF status is displayed.
(Note 1)
BATTERY VOLT
(V) ××Voltage supplied to ABS actuator and electric unit (control
unit) is displayed.
GEAR ××Current gear position judged from current gear position sig-
nal is displayed.
ENGINE SPEED
(tr/min) ××
Engine speed status is displayed.
YAW RATE SEN
(d/s) ××
Yaw rate detected by yaw rate sensor is displayed.
R POSI SIG
(On/Off) R range signal input status judged from R range signal is
displayed.
4WD MODE MON
(Note 2)
(AUTO/LOCK/##) ××
4WD control status is displayed.
N POSI SIG
(On/Off) N range signal input status judged from N range signal is
displayed.
CV1
(On/Off) Cut valve 1 operation status is displayed.
CV2
(On/Off) Cut valve 2 operation status is displayed.
SV1
(On/Off) Suction valve 1 operation status is displayed.
Item (Unit)
Monitor item selection
Note
INPUT SIGNALS MAIN ITEMS
Revision: 2010 May2011 QX56

BRC-46
< ECU DIAGNOSIS INFORMATION >[WITH VDC]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
ABS WARN LAMPWhen ABS warning lamp is ON
(Note 2)On
When ABS warning lamp is OFF
(Note 2)Off
OFF LAMP When VDC OFF indicator lamp is ON
(Note 2)On
When VDC OFF indicator lamp is OFF
(Note 2)Off
OFF SW VDC OFF switch ON On
VDC OFF switch OFF Off
SLIP/VDC LAMP When VDC warning lamp is ON or Blinking
(Note 2)On
When VDC warning lamp is OFF
(Note 2)Off
BATTERY VOLT Ignition switch ON 10 – 16 V
GEAR Driving 1 – 7
Depending on shift status
ENGINE SPEED Engine stopped 0 tr/min
Engine running Almost same reading as tachometer
YAW RATE SEN Vehicle stopped Approx. 0 d/s
Turning right Negative value
Turning left Positive value
R POSI SIG When selector lever is in the R position On
When selector lever is in the other position than R Off
4WD MODE MON
(Note 3)
When 4WD sift switch is AUTO position AUTO
When 4WD sift switch is 4H position LOCK
When 4WD sift switch is 4L position ##
N POSI SIG When selector lever is in the N position On
When selector lever is in the other position than N Off
CV1 Active On
Inactive Off
CV2 Active On
Inactive Off
SV1 Active On
Inactive Off
SV2 Active On
Inactive Off
STOP LAMP SW2 Brake pedal depressed On
Brake pedal not depressed Off
ACCEL POS SIG Never depress accelerator pedal
(with ignition switch ON)
0%
Depress accelerator pedal
(with ignition switch ON) 0 – 100%
SIDE G-SENSOR Vehicle stopped
Approx. 0 m/s
2
Right turn Negative value
Left turn Positive value
STR ANGLE SIG When driving straight 0
±2.5 °
When steering wheel is steered to LH by 90 °Approx. +90 °
When steering wheel is steered to RH by 90 °Approx. –90 °
Monitor item Condition Reference values in normal operation
Revision: 2010 May2011 QX56

