2011 INFINITI QX ECO mode

Title Search (DVD-VIDEO) :
A scene that belongs to a specified title will be
displayed each time the “+” side or “” side is
selected.
10 Key Search (DVD-VIDEO, VIDEO-CD, CD-DA) :
Select the “10 Key Search” key and push the
ENTER button to open the number entry screen.
Input the number you want to search for and
select the “OK” key with the INFINITI controller.
Then push the ENTER button. The specified
Title/Chapter or Group/Track will be played.
Angle (DVD-VIDEO) :
If the DVD contains different angles (such as
moving images), the current image angle can be
switched to another one.
Select the “Angle” key and push the ENTER
button. When the “+” side or “” side is
selected, the angle will change.
Angle Mark (DVD-VIDEO) :
When this item is turned on, an angle mark will
be shown on the bottom of the screen if the
scene can be seen from a different angle.Menu Skip (DVD-VIDEO) :
DVD menus are automatically configured and
the contents will be played directly when the
“Menu Skip” key is turned on. Note that some
discs may not be played directly even if this
item is turned on.
CM Skip (DVD-VIDEO) :
The amount of seconds for CM Skip can be set
to 15, 30 or 60 seconds.
DRC (DVD-VIDEO) :
DRC (Dynamic Range Compression) allows tun-
ing of the dynamic range of sound recorded in
the Dolby Digital format.
DVD Language (DVD-VIDEO, VIDEO-CD) :
Select the “DVD Language” key and push the
ENTER button to open the number entry screen.
Input the number corresponding to the pre-
ferred language and select the “OK” key with
the INFINITI controller. Then push the ENTER
button. The DVD top menu language will be
changed to the one selected.
Display :
Adjust the image quality of the screen, select
the preferred adjustment items and push the
ENTER button.Audio :
Choose the preferred language using the
INFINITI controller and push the ENTER button.
Subtitle (DVD-VIDEO) :
Choose the preferred language using the
INFINITI controller and push the ENTER button.
To turn off the subtitles, push and hold the
ENTER button until a beep sounds.
Display Mode (DVD-VIDEO, VIDEO-CD) :
Choose from the “Full”, “Wide”, “Normal” or
“Cinema” mode using the INFINITI controller
and push the ENTER button again.
Play Mode :
Choose the preferred play mode using the
INFINITI controller and push the ENTER button.
Remote controller operation
Use the remote controller to adjust the follow-
ing items.
Rear display ON/OFF :
The rear displays can be activated or deacti-
vated individually.
To activate or deactivate the rear displays, push
the preferred side (L or R) of the “ON·OFF”
button on the remote controller.
4-92Monitor, climate, audio, phone and voice recognition systems

Joystick :
Use the joystick
to select the items
displayed on the rear screen.
ENTER button :
Push the ENTER
button to make the
selected item complete on the rear screen.
BACK button :
Push to go back to the previous screen or cancel
the selection.
DVD mode :
To select the DVD mode, push the DVD button.
AUX mode :
The AUX (auxiliary input jacks) modes can be
activated or deactivated individually. To acti-
vate the AUX mode, push the preferred side (L
or R) of the AUX button. Push the AUX button
again and deactivate the AUX mode and display
another mode.
Volume :
To control the volume level, push the VOL
button
or. Display :
Display settings can be set individually for the
right and left screens.
Push the preferred side (L or R) of the DISP
button to adjust the rear display settings.
Sound :
To change the language, push the SOUND but-
ton. Each time the button is pushed, the lan-
guage will change to each language stored in
the DVD.
Track/Channel :
Push to skip to the previous or next DVD scene
selection.
Keypad :
: PLAY/PAUSE button
: STOP button
: FORWARD button
: REWIND button
: FORWARD button for commercial skip
(for DVD-VIDEO and DVD-VR) or still
images (for DVD-AUDIO)
: REWIND button for commercial skip (forDVD-VIDEO and DVD-VR) or still images
(for DVD-AUDIO)
Rear display settings
To adjust rear display setting, select the pre-
ferred key and push the ENTERbutton.
The following settings are available:
Aspect :
Select the display size from “CINEMA”, “WIDE”,
“FULL” or “NORMAL” using the joystick on the
remote controller.
Picture Mode :
To adjust the display brightness automatically,
select the “Brightness” key and then select
from “DARKER”, “NORMAL” or “BRIGHTER”.
When adjusting manually, select “OFF” and
adjust using the joystick on the remote control-
ler and tilt the joystick to the right or left.
To adjust tint, color, contrast or black level,
select a key using the joystick on the remote
controller and tilt the joystick to the right or left.
Push the BACK button on the remote controller
to apply the settings and return to the previous
display.
To return the adjustment levels to the default
value, select “Execute” next to “Initialization”
using the joystick on the remote controller and
push the ENTER
button. The “Execute”
key is deactivated when the picture mode set-
tings are already in the default value.
Monitor, climate, audio, phone and voice recognition systems4-93

