2011 INFINITI M mirror

The Lane Departure Warning (LDW)
system/Lane Departure Prevention (LDP) sys-
tem will operate when the vehicle is driven at
speeds of approximately 45 MPH (70 km/h) and
above, and when it is traveling close to either
the left or the right of a traveling lane.
Each system functions as follows:
●Lane Departure Warning (LDW) system —
warns the driver by a warning light and
chime.
● Lane Departure Prevention (LDP) system —
warns the driver by a warning light and
chime, and helps assist the driver to return
the vehicle to the center direction of the
traveling lane by applying brake control to
the left or right wheels individually (for a
short period of time). The LDW and LDP systems monitor the lane
markers on the traveling lane using the camera
unit
1located above the inside mirror. When
the camera unit detects that the vehicle is
traveling close to either the left or the right of
the traveling lane, the lane departure warning
light
2on the instrument panel blinks in
orange and a warning chime sounds. When the
LDP system is on, it will automatically apply the
brakes for a short period of time, using the
function of the Vehicle Dynamic Control (VDC)
system.
To turn on the LDW system, push the warning
systems switch
3. The warning systems ON
indicator light
4on the switch will illuminate.
To turn on the LDP system, push the dynamic
driver assistance switch
5. The LDP ON indi-
cator light
2will illuminate in green.
SSD0937
SSD0975
LANE DEPARTURE WARNING (LDW)
SYSTEM/LANE DEPARTURE PREVENTION
(LDP) SYSTEM (if so equipped)
5-20Starting and driving
—
—
07/15/10—tbrooks


Action to take:
When the above conditions no longer exist, turn
off the LDP system. Push the dynamic driver
assistance switch again to turn the LDP system
back on.
Temporary disabled status at high temperature :
If the vehicle is parked in direct sunlight under
high temperature conditions (over approxi-
mately 104°F (40°C)) and then the LDP system is
turned on, the LDP system may be deactivated
automatically. The lane departure warning light
(orange) will blink.
Action to take:
When the above conditions no longer exist, turn
off the LDP system. Push the dynamic driver
assistance switch again to turn the LDP system
back on.
LANE CAMERA UNIT MAINTENANCE
The lane camera unit1for the LDW/LDP
system is located above the inside mirror. To
keep the proper operation of the LDW/LDP
systems and prevent a system malfunction, be
sure to observe the following:
● Always keep the windshield clean.
● Do not attach a sticker (including transpar-
ent material) or install an accessory near the
camera unit.
● Do not place reflective materials, such as
white paper or a mirror, on the instrument
panel. The reflection of sunlight may ad-
versely affect the camera unit’s capability of
detecting the lane markers. ●
Do not strike or damage the areas around
the camera unit. Do not touch the camera
lens or remove the screw located on the
camera unit. If the camera unit is damaged
due to an accident, contact an INFINITI re-
tailer.
SSD0453
Starting and driving5-27
—
—
01/12/10—pattie


The BSW and BSI systems can help alert the
driver of other vehicles in adjacent lanes when
changing lanes.The BSW system uses radar sensors
1in-
stalled near the rear bumper to detect other
vehicles beside your vehicle in an adjacent
lane. In addition to the radar sensors, the BSI
system uses a camera
2installed behind the
windshield to monitor the lane markers of your
traveling lane. The radar sensors can detect vehicles on either
side of your vehicle within the detection zone
shown as illustrated. This detection zone starts
from the outside mirror of your vehicle and
extends approximately 10 ft (3.0 m) behind the
rear bumper, and approximately 10 ft (3.0 m)
sideways.
The BSW system operates above approximately
20 MPH (32 km/h). If the radar sensors
detect
a vehicle in the detection zone, the BSW/BSI
indicator light illuminates. If the driver then
activates the turn signal, a chime will sound
twice and the BSW/BSI indicator light will flash.
SSD1027
Detection zone
SSD1030
BLIND SPOT WARNING (BSW) SYSTEM/
BLIND SPOT INTERVENTION™ (BSI)
SYSTEM (if so equipped)
5-28Starting and driving
—
—
03/02/10—pattie


