2011 INFINITI QX warning

Locking doors and fuel-filler door
1. Move the selector lever to the P (Park)position, push the ignition switch to the
OFF position and make sure you carry the
Intelligent Key with you.*1
2. Close all the doors and the lift gate.*2
3. Push the LOCK
button1on the
Intelligent Key.
4. All the doors, the lift gate and fuel-filler door will lock.
5. The hazard indicator flashes twice and the horn chirps once.
*1: Doors will lock with the Intelligent Key while the ignition switch is in the ACC or ON
position.
*2: Doors will not lock with the Intelligent Key while any door is open.
Unlocking doors and fuel-filler door
1. Push the UNLOCKbutton2on the
Intelligent Key once.
2. The hazard indicator flashes once. The driver’s door and fuel-filler door will un-
lock.
The puddle light and the passenger cabin illu-
mination will illuminate and stay on for a short
period of time.
3. Push the UNLOCKbutton on the
Intelligent Key again within 60 seconds.
4. The hazard indicator flashes once again. All the doors will unlock.
All doors will be locked automatically unless
one of the following operations is performed
within 1 minute after pushing the UNLOCK but-
ton on the Intelligent Key while the doors are
locked. If during this 1-minute time period, the
UNLOCK button on the Intelligent Key is
pushed, all doors will be locked automatically
after another 1 minute.
●Opening any door
● Pushing the ignition switch
Opening windows
To open the windows, push the door UNLOCKbutton on the Intelligent Key for about 3
seconds after the door is unlocked.
To stop opening, release the UNLOCK
button.
Window cannot be closed using the Intelligent
Key.
The door windows can be opened or closed by
turning the mechanical key in a door lock. (See
“DOORS” earlier in this section.)
Opening/closing lift gate (if so
equipped)
1. Push the power lift gate button
3for more than 1 second.
2. The lift gate will automatically open.
The hazard indicator flashes 4 times and the
outside chime sounds for approximately 3 sec-
onds.
To close the lift gate, push the power lift gate
button
3.
The lift gate will automatically close.
If the button
3is pushed while the
lift gate is being opened or closed, the lift gate
will reverse.
The power lift gate button
3cannot
be operated when the ignition switch is in the
ON position.
Using panic alarm
If you are near your vehicle and feel threatened,
you may activate the alarm to call attention as
follows:
1. Push the PANICbutton4on the
Intelligent Key for more than 1 second.
2. The theft warning alarm and headlights will stay on for 25 seconds.
3-16Pre-driving checks and adjustments

Switching procedure :
Push the LOCK
1and UNLOCK2
buttons on the Intelligent Key simultaneously
for more than 2 seconds to switch the mode
from one to the other.
When pushing the buttons to set the hazard
indicator mode, the hazard indicator flashes 3
times.
When pushing the buttons to set the hazard
indicator and horn mode, the hazard indicator
flashes once and the horn chirps once.
1. Pull the hood lock release handle1
located below the instrument panel; the
hood will then spring up slightly.
2. Pull the lever
2up at the front of the
hood with your fingertips and raise the
hood.
3. When closing the hood, slowly close the hood down and make sure it locks into
place.
WARNING
●Make sure the hood is completely closed and
latched before driving. Failure to do so could
cause the hood to fly open and result in an
accident.
● If you see steam or smoke coming from the
engine compartment, to avoid injury do not
open the hood.
SPA2775
HOOD
3-18Pre-driving checks and adjustments

WARNING
●Always be sure the lift gate has been closed
securely to prevent it from opening while
driving.
● Do not drive with the lift gate open. This
could allow dangerous exhaust gases to be
drawn into the vehicle. See “EXHAUST GAS
(carbon monoxide)” in the “5. Starting and
driving” section of this manual.
● Do not leave children unattended inside the
vehicle. They could unknowingly activate
switches or controls. Unattended children
could become involved in serious accidents.
● Always be sure that hands and feet are clear
of the door frame to avoid injury while clos-
ing the lift gate.
OPERATING MANUAL LIFT GATE
To open the lift gate, unlock it and push the lift
gate opener switch
A. Pull up the lift gate to
open.
The lift gate can be unlocked by:
● pushing the unlock button
on the
Intelligent Key twice.
● pushing the lift gate request switch with the
Intelligent Key carried on you. ●
pushing the door handle request switch
twice with the Intelligent Key carried on you.
● pushing the power door lock switch to the
unlock position.
● inserting the mechanical key into the driv-
er’s door key cylinder and turning it to the
rear of the vehicle twice.
To close the lift gate, pull down until it securely
locks.
OPERATING POWER LIFT GATE
To operate the power lift gate, the selector lever
must be in the P (Park) position.
The power lift gate will not operate if the battery
voltage is low.SPA2774
LIFT GATE
Pre-driving checks and adjustments3-19