Color System :
To choose the color system, select from “NTSC”,
“PAL”, “PAL-60”, “PAL-M”, “PAL-N” or “AUTO”
using the joystick on the remote controller and
tilt the joystick to the right or left.
3D Y/C filter :
Set to ON/OFF using the joystick on the remote
controller. When turned on, small characters
and an outline of the shapes will be displayed
more clearly than when turned off.
AUX Volume Setting :
To set the AUX volume, select from “HIGH”,
“LOW” or “MIDDLE” using the joystick on the
remote controller and tilt the joystick to the
right or left.
OPERATING TIPS
●The images from a device that is connected
to the rear auxiliary input jacks cannot be
viewed on the front displays.
● It is not possible to switch the source to USB
(if so equipped) or DVD using the remote
controller when the rear display is in the AUX
mode. Push the AUX (L)/(R) button in the
remote controller and turn off the AUX mode,
and then push the preferred mode switch. ●
It is not possible to display different video
files, such as DVD or video files in the USB
memory, on the front and rear displays at
the same time (models with navigation sys-
tem).
● It is not possible to play an audio file and a
video file in the same USB memory at the
same time (models with navigation system).
Multiple source display
It is possible to play different sources on each
display. The following example shows how to
operate multiple sources.
1. Display a video file in the front display by selecting the DVD mode.
2. Push the L side on the power ON·OFF button on the remote controller. The left
rear display comes on and the DVD screen
will be displayed.
3. Push the R side on the power ON·OFF button on the remote controller. The right
rear display comes on and the DVD screen
will be displayed. 4. Switch the source on the front display to
an audio source. The sound from the
speakers switches according to the front
display. The rear display continues to
display the DVD.
5. Turn on a pair of headphones and listen to the DVD on the rear displays using the
headphones.
6. Connect an auxiliary device into the AUX jacks and push the AUX (L) or AUX (R)
button on the remote controller. The se-
lected side of the rear display turns to the
AUX mode. The other rear display contin-
ues to display the DVD.
7. Turn on the other pair of headphones. If the sound from the headphones is not
from the AUX jacks, switch the channel
with the channel select switch on the
headphones.
4-94Monitor, climate, audio, phone and voice recognition systems

CARE AND MAINTENANCE
Use a lightly dampened, lint free cloth to clean
the surfaces of your Dual Head Restraint DVD
System (DVD player face, screen, remote con-
troller, etc.).
CAUTION
●Do not use any solvents or cleaning solu-
tions when cleaning the video system.
● Do not use excessive force on the monitor
screen.
● Avoid touching or scratching the monitor
screen as it may become dirty or damaged.
● Do not attempt to operate the system in ex-
treme temperature conditions [below 4°F
(20°C) and above 158°F (70°C)].
● Do not attempt to operate the system in ex-
treme humidity conditions (less than 10% or
more than 75%). When installing a car phone or a CB radio in
your INFINITI, be sure to observe the following
cautions, otherwise the new equipment may
adversely affect the electronic control modules
and electronic control system harness.
WARNING
●
A cellular telephone should not be used
while driving so full attention may be given
to vehicle operation. Some jurisdictions pro-
hibit the use of cellular telephones while
driving.
● If you must make a call while your vehicle is
in motion, the hands-free cellular phone op-
erational mode (if so equipped) is highly rec-
ommended. Exercise extreme caution at all
times so full attention may be given to ve-
hicle operation.
● If a conversation in a moving vehicle requires
you to take notes, pull off the road to a safe
location and stop your vehicle before doing
so.
CAUTION
● Keep the antenna as far away as possible
from the electronic control modules.
● Keep the antenna wire more than 8 in (20 cm)
away from the electronic control system har-
ness. Do not route the antenna wire next to
any harness.
● Adjust the antenna standing-wave ratio as
recommended by the manufacturer.
● Connect the ground wire from the CB radio
chassis to the body.
● For details, consult an INFINITI retailer.
CAR PHONE OR CB RADIO
Monitor, climate, audio, phone and voice recognition systems4-95