The BSI system operates above approximately
37 MPH (60 km/h). If the system detects a
vehicle in the detection zone and your vehicle is
approaching the lane marker, the BSI system
issues an audible warning (three times), flashes
the BSW/BSI indicator light and slightly applies
the brakes for a short period of time on one side
to help return the vehicle back to the traveling
lane. Whenever the BSI system is turned on, the
BSW system will also be on.
WARNING
●The BSW and BSI systems are not a replace-
ment for proper driving procedure and is not
designed to prevent contact with vehicles or
objects. When changing lanes, always use
the side and rear mirrors and turn and look in
the direction you will move to ensure it is
safe to change lanes. Never rely solely on the
BSW or BSI system.
● Using the BSI system under some road, lane
marker or weather conditions could lead to
improper system operation. Always rely on
your own steering and braking operation to
avoid accidents.
● The BSW and BSI systems may not provide a
warning or brake control for vehicles that
pass through the detection zone quickly.
BSW SYSTEM OPERATION
If the radar sensors detect a vehicle in the
detection zone, the BSW/BSI indicator light
next to the outside mirror will illuminate in the
direction of the detected vehicle. If the turn
signal is then activated, the BSW/BSI indicator
light flashes and a chime sounds twice. The
indicator light continues to flash until the de-
tected vehicle leaves the detection zone.
The BSW/BSI indicator lights illuminate for a
few seconds when the ignition switch is pushed
to the ON position.
BSW/BSI indicator light
SSD1028
BSW/BSI system warning light
SSD1029
Warning systems switch
SIC4335
Starting and driving5-29
—
—
03/02/10—pattie


●The radar sensors detection zone is de-
signed based on a standard lane width.
When driving in a wider lane, the radar
sensors may not detect vehicles in an adja-
cent lane. When driving in a narrow lane, the
radar sensors may detect vehicles driving
two lanes away.
● The radar sensors are designed to ignore
most stationary objects, however objects
such as guardrails, walls, foliage and parked
vehicles may occasionally be detected. This
is a normal operating condition.
● The camera may not detect lane markers in
the following situations and the BSI system
may not operate properly.
– On roads where there are multiple paral- lel lane markers; lane markers that are
faded or not painted clearly; yellow
painted lane markers; non-standard lane
markers; lane markers covered with wa-
ter, dirt, snow, etc.
– On roads where discontinued lane mark- ers are still detectable.
– On roads where there are sharp curves.
– On roads where there are sharply con- trasting objects, such as shadows, snow,
water, wheel ruts, seams or lines remain-
ing after road repairs. – On roads where the traveling lane merges
or separates.
– When the vehicle’s traveling direction does not align with the lane markers.
– When traveling close to the vehicle in front of you, which obstructs the lane
camera unit detection range.
– When rain, snow or dirt adheres to the windshield in front of a lane camera unit.
– When the headlights are not bright due to dirt on the lens or if aiming is not ad-
justed properly.
– When strong light enters a lane camera unit. (e.g. light directly shines on the front
of the vehicle at sunrise or sunset.)
– When a sudden change in brightness occurs. (e.g. when the vehicle enters or
exits a tunnel or under a bridge.)
BSW/BSI DRIVING SITUATIONS
Another vehicle approaching from
behind
The BSW/BSI indicator light illuminates if a
vehicle enters the detection zone from behind
in an adjacent lane.
However, if the overtaking vehicle is traveling
much faster than your vehicle, the indicator
light may not illuminate before the detected
vehicle is beside your vehicle. Always use the
side and rear mirrors and turn and look in the
direction your vehicle will move to ensure it is
safe to change lanes.
SSD1026
Starting and driving5-33
—
—
01/13/10—tbrooks