Power open
When the lift gate is fully closed, the lift gate
will fully open automatically by:
●pushing the power lift gate switch
Aon the
instrument panel
● pushing the lift gate opener switch
B
●pushing the power lift gate buttonCon the
Intelligent Key for more than 1 second
The hazard flashes 4 times and the outside
chime sounds when the lift gate starts opening.
NOTE:
The lift gate can be opened by the power lift gate
switch
A, the lift gate opener switchBor the
lift gate button
Ceven if the lift gate is
locked. The lift gate will individually unlock and
open.
Power close
When the lift gate is fully opened, the lift gate
will fully close automatically by:
● pushing the power lift gate switch
Aon the
instrument panel
● pushing the lift gate release button
Con
the Intelligent Key for more than 1 second
● pushing the power lift gate switch
Don the
lower part of the lift gate The hazard flashes 4 times and the outside
chime sounds when the lift gate starts closing.
NOTE:
When the lift gate is closed, it remains unlocked.
Manually lock the lift gate.
Reverse function
The power lift gate will reverse immediately if
one of the following actions is performed during
power open or power close.
●
pushing the power lift gate switch
Aon the
instrument panel
● pushing the lift gate button
Con
the Intelligent Key.
● pushing the lift gate switch
Don the lower
part of the lift gate
The outside chime sounds when the lift gate
starts to reverse.
The power lift gate button
Con the
Intelligent Key cannot be operated when the
ignition switch is in the ON position.
Auto reverse function
The auto-reverse function enables the lift gate
to automatically reverse when something is
caught in the lift gate as it is opening or closing.
When the control unit detects an obstacle, the
lift gate will reverse and return to the full open
or full close position.
If a second obstacle is detected, the lift gate
motion will stop and the drive motor will disen-
gage. The lift gate will enter the manual mode.
A pinch sensor is mounted on each side of the
lift gate. If an obstacle is detected by the pinch
sensor during power close, the lift gate will
reverse and return to the full open position
immediately.
NOTE:
If the pinch sensor is damaged or removed, the
power close function will not operate.
WARNING
There is a small distance immediately before
the closed position that cannot be detected.
Make sure that all passengers keep their
hands, etc., clear from the lift gate opening
before closing the lift gate.
Pre-driving checks and adjustments3-21

●Push the power door lock switch to the
UNLOCK position.
To lock, close the fuel-filler door securely and
lock all doors by operating the door handle
request switch, the LOCK button on the Intelli-
gent Key, the mechanical key or the power door
lock switch.
FUEL-FILLER CAP
WARNING
● Gasoline is extremely flammable and highly
explosive under certain conditions. You
could be burned or seriously injured if it is
misused or mishandled. Always stop engine
and do not smoke or allow open flames or
sparks near the vehicle when refueling.
● Do not attempt to top off the fuel tank after
the fuel pump nozzle shuts off automati-
cally. Continued refueling may cause fuel
overflow, resulting in fuel spray and possi-
bly a fire. ●
Use only an original equipment type fuel-
filler cap as a replacement. It has a built-in
safety valve needed for proper operation of
the fuel system and emission control sys-
tem. An incorrect cap can result in a serious
malfunction and possible injury. It could
also cause the malfunction indicator light to
come on.
● Never pour fuel into the throttle body to at-
tempt to start your vehicle.
● Do not fill a portable fuel container in the
vehicle or trailer. Static electricity can cause
an explosion of flammable liquid, vapor or
gas in any vehicle or trailer. To reduce the
risk of serious injury or death when filling
portable fuel containers:
– Always place the container on the ground when filling.
– Do not use electronic devices when filling.
– Keep the pump nozzle in contact with the container while you are filling it.
– Use only approved portable fuel contain- ers for flammable liquid.
CAUTION
●If fuel is spilled on the vehicle body, flush it
away with water to avoid paint damage.
● Insert the cap straight into the fuel-filler
tube, then tighten until the fuel-filler cap
clicks. Failure to tighten the fuel-filler cap
properly may cause the
malfunction
indicator light (MIL) to illuminate. If the
light illuminates because the fuel-
filler cap is loose or missing, tighten or in-
stall the cap and continue to drive the ve-
hicle. The
light should turn off after a
few driving trips. If thelight does not
turn off after a few driving trips, have the
vehicle inspected by an INFINITI retailer.
●
The LOOSE FUEL CAP warning (if so equipped)
will appear if the fuel-filler cap is not properly
tightened. It may take a few driving trips for
the message to be displayed. Failure to
tighten the fuel-filler cap properly after the
LOOSE FUEL CAP warning (if so equipped) ap-
pears may cause the
Malfunction Indi-
cator Light (MIL) to illuminate.
The fuel-filler cap is a ratcheting type. Turn the
cap counterclockwise to remove. To tighten,
turn the cap clockwise until ratcheting clicks
are heard.
3-24Pre-driving checks and adjustments

