2011 INFINITI QX56 battery

EC-66
< SYSTEM DESCRIPTION >[VK56VD]
DIAGNOSIS SYSTEM (ECM)
A/F ALPHA-B1
% The mean value of the air-fuel ratio feedback cor-
rection factor per cycle is indicated.  When the engine is stopped,
a certain value is indicated.
 This data also includes the data for the air-fuel ratio
learning control.
 When engine is running, specification range is indicat-
ed in “SPEC”.
A/F ALPHA-B2
COOLAN TEMP/S
°C or °F  The engine coolant temperature (determined by
the signal voltage of the engine coolant tempera-
ture sensor) is displayed.  When the engine coolant
temperature sensor is open
or short-circuited, ECM en-
ters fail-safe mode. The en-
gine coolant temperature
determined by the ECM is
displayed.
A/F SEN1 (B1) V The A/F signal computed from the input signal of
the air fuel ratio (A/F) sensor 1 is displayed.
A/F SEN1 (B2)
HO2S2 (B1)
V The signal voltage of the heated oxygen sensor 2
is displayed.
HO2S2 (B2)
HO2S2 MNTR (B1)
RICH/LEAN Display of heated oxygen sensor 2 signal:
RICH: means the amount of oxygen after three
way catalyst is relatively small.
LEAN: means the amount of oxygen after three
way catalyst is relatively large.  When the engine is stopped,
a certain value is indicated.
HO2S2 MNTR (B2)
VHCL SPEED SE km/h or mph  The vehicle speed computed from the vehicle
speed signal sent from combination meter is dis-
played.
BATTERY VOLT V  The power supply voltage of ECM is displayed.
ACCEL SEN 1
V The accelerator pedal position sensor signal volt-
age is displayed.  ACCEL SEN 2 signal is con-
verted by ECM internally.
Thus, they differs from ECM
terminal voltage signal.
ACCEL SEN 2
TP SEN 1-B1
V The throttle position sensor signal voltage is dis-
played.  TP SEN 2-B1 signal is con-
verted by ECM internally.
Thus, they differs from ECM
terminal voltage signal.
TP SEN 2-B1
FUEL T/TMP SE
°C or °F  The fuel temperature (determined by the signal
voltage of the fuel tank temperature sensor) is dis-
played.
EVAP SYS PRES V  The signal voltage of EVAP control system pres-
sure sensor is displayed.
FUEL LEVEL SE V  The signal voltage of the fuel level sensor is dis-
played.
START SIGNAL ON/OFF  Indicates start signal status [ON/OFF] computed
by the ECM according to the signals of engine
speed and battery voltage.  After starting the engine,
[OFF] is displayed regard-
less of the starter signal.
CLSD THL POS ON/OFF  Indicates idle position [ON/OFF] computed by
ECM according to the accelerator pedal position
sensor signal.
AIR COND SIG ON/OFF  Indicates [ON/OFF] condition of the air conditioner
switch as determined by the air conditioner signal.
PW/ST SIGNAL ON/OFF  [ON/OFF] condition of the power steering system
(determined by the signal voltage of the power
steering pressure sensor signal) is indicated.
Monitored item Unit Description Remarks
Revision: 2010 May2011 QX56

EC-68
< SYSTEM DESCRIPTION >[VK56VD]
DIAGNOSIS SYSTEM (ECM)
VEHICLE SPEED km/h or mph The vehicle speed computed from the vehicle
speed signal sent from TCM is displayed.
IDL A/V LEARN YET/CMPLT  Displays the condition of Idle Air Volume Learning
YET: Idle air volume learning has not been per-
formed yet.
CMPLT: Idle air volume learning has already been
performed successfully.
TRVL AFTER MIL km or mile  Distance traveled while MIL is activated.
SNOW MODE SW ON/OFF  Indicates [ON/OFF] condition from the snow mode
switch signal.
ENG OIL TEMP °C or °F  The engine oil temperature (determined by the sig-
nal voltage of the engine oil temperature sensor) is
displayed.
MAIN SW ON/OFF  Indicates [ON/OFF] condition from MAIN switch
signal.
CANCEL SW ON/OFF  Indicates [ON/OFF] condition from CANCEL
switch signal.
RESUME/ACC SW ON/OFF  Indicates [ON/OFF] condition from RESUME/AC-
CELERATE switch signal.
