2011 INFINITI QX sensor

The FCW system will sound a warning chime
and the vehicle ahead detection indicator light
blinks to alert the driver if the vehicle is travel-
ing close to the vehicle ahead. (See “FORWARD
COLLISION WARNING (FCW) SYSTEM” in the “5.
Starting and driving” section.)
The LDW system will sound a warning chime
and blink the lane departure warning light
(orange) to alert the driver if the vehicle is
traveling close to either the left or the right of a
traveling lane with detectable lane markers.
(See “LANE DEPARTURE WARNING
(LDW)/PREVENTION (LDP) SYSTEM” in the “5.
Starting and driving” section.)
The BSW system will turn on the BSW indicator
lights, located next to the outside mirrors, if the
radar sensors detect a vehicle in the detection
zone. If the turn signal is activated in the
direction of the detected vehicle, a chime
sounds twice and the BSW indicator light will
flash. (See “BLIND SPOT WARNING (BSW) SYS-
TEM” in the “5. Starting and driving” section.)For driving or starting the vehicle on snowy
roads or slippery areas, push on the SNOW
mode switch. The SNOW mode indicator light
will illuminate. When the SNOW mode is acti-
vated, engine output is controlled to avoid
wheel spin.
Push off the SNOW mode for normal driving.
TOW MODE should be used when pulling a
heavy trailer or hauling a heavy load. Driving
the vehicle in TOW MODE with no trailer/load or
light trailer/light load will not cause any dam-
age. However, fuel economy may be reduced,
and the transmission/engine driving character-
istics may feel unusual.
SIC4454SIC4474
SNOW MODE SWITCH
TOW MODE SWITCH
Instruments and controls2-49

Power open
When the lift gate is fully closed, the lift gate
will fully open automatically by:
●pushing the power lift gate switch
Aon the
instrument panel
● pushing the lift gate opener switch
B
●pushing the power lift gate buttonCon the
Intelligent Key for more than 1 second
The hazard flashes 4 times and the outside
chime sounds when the lift gate starts opening.
NOTE:
The lift gate can be opened by the power lift gate
switch
A, the lift gate opener switchBor the
lift gate button
Ceven if the lift gate is
locked. The lift gate will individually unlock and
open.
Power close
When the lift gate is fully opened, the lift gate
will fully close automatically by:
● pushing the power lift gate switch
Aon the
instrument panel
● pushing the lift gate release button
Con
the Intelligent Key for more than 1 second
● pushing the power lift gate switch
Don the
lower part of the lift gate The hazard flashes 4 times and the outside
chime sounds when the lift gate starts closing.
NOTE:
When the lift gate is closed, it remains unlocked.
Manually lock the lift gate.
Reverse function
The power lift gate will reverse immediately if
one of the following actions is performed during
power open or power close.
●
pushing the power lift gate switch
Aon the
instrument panel
● pushing the lift gate button
Con
the Intelligent Key.
● pushing the lift gate switch
Don the lower
part of the lift gate
The outside chime sounds when the lift gate
starts to reverse.
The power lift gate button
Con the
Intelligent Key cannot be operated when the
ignition switch is in the ON position.
Auto reverse function
The auto-reverse function enables the lift gate
to automatically reverse when something is
caught in the lift gate as it is opening or closing.
When the control unit detects an obstacle, the
lift gate will reverse and return to the full open
or full close position.
If a second obstacle is detected, the lift gate
motion will stop and the drive motor will disen-
gage. The lift gate will enter the manual mode.
A pinch sensor is mounted on each side of the
lift gate. If an obstacle is detected by the pinch
sensor during power close, the lift gate will
reverse and return to the full open position
immediately.
NOTE:
If the pinch sensor is damaged or removed, the
power close function will not operate.
WARNING
There is a small distance immediately before
the closed position that cannot be detected.
Make sure that all passengers keep their
hands, etc., clear from the lift gate opening
before closing the lift gate.
Pre-driving checks and adjustments3-21