To remove the fuel-filler cap:
1. Turn the fuel-filler cap counterclockwise toremove.
2. Put the fuel-filler cap on the cap holder
A
while refueling.
To install the fuel-filler cap:
1. Insert the fuel-filler cap straight into the fuel-filler tube.
2. Turn the fuel-filler cap clockwise until a single click is heard.
LOOSE FUEL CAP warning (if so
equipped)
The LOOSE FUEL CAP warning appears on the
dot matrix liquid crystal display when the fuel-
filler cap is not tightened correctly after the
vehicle has been refueled. It may take a few
driving trips for the warning to be displayed.
To turn off the warning, perform the following:
1. Remove and install the fuel-filler cap as
soon as possible. (See “FUEL-FILLER CAP”
earlier in this section.)
2. Tighten the fuel-filler cap until it clicks. 3. Push the
switchAon the right
side of the combination meter panel for
longer than 1 second to turn off the LOOSE
FUEL CAP warning after tightening the fuel
cap.
SPA2753SPA2815
Pre-driving checks and adjustments3-25

WARNING
●Do not adjust the steering wheel while driv-
ing. You could lose control of your vehicle
and cause an accident.
● Do not adjust the steering wheel any closer
to you than is necessary for proper steering
operation and comfort. The driver’s air bag
inflates with great force. If you are unre-
strained, leaning forward, sitting sideways
or out of position in any way, you are at
greater risk of injury or death in a crash. You
may also receive serious or fatal injuries
from the air bag if you are up against it when
it inflates. Always sit back against the seat-
back and as far away as practical from the
steering wheel. Always use the seat belts.
ELECTRIC OPERATION
Tilt or telescopic operation
Move the lever1to adjust the steering wheel
up or down, forward or rearward to the desired
position.
Entry/Exit function operation :
The automatic drive positioner system will
make the steering wheel move up automatically
when the driver’s door is opened with the
ignition switch in the LOCK position. This lets
the driver get into and out of the seat more
easily.
For more information, see “AUTOMATIC DRIVE
POSITIONER” later in this section.
SPA2754
SIC3451
TILT/TELESCOPIC STEERING SUN VISORS
3-26Pre-driving checks and adjustments

Push the “” switchBto make the inside
rearview mirror operate normally. The indicator
light will turn off. Push the “I” switch
Cto turn
the system on.
Do not allow any object to cover the sensors
D
or apply glass cleaner on them. Doing so will
reduce the sensitivity of the sensor, resulting in
improper operation.
For the HomeLink Universal Transceiver opera-
tion, see “HomeLink UNIVERSAL TRANS-
CEIVER” in the “2. Instruments and controls”
section.
OUTSIDE MIRRORS
WARNING
● Objects viewed in the outside mirror on the
passenger side are closer than they appear.
Be careful when moving to the right. Using
only this mirror could cause an accident. Use
the inside mirror or glance over your shoul-
der to properly judge distances to other
objects.
● Do not adjust the mirrors while driving. You
could lose control of your vehicle and cause
an accident.
Adjusting outside mirrors
The outside mirror control switch is located at
the lower part of the instrument panel.
The outside mirror will operate only when the
ignition switch is in the ACC or ON position.
Move the switch right
1or left2to select the
right or left side mirror, then adjust
3using
the control switch.
Defrosting outside mirrors
The outside mirrors will be heated when the
rear window defroster switch is operated. (See
“REAR WINDOW AND OUTSIDE MIRROR
DEFROSTER/WINDSHIELD DEICER SWITCH” in
the “2. Instruments and controls” section.)SPA2214
3-28Pre-driving checks and adjustments