SET SW ON/OFF  Indicates [ON/OFF] condition from SET/COAST
switch signal.
BRAKE SW1 ON/OFF  Indicates [ON/OFF] condition from ASCD brake
switch signal.
BRAKE SW2 ON/OFF  Indicates [ON/OFF] condition of stop lamp switch
signal.
DIST SW ON/OFF  Indicates [ON/OFF] condition from DISTANCE
switch signal.
CRUISE LAMP ON/OFF  Indicates [ON/OFF] condition of CRUISE indicator
determined by the ECM according to the input sig-
nals.
AC EVA TEMP °C or °F  Indicates A/C evaporator temperature sent from A/
C auto amp.
AC EVA TARGET °C or °F  Indicates target A/C evaporator temperature sent
from A/C auto amp.
FAN DUTY %  Indicates a command value for cooling fan. The
value is calculated by ECM based on input signals.
ALT DUTY %  Indicates the duty ratio of the power generation
command value. The ratio is calculated by ECM
based on the battery current sensor signal.
BAT CUR SEN mV  The signal voltage of battery current sensor is dis-
played.
A/F ADJ-B1
— Indicates the correction of a factor stored in ECM.
The factor is calculated from the difference be-
tween the target air-fuel ratio stored in ECM and
the air-fuel ratio calculated from A/F sensor 1 sig-
nal.
A/F ADJ-B2
P/N POSI SW ON/OFF
 Indicates [ON/OFF] condition from the park/neutral
position (PNP) signal.
INT/A TEMP SE °C or °F  The intake air temperature (determined by the sig-
nal voltage of the intake air temperature sensor) is
indicated.
AC PRESS SEN V  The signal voltage from the refrigerant pressure
sensor is displayed.
FUEL PRES SEN MPa  Indicates the fuel rail pressure computed by ECM
according to the input signals
Monitored item Unit Description Remarks
Revision: 2010 May2011 QX56

DIAGNOSIS SYSTEM (ECM)EC-69
< SYSTEM DESCRIPTION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
FUEL INJ B1 msec
 ECM-calculated injection pulse width of the fuel in-
jector on the Bank 1 side.
FUEL INJ B2 msec  ECM-calculated injection pulse width of the fuel in-
jector on the Bank 2 side.
INT/V TIM (B1) °CA  Indicates [ °CA] of intake camshaft advance angle.
INT/V TIM (B2)
MAP SENSOR V  The signal voltage from the manifold absolute
pressure (MAP) sensor is displayed.
EVAP LEAK DIAG YET/CMPLT  Indicates the condition of EVAP leak diagnosis.
YET: EVAP leak diagnosis has not been performed
yet.
CMPLT: EVAP leak diagnosis has been performed
successfully.
EVAP DIAG READY ON/OFF  Indicates the ready condition of EVAP leak diagno-
sis.
ON: Diagnosis has been ready condition.
OFF: Diagnosis has not been ready condition.
VVEL LEARN YET/DONE  Display the conditi
on of VVEL learning
YET: VVEL learning has not been performed yet.
DONE: VVEL learning has already been per-
formed successfully.
VVEL SEN LEARN-B1 V  Indicates the VVEL learning value.
VVEL SEN LEARN-B2
VVEL POSITION SEN-B1 V The VVEL control shaft position sensor signal volt-
age is displayed.
VVEL POSITION SEN-B2
VVEL TIM-B1
deg  Indicates [deg] of VVEL control shaft angle.
VVEL TIM-B2
FPCM HI/MID/LOW/
OFF  The control condition of the fuel pump control mod-
ule (FPCM) (determined by ECM according to the
input signals) is indicated.
BAT TEMP SEN V  The signal voltage from the battery temperature
sensor is displayed.
COOLING FAN SPD rpm  Displays a cooling fan speed from a signal of elec-
trically-controlled cooling fan coupling.
THRTL STK CNT B1* — —
HO2 S2 DIAG2(B1)* INCMP/CM-
PLT  Indicates DTC P0139 self-diagnosis (slow re-
sponse) condition.
INCMP: Self-diagnosis is incomplete.
CMPLT: Self-diagnosis is complete.
HO2 S2 DIAG2(B2)* INCMP/CM-
PLT  Indicates DTC P0159 self-diagnosis (slow re-
sponse) condition.