5. Select the “Call” key to start dialing thenumber.
There are different methods to make a call.
Select one of the following options instead of
“Handset Phonebook” in step 2 above.
● Vehicle Phonebook
Select an entry stored in the Vehicle’s
Phonebook.
● Call History
Select an outgoing, incoming or missed call
downloaded from your cell phone (depend-
ing on your phone’s compatibility). ●
Dial Number
Input the phone number manually using the
keypad displayed on the screen. (See “HOW
TO USE TOUCH SCREEN” earlier in this sec-
tion.)
RECEIVING A CALL
When you hear a phone ring, the display will
change to the incoming call mode. To receive a
call, perform one of the following procedures
listed below.
a) Select the “Answer” key.
b) Push the
button on the steering
wheel.
There are some options available when receiv-
ing a call. Select one of the following displayed
on the screen.
● Answer
Accept an incoming call to talk.
SAA2621SAA2525
4-102Monitor, climate, audio, phone and voice recognition systems

●Hold Call
Put an incoming call on hold.
● Reject Call
Reject an incoming call.
To finish the call, perform one of the follow-
ing procedures listed below.
a) Select the “Hang up” key.
b) Push the
button on the steering
wheel.
DURING A CALL
There are some options available during a call.
Select one of the following displayed on the
screen if necessary.
● Hang up
Finish the call.
● Use Handset
Transfer the call to the cellular phone.
● Mute
Mute your voice to the person. ●
Keypad
Using the touch tone, send digits to the
connected party for using services such as
voicemail.
● Cancel Mute
This will appear after “Mute” is selected.
Mute will be canceled.
To adjust the person’s voice to be louder or
quieter, push the volume control switch (+ or )
on the steering wheel or turn the volume control
knob on the instrument panel while talking on
the phone. This adjustment is also available in
the SETTING mode.
SAA2526
Monitor, climate, audio, phone and voice recognition systems4-103

INFINITI Voice Recognition allows hands-free
operation of the Phone, Navigation, Information
and Audio systems in one of two modes, Stan-
dard Mode or Alternate Command Mode.
In Standard Mode, commands that are available
are always shown on the display and an-
nounced by the system. You can complete your
desired operation by simply following the
prompts given by the system. (See “INFINITI
VOICE RECOGNITION STANDARD MODE” later in
this section for details.)
For advanced operation, you can use the Alter-
nate Command Mode. (See “INFINITI VOICE REC-
OGNITION ALTERNATE COMMAND MODE” later
in this section for details.) When this mode is
active, an expanded list of commands can be
spoken after pushing the TALK
switch,
and the voice command menu prompts are
turned off. Review the expanded command list,
which is available when this mode is active.
Note that in this mode the recognition success
rate may be affected as the number of available
commands and the ways of speaking each
command are increased. To switch one mode to another, see each mode
description later in this section.
To improve the recognition success rate when
Alternate Command Mode is active, try using
the Speaker Adaptation Function available in
that mode. Otherwise, it is recommended that
Alternate Command Mode be turned off and
Standard Mode be used for the best recognition
performance.
For the voice commands for the navigation
system, refer to the Navigation System Owner’s
Manual of your vehicle.
INFINITI VOICE RECOGNITION
STANDARD MODE
The following section is applicable when the
Standard Mode is activated.
The Standard Mode enables you to complete
the desired operation by simply following the
prompts that appear on the display and also are
announced by the system.
Activating Standard Mode
When the Alternate Command Mode is active,
perform the following steps to switch to the
Standard Mode.
1. Push the SETTING button on the instru-
ment panel.
2. Select the “Others” key.
3. Select the “Voice Recognition” key.
SAA2529
INFINITI VOICE RECOGNITION SYSTEM
4-106Monitor, climate, audio, phone and voice recognition systems

4. Select the “Alternate Command Mode”key.
5. The indicator turns off and the Standard Mode activates.
Displaying user guide
If you use the INFINITI Voice Recognition system
for the first time or you do not know how to
operate it, you can display the User Guide for
confirmation.
You can confirm how to use voice commands by
accessing a simplified User Guide, which con-
tains basic instructions and tutorials for several
voice commands.
1. Push the INFO button on the instrumentpanel.
2. Select the “Others” key.
3. Select the “Voice Recognition” key.
4. Select the “User Guide” key.
5. Select a preferred item.
You can skip steps 1 and 3 above if you say
“Help”. Available items :
●
Getting Started
Describes the basics of how to operate the
INFINITI Voice Recognition system.
● Let’s Practice
Mode that allows practicing by following the
instructions of the system voice.
● Using the Address Book
Tutorial for entering a destination by using
the Address Book.
● Finding a Street Address (if so equipped)
Tutorial for entering a destination by street
address.
● Placing Calls
Tutorial for making a phone call by voice
command operation.
● Help on Speaking
Displays useful tips of speaking for correct
command recognition by the system.
Note that the Command List feature is only
available when Alternate Command Mode is
active.
SAA2530SAA2531
Monitor, climate, audio, phone and voice recognition systems4-107