BRC-48
< ECU DIAGNOSIS INFORMATION >[WITH VDC]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
VDC function, TCS function, hill start assist function and
brake limited slip differential (BLSD) function. How-
ever, ABS function and EBD function are operated normally.
ABS FUNCTION
ABS warning lamp and VDC warning lamp in combinati on meter turn ON when a malfunction occurs in system
[ABS actuator and electric unit (control unit)]. The c ontrol is suspended for VDC function, TCS function, ABS
function, hill start assist function and brake limited sl ip differential (BLSD) function. The vehicle status
becomes the same as models without VDC function, TCS f unction, ABS function, hill start assist function and
brake limited slip differential (BLSD) function. However, EBD function is operated normally.
NOTE:
ABS self-diagnosis sound may be heard the same as in the normal condition, because self-diagnosis is per-
formed when ignition switch turns ON and when vehicle initially starts.
EBD FUNCTION
ABS warning lamp, brake warning lamp and VDC warning lamp in combination meter turn ON when a mal-
function occurs in system [ABS actuator and electric unit (control unit)]. The control is suspended for VDC
function, TCS function, ABS function, EBD function, hill start assist function and brake limited slip differential
(BLSD) function. The vehicle status becomes the sa me as models without VDC function, TCS function, ABS
function, EBD function, hill star t assist function and brake limited slip differential (BLSD) function.
DTC Malfunction detected condition Fail-safe condition
C1101 When an open circuit is detected in rear RH wheel sensor circuit.
The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 EBD function (only when both 2 rear wheels are malfunctioning)
 hill start assist function
 Brake limited slip differential (BLSD) function
C1102 When an open circuit is detected in rear LH wheel sensor circuit.
C1103 When an open circuit is detected in front RH wheel sensor circuit.
C1104 When an open circuit is detected in front LH wheel sensor circuit.
C1105
 When power supply voltage of rear RH wheel sensor is low.
 When distance between rear RH wheel sensor and rear RH wheel sensor rotor is
large.
 When installation of rear RH wheel sensor or rear RH wheel sensor rotor is not normal.
C1106  When power supply voltage of rear LH wheel sensor is low.
 When distance between rear LH wheel sensor and rear LH wheel sensor rotor is
large.
 When installation of rear LH wheel sensor or rear LH wheel sensor rotor is not nor-
mal.
C1107  When power supply voltage of front RH wheel sensor is low.
 When distance between front RH wheel sensor and front RH wheel sensor rotor
is large.
 When installation of front RH wheel sensor or front RH wheel sensor rotor is not normal.
C1108  When power supply voltage of front LH wheel sensor is low.
 When distance between front LH wheel sensor and front LH wheel sensor rotor is
large.
 When installation of front LH wheel sensor or front LH wheel sensor rotor is not normal.
C1109  When ignition voltage is 10 V or less.
 When ignition voltage is 16 V or more. The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 EBD function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C 1111
 When a malfunction is detected in motor or motor relay.
 When a low pressure malfunction is detected in accumulator.
 When a malfunction is detected in accumulator pressure sensor.
Revision: 2010 May2011 QX56

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)BRC-49
< ECU DIAGNOSIS INFORMATION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C 111 5 When difference in wheel speed between any wheel and others is detected during
the vehicle is driven, because of installation of other tires than specified. The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C 111 6
 When stop lamp switch signal is not input when brake pedal depress.
 When stop lamp switch signal is not input when stop lamp relay operates.
C 111 8
*1When a malfunction is detected in transfer control unit system.
C1120 When a malfunction is detec ted in front LH ABS IN valve.
The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 EBD function
 hill start assist function
 Brake limited slip differential (BLSD) function
C1121 When a malfunction is detec
ted in front LH ABS OUT valve.
C1122 When a malfunction is detected in front RH ABS IN valve.
C1123 When a malfunction is det ected in front RH ABS OUT valve.
C1124 When a malfunction is detected in rear LH ABS IN valve.
C1125 When a malfunction is detected in rear LH ABS OUT valve.
C1126 When a malfunction is det ected in rear RH ABS IN valve.
C1127 When a malfunction is detected in rear RH ABS OUT valve.
C1130 When a malfunction is detected in ECM system. The following functions are sus-
pended.
 VDC function
 TCS function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C1140 When a malfunction is detected in actuator relay. The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 EBD function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C1142
*2When a malfunction is detected in master cylinder pressure sensor or control pres-
sure sensor. The following functions are sus-
pended.
 VDC function
 TCS function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C1143 When a malfunction is detected in steering angle sensor.
C1144 When neutral position adjustment of steering angle sensor is not complete.
C1145
 When a malfunction is detected in yaw rate signal.
 When yaw rate signal is not continuously received for 2 seconds or more.
 When side G signal is not continuously received for 2 seconds or more.
 When decel G signal is not continuously received for 2 seconds or more.
The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C1146 When a malfunction is detected in side/decel G signal.
C1155
 When brake fluid level low signal is detected.
 When an open circuit is detected in brake fluid level switch circuit.
C1160 When calibration of yaw rate/side/decal G sensor is not complete.
C1164 When a malfunction is detected in cut valve 1. The following functions are sus- pended.
 VDC function
 TCS function
 ABS function
 EBD function
 hill start assist function
 Brake limited slip differential (BLSD) function
C1165 When a malfunction is detected in cut valve 2.
C1166 When a malfunction is detected in suction valve 1.
C1167 When a malfunction is detected in suction valve 2. DTC Malfunction detected condition Fail-safe condition
Revision: 2010 May2011 QX56