INCMP: Self-diagnosis is incomplete.
CMPLT: Self-diagnosis is complete.
FUEL INJ TIMG deg  Indicates the fuel injection timing computed by
ECM according to the input signals.
H/P FUEL PUMP DEG deg  Displays ECM-calculated fuel discharge position
of the high pressure fuel pump.
FUEL PRES SEN V mV  The signal voltage of FRP sensor is displayed.
L/FUEL PRES SEN MPa  Displays a pressure value calculated from a low
fuel pressure sensor voltage.
L/FUEL PRES SEN V mV  The signal voltage of low fuel pressure sensor is
displayed.
Monitored item Unit Description Remarks
Revision: 2010 May2011 QX56

EC-70
< SYSTEM DESCRIPTION >[VK56VD]
DIAGNOSIS SYSTEM (ECM)
*: The item is indicated, but not used.
NOTE:
Any monitored item that does not match the vehicle being diagnosed is deleted from the display automatically.
ACTIVE TEST MODE
Test Item
ECM TEMP 1
°C or °F  Displays a temperature calculated from a signal of
ECM temperature sensor 1.
ECM TEMP 2 °C or °F  Displays a temperature calculated from a signal of
ECM temperature sensor 2.
FUEL PUMP DUTY %  The control condition of the fuel pump control mod-
ule (FPCM) (determined by ECM according to the
input signals) is indicated.
Monitored item Unit Description Remarks
TEST ITEM CONDITION JUDGMENT CHECK ITEM (REMEDY)
VENT CON-
TROL/V  Ignition switch: ON (Engine
stopped)
 Turn solenoid valve ON and OFF with the CONSULT-III and listen
to operating sound. Solenoid valve makes an operating
sound.
 Harness and connectors
 Solenoid valve
ENG COOLANT
TEMP  Engine: Return to the original
non-standard condition
 Change the engine coolant tem- perature using CONSULT-III. If malfunctioning symptom disap-
pears, see CHECK ITEM.  Harness and connectors
 Engine coolant temperature sen-
sor
 Fuel injector
FUEL INJEC-
TION  Engine: Return to the original
non-standard condition
 Change the amount of fuel injec- tion using CONSULT-III. If malfunctioning symptom disap-
pears, see CHECK ITEM.
 Harness and connectors
 Fuel injector
 Air fuel ratio (A/F) sensor 1
FUEL/T TEMP
SEN  Change the fuel tank temperature using CONSULT-III.
PURG VOL
CONT/V  Engine: After warming up, run en-
gine at 1,500 rpm.
 Change the EVAP canister purge
volume control solenoid valve
opening percent using CON-
SULT-III. Engine speed changes according to
the opening percent.
 Harness and connectors
 Solenoid valve
FAN DUTY CON-
TROL* Ignition switch: ON
 Change duty ratio using CON-
SULT-III. Cooling fan speed changes.  Harness and connectors
 Cooling fan motor
 Cooling fan relay
 Cooling fan control module
 IPDM E/R
ALTERNATOR
DUTY Engine: Idle
 Change duty ratio using CON-
SULT-III. Battery voltage changes.  Harness and connectors
 IPDM E/R
Alternator
POWER BAL-
ANCE  Engine: After warming up, idle the
engine.
 A/C switch OFF
 Selector lever: P or N
 Cut off each injector signal one at a time using CONSULT-III. Engine runs rough or stops.
 Harness and connectors
 Compression
 Fuel injector
 Power transistor
Spark plug
 Ignition coil
IGNITION TIM-
ING  Engine: Return to the original
non-standard condition
 Timing light: Set
 Retard the ignition timing using
CONSULT-III. If malfunctioning symptom disap-
pears, see CHECK ITEM.
 Perform Idle Air Volume Learning.
Revision: 2010 May2011 QX56

EC-72
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
ECU DIAGNOSIS INFORMATION
ECM
Reference ValueINFOID:0000000006217730
VALUES ON THE DIAGNOSIS TOOL
NOTE:
 Specification data are reference values.
 Specification data are output/input values which are
detected or supplied by the ECM at the connector.