Push the “” switchBto make the inside
rearview mirror operate normally. The indicator
light will turn off. Push the “I” switch
Cto turn
the system on.
Do not allow any object to cover the sensors
D
or apply glass cleaner on them. Doing so will
reduce the sensitivity of the sensor, resulting in
improper operation.
For the HomeLink Universal Transceiver opera-
tion, see “HomeLink UNIVERSAL TRANS-
CEIVER” in the “2. Instruments and controls”
section.
OUTSIDE MIRRORS
WARNING
● Objects viewed in the outside mirror on the
passenger side are closer than they appear.
Be careful when moving to the right. Using
only this mirror could cause an accident. Use
the inside mirror or glance over your shoul-
der to properly judge distances to other
objects.
● Do not adjust the mirrors while driving. You
could lose control of your vehicle and cause
an accident.
Adjusting outside mirrors
The outside mirror control switch is located at
the lower part of the instrument panel.
The outside mirror will operate only when the
ignition switch is in the ACC or ON position.
Move the switch right
1or left2to select the
right or left side mirror, then adjust
3using
the control switch.
Defrosting outside mirrors
The outside mirrors will be heated when the
rear window defroster switch is operated. (See
“REAR WINDOW AND OUTSIDE MIRROR
DEFROSTER/WINDSHIELD DEICER SWITCH” in
the “2. Instruments and controls” section.)SPA2214
3-28Pre-driving checks and adjustments

Manual operation
Fan speed control :
Push the fan speed increase “
”orde-
crease “” buttons to manually control the
fan speed.
Push the “AUTO” button to return to automatic
control of the fan speed.
Air flow control :
Pushing the “MODE” manual air flow control
button selects the air outlet to:
: Air flows from center and side ventila- tors.
: Air flows from center and side ventila-tors and foot outlets.
: Air flows mainly from foot outlets.
: Air flows from defroster and foot outlets.
Air recirculation :
Push the intake air control button to recirculate
interior air inside the vehicle. The indicator light
on the “
” button will illuminate.
The air recirculation mode cannot be activated
when the air conditioner is in the front defrost-
ing mode “
”. Outside air circulation :
Push the intake air control button to draw
outside air into the passenger compartment.
The indicator light on the “
” button will
turn off and “” (if so equipped) will
illuminate.
Automatic intake air control :
In the AUTO mode, the intake air will be con-
trolled automatically. To manually control the
intake air, push the intake air control button.
● Without Advanced Climate Control System
(ACCS):
To return to the automatic control mode,
push the intake air control button for about
2 seconds. The indicator lights (both air
recirculation “
” and outside air circu-
lation “” buttons) will flash twice, and
then the intake air will be controlled auto-
matically.
● With Advanced Climate Control System
(ACCS):
To return to the automatic control mode,
push the intake air control button until the
indicator light on the “
” button illumi-
nates. The Advanced Climate Control System
(ACCS) turns on and the intake air will be
controlled automatically. To turn the system off :
Push the “OFF” button.
Advanced Climate Control System
(ACCS) (if so equipped)
The Advanced Climate Control System (ACCS)
keeps the air inside of the vehicle clean, using
the ion control and the automatic air intake
control with exhaust gas detecting sensor.
Monitor, climate, audio, phone and voice recognition systems4-35

Ion control :
This unit generates highly concentrated Plas-
macluster ions into the air blown from the
ventilators and reduces odor absorbed into the
interior trim.
When the air conditioner is turned on, the
system generates Plasmacluster ions automati-
cally.The amount of Plasmacluster ions increases
according to the amount of air flow. When the
air flow is high, “
” is displayed on the
screen and when the air flow is low, the indica-
tion in the screen changes to “
”.
Plasmacluster and Plasmacluster ion are regis-
tered trademarks of Sharp Corporation.
Exhaust gas/outside odor detection sensor :
This vehicle is equipped with an exhaust gas
detection sensor. When the automatic intake air
control is ON, the sensor detects industry odors
such as pulp or chemicals, and exhaust gas
such as gasoline or diesel. When such odors or
gas are detected, the system automatically
changes from the outside air circulation mode
to the recirculation mode.
When the intake air control button is pushed
under the following conditions, the indicator
light on the “
” button will illuminate and
the exhaust gas detection sensor will turn on.
● The air flow control is not in the front
defroster mode (the indicator light on the
“
” front defroster button is turned off).
● The outside temperature is about 32°F (0°C)
or more. When the automatic intake air control is ON, for
the first 5 minutes, the recirculation mode is
selected to prevent dust, dirt and pollen from
entering the vehicle and cleans the air inside of
the vehicle with positive and negative ions that
are emitted from the ventilator.
After the 5 minutes, the sensor detects exhaust
gas and automatically alternates between the
recirculation mode and outside air circulation
mode.
SAA2734
4-36Monitor, climate, audio, phone and voice recognition systems