* Specification data may not be directly relat ed to their components signals/values/operations.
i.e. Adjust ignition timing with a timing light before monitoring IGN TIMING, because the monitor may show
the specification data in spite of the ignition timing not being adjusted to the specification data. This IGN TIM-
ING monitors the data calculated by the ECM accordi ng to the signals input from the camshaft position sen-
sor and other ignition timing related sensors.
CONSULT-III MONITOR ITEM
Monitor Item Condition Values/Status
ENG SPEED  Run engine and compare CONSULT-III value with the tachometer indication. Almost the same speed as
the tachometer indication
MAS A/F SE-B1 See EC-161, "
Description".
B/FUEL SCHDL See EC-161, "
Description".
A/F ALPHA-B1 See EC-161, "
Description".
A/F ALPHA-B2 See EC-161, "
Description".
COOLAN TEMP/S  Ignition switch: ON Indicates engine coolant
temperature
A/F SEN1 (B1)  Engine: After warming up Maintaining engine speed at 2,000 rpm Fluctuates around 1.5 V
A/F SEN1 (B2)  Engine: After warming up Maintaining engine speed at 2,000 rpm Fluctuates around 1.5 V
HO2S2 (B1)  Revving engine from idle up to 3,000 rpm quickly after the following condi-
tions are met.
- Engine: After warming up
- After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and at idle for 1 minute under no load 0 - 0.3 V
⇔ Approx. 0.6 - 1.0
V
HO2S2 (B2)  Revving engine from idle up to 3,000 rpm quickly after the following condi-
tions are met.
- Engine: After warming up
- After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and at idle for 1 minute under no load 0 - 0.3 V
⇔ Approx. 0.6 - 1.0
V
HO2S2 MNTR (B1)  Revving engine from idle up to 3,000 rpm quickly after the following condi-
tions are met.
- Engine: After warming up
- After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and
at idle for 1 minute under no load LEAN
⇔ RICH
HO2S2 MNTR (B2)  Revving engine from idle up to 3,000 rpm quickly after the following condi-
tions are met.
- Engine: After warming up
- After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and at idle for 1 minute under no load LEAN
⇔ RICH
VHCL SPEED SE  Turn drive wheels and compare CONSULT-III value with the speedometer in-
dication. Almost the same speed as
speedometer indication
BATTERY VOLT  Ignition switch: ON (Engine stopped) 11 - 14 V
ACCEL SEN 1  Ignition switch: ON
(Engine stopped) Accelerator pedal: Fully released 0.65 - 0.87 V
Accelerator pedal: Fully depressed 4.3 - 4.8 V
ACCEL SEN 2*
1 Ignition switch: ON (Engine stopped) Accelerator pedal: Fully released 0.56 - 0.96 V
Accelerator pedal: Fully depressed 4.0 - 4.8 V
Revision: 2010 May2011 QX56

ECM
EC-75
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
BRAKE SW2
(Stop lamp switch)
 Ignition switch: ON Brake pedal: Fully released OFF
Brake pedal: Slightly depressed ON
DIST SW  Ignition switch: ON DISTANCE switch: Pressed ON
DISTANCE switch: Released OFF
CRUISE LAMP  Ignition switch: ON MAIN switch: Pressed at the 1st time
→
at the 2nd time ON
→ OFF
AC EVA TEMP  Engine: Running Indicates A/C evaporator
temperature sent from“uni-
fied meter and A/C amp.”.
AC EVA TARGET  Engine: Running Indicates target A/C evapo-
rator temperature sentfrom
“unified meter and A/C
amp.”.
FAN DUTY  Engine: Running 0 - 100%
ALT DUTY  Engine: Idle 0 - 80%
BAT CUR SEN  Engine speed: Idle
 Battery: Fully charged*
2
 Selector lever: P or N position
 A/C switch: OFF
No load Approx. 2,600 - 3,500 mV
A/F ADJ-B1  Engine: Running −0.330 - 0.330
A/F ADJ-B2  Engine: Running −0.330 - 0.330
P/N POSI SW  Ignition switch: ON Selector lever: P or N ON
Selector lever: Except above position OFF
INT/A TEMP SE  Ignition switch: ON Indicates intake air temper-
ature
AC PRESS SEN  Engine: Idle
 Both A/C switch and blower fan switch: ON (Compressor operates) 1.0 - 4.0 V
FUEL PRES SEN  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 2.74 Mpa
2,000 rpm Approx. 3.0 Mpa
FUEL INJ B1  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 1.4 msec
2,000 rpm Approx. 1.0 msec
FUEL INJ B2  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 1.4 msec
2,000 rpm Approx. 1.0 msec
INT/V TIM (B1)  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle
−5 - 5 °CA
2,000 rpm Approx. 0 - 30 °CA
INT/V TIM (B2)  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle
−5 - 5 °CA
2,000 rpm Approx. 0 - 30 °CA
MAP SENSOR  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 1.0 V
2,000 rpm Approx. 1.35 V
EVAP LEAK DIAG  Ignition switch: ON Indicates the condition of
EVAP leak diagnosis.
Monitor Item Condition Values/Status
Revision: 2010 May2011 QX56

EC-76
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
EVAP DIAG READY  Ignition switch: ON Indicates the ready condi-
tion of EVAP leak diagnosis.
VVEL LEARN  Ignition switch: OFF
→ ON
(After warming up) VVEL learning has no
t been performed
yet. YET
VVEL learning has already been per-
formed successfully. DONE
VVEL SEN LEARN-B1  VVEL learning has already been performed successfully Approx. 0.30 - 0.80 V
VVEL SEN LEARN-B2  VVEL learning has already been performed successfully Approx. 0.30 - 0.80 V
VVEL POSITION SEN-
B1  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 0.25 - 1.50 V
When revving engine up to 2,000 rpm
quickly
Approx. 0.25 - 4.75 V
VVEL POSITION SEN-
B2  Engine: After warming up
 Selector lever: P or N position
 Air conditioner switch: OFF
No load Idle Approx. 0.25 - 1.50 V
When revving engine up to 2,000 rpm
quickly
Approx. 0.25 - 4.75 V
VVEL TIM-B1  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 0 - 23 deg
When revving engine up to 2,000 rpm
quickly
Approx. 0 - 90 deg
VVEL TIM-B2  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 0 - 23 deg
When revving engine up to 2,000 rpm
quickly
Approx. 0 - 90 deg
FPCM  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load  Engine: Cranking HI
 Revving engine from idle to 4,000 rpm
quickly MID
 Engine: Idle
 Engine coolant temperature: More than 10 °C (50 °F) LOW
BAT TEMP SEN  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle
Indicates the temperature
around the battery.
COOLING FAN SPD  Engine speed: Idle
 Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Water temp: Less than 98
°C Approx. 100 – 200 rpm
Water temp: More than 98 °C Approx. 600 – 700 rpm
THRTL STK CNT B1 NOTE:
The item is indicated, but not used. —
HO2 S2 DIAG2(B1) NOTE:
The item is indicated, but not used.
—
HO2 S2 DIAG2(B2) NOTE:
The item is indicated, but not used. —
FUEL INJ TIMG Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 16 deg
2,000 rpm Approx.
−170 deg
H/P FUEL PUMP DEG  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 211.0 deg
2,000 rpm Approx. 206.0 deg
Monitor Item Condition Values/Status
Revision: 2010 May2011 QX56

ECM
EC-77
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
*1: Accelerator pedal position sensor 2 signal and throttle position sensor 2 signal are converted by ECM internally. Thus, the
y differ
from ECM terminals voltage signal.
*2: Before measuring the terminal voltage, confirm that the battery is fully charged. Refer to PG-159, "
How to Handle Battery".
TERMINAL LAYOUT
PHYSICAL VALUES
NOTE:
 Specification data are reference values and are measured between each terminals.
 Pulse signal is measured by CONSULT-III.
FUEL PRES SEN V Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 1150 mV
2,000 rpm Approx. 1200 mV
L/FUEL PRES SEN  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 0.45 MPa
2,000 rpm Approx. 0.45 MPa
L/FUEL PRES SEN V  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 3250 mV
3,000 rpm Approx. 3100 mV
ECM TEMP 1  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle
Indicates the temperature of
ECM internal circuit 1.
ECM TEMP 2  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle
Indicates the temperature of
ECM internal circuit 2.
FUEL PUMP DUTY  Engine: After warming up
 Shift lever: P or N
 Air conditioner switch: OFF
No load Engine speed: Idle 30 - 40%
Monitor Item Condition Values/Status
JPBIA3371ZZ
Revision: 2010 May2011 QX56