OPERATING TIPS
When the engine coolant temperature and out-
side air temperature are low, the air flow from
the foot outlets may not operate. However, this
is not a malfunction. After the coolant tempera-
ture warms up, the air flow from the foot outlets
will operate normally.
The sensors
AandBlocated on the instru-
ment panel help maintain a constant tempera-
ture. Do not put anything on or around the
sensors.
IN-CABIN MICROFILTER
Models without Advanced Climate Control Sys-
tem:
The climate control system is equipped with an
in-cabin microfilter which collects dirt, pollen,
dust, etc. To make sure the air conditioner
heats, defogs, and ventilates efficiently, replace
the filter in accordance with the maintenance
schedule in the INFINITI Service and Mainte-
nance Guide. To replace the filter, contact an
INFINITI retailer.
The filter should be replaced if air flow is ex-
tremely decreased or when windows fog up eas-
ily when operating heater or air conditioning
system. Models with Advanced Climate Control System:
The climate control system is equipped with a
natural grape seed polyphenol filter which col-
lects and neutralizes dirt, pollen, dust, etc. To
make sure that the air conditioner heats, defogs
and ventilates efficiently, replace the filter in
accordance with the maintenance schedule in
the INFINITI Service and Maintenance Guide. To
replace the filter, contact an INFINITI retailer.
The filter should be replaced if the air flow de-
creases significantly or if windows fog up easily
when operating the heater or air conditioner.SAA3088
SAA3058
Monitor, climate, audio, phone and voice recognition systems4-39

●Replacing tires with those not originally
specified by INFINITI could affect the proper
operation of the TPMS.
● Do not inject any tire liquid or aerosol tire
sealant into the tires, as this may cause a
malfunction of the tire pressure sensors.
CAUTION
● The TPMS may not function properly when
the wheels are equipped with tire chains or
the wheels are buried in snow.
● Do not place metalized film or any metal
parts (antenna, etc.) on the windows. This
may cause poor reception of the signals from
the tire pressure sensors, and the TPMS will
not function properly.
Some devices and transmitters may temporarily
interfere with the operation of the TPMS and
cause the low tire pressure warning light to
illuminate. Some examples are:
● Facilities or electric devices using similar
radio frequencies are near the vehicle.
● If a transmitter set to similar frequencies is
being used in or near the vehicle. ●
If a computer (or similar equipment) or a
DC/AC converter is being used in or near the
vehicle.
FCC Notice:
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interfer-
ence that may cause undesired operation.
Note: Changes or modifications not expressly
approved by the party responsible for compli-
ance could void the user’s authority to operate
the equipment.
For Canada:
This device complies with RSS-210 of Industry
Canada. Operation is subject to the following
two conditions: (1) this device may not cause
interference, and (2) this device must accept any
interference, including interference that may
cause undesired operation of the device.
TPMS with Tire Inflation Indicator
When tire pressure is low, the low tire pressure
warning light illuminates.
This vehicle provides visual and audible signals
to help you inflate the tires to the recommended
COLD tire pressure.
Vehicle set-up:
1. Park the vehicle in a safe and level place.
2. Apply the parking brake and place the selector lever in the P (Park) position.
3. Place the ignition switch in the ON posi- tion. Do not start the engine.
Operation:
1. Add air to the tire.
2. In a few seconds, the hazard indicators will start flashing.
3. When the designated pressure is reached, the horn beeps once and the hazard
indicators stop flashing.
4. Perform the above steps for each tire.
● If the tire is over-inflated more than approxi-
mately 4 psi (30 kPa), the horn beeps and
the hazard indicators flash 3 times. To cor-
rect the pressure, push the core of the valve
stem on the tire briefly to release pressure.
Starting and driving5-5

●Do not place reflective materials, such as
white paper or a mirror, on the instrument
panel. The reflection of sunlight may ad-
versely affect the camera unit’s capability of
detecting the lane markers.
● Do not strike or damage the areas around
the camera unit. Do not touch the camera
lens or remove the screw located on the
camera unit. If the camera unit is damaged
due to an accident, contact an INFINITI re-
tailer. The Blind Spot Warning (BSW) system can help
alert the driver of other vehicles in adjacent
lanes when changing lanes.
The BSW system uses radar sensors
1in-
stalled near the rear bumper to detect other
vehicles beside your vehicle in an adjacent
lane.
SSD1085
BLIND SPOT WARNING (BSW) SYSTEM (if
so equipped)
Starting and driving5-29