SYSTEM MAINTENANCE
●The two radar sensor units1for the BSW
and BSI systems are located near the rear
bumper. Always keep the area near the radar
sensors clean. Do not attach stickers (includ-
ing transparent material), install accessories
or apply additional paint near the radar
sensors. Do not strike or damage the area
around the radar sensors. Consult an
INFINITI retailer if the area around the radar
sensors is damaged due to a collision.
● The BSI system uses the same camera
2
that is used by the LDW/LDP system located
in front of the inside mirror. For maintenance of the camera, see “LANE
DEPARTURE WARNING (LDW) SYSTEM/LANE DE-
PARTURE PREVENTION (LDP) SYSTEM” earlier in
this section.
Radio frequency statement
This device complies with part 15 of the FCC
Rules and RSS-310 of Industry Canada.
Operation is subject to the following two con-
ditions:
1. This device may not cause harmful inter-
ference.
2. This device must accept any interference received, including interference that may
cause undesired operation.
Frequency of operation: 24.05GHz — 24.25GHz
Field Strength: Not greater than 2.5V/m peak
(0.25V/m average) at a distance of 3 m
The manufacturer is not responsible for any
radio or TV interference caused by unauthorized
modifications to this equipment. Such modifi-
cations could void the user’s authority to oper-
ate the equipment.
PRECAUTIONS ON CRUISE CONTROL
●If the cruise control system malfunctions, it
will cancel automatically. The SET indicator
on the dot matrix crystal display will then
blink to warn the driver.
● If the engine coolant temperature becomes
excessively high, the cruise control system
will be canceled automatically.
● If the SET indicator blinks, turn the cruise
control main switch off and have the system
checked by your INFINITI retailer.
● The SET indicator may sometimes blink
when the cruise control main switch is
turned ON while pushing the
RESUME/ACCELERATE, SET/COAST or CAN-
CEL switch. To properly set the cruise control
system, perform the steps below in the order
indicated.
WARNING
Do not use the cruise control when driving un-
der the following conditions:
● when it is not possible to keep the vehicle at
a set speed
● in heavy traffic or in traffic that varies in
speed
● on winding or hilly roads
SSD1027
CRUISE CONTROL
Starting and driving5-39
—
—
01/12/10—pattie


HEADLIGHTS
Replacing
Xenon headlight bulb :
WARNING
HIGH VOLTAGE
When xenon headlights are on, they produce a
high voltage. To prevent an electric shock,
never attempt to modify or disassemble. Al-
ways have your xenon headlights replaced at
an INFINITI retailer. For additional information,
see “HEADLIGHT AND TURN SIGNAL SWITCH” in
the “2. Instruments and controls” section.
Use the same number and wattage shown in the
following chart as originally installed.
If replacement is required, see an INFINITI re-
tailer.
Fog may temporarily form inside the lens of the
exterior lights in the rain or in a car wash. A
temperature difference between the inside and
the outside of the lens causes the fog. This is
not a malfunction. If large drops of water collect
inside the lens, contact an INFINITI retailer.
EXTERIOR AND INTERIOR LIGHTS
Item Wattage (W)Bulb No.
Headlight* High/Low beams (xenon) 35D2S
Front turn signal light* 21WY21W
Front fog light* 35H8
Park light and front side marker light* 5W5W
Rear combination light* back-up 16W16W
turn signal 21WY21W
stop/tail/side marker LED—
License plate light* 5W5W
Map light 8—
Rear personal light 8—
Vanity mirror light 2—
Step light* 5—
Trunk light* 3.4—
Courtesy light LED—
High-mounted stop light* LED—
*: See an INFINITI retailer for replacement.
NOTE: Always check with the Parts Department at an INFINITI retailer for the latest information about
parts.
8-28Maintenance and do-it-yourself
—
—
07/26/10—dmoore


If you have a flat tire, see “FLAT TIRE” in the “6. In
case of emergency” section.
TIRE PRESSURE
Tire Pressure Monitoring System
(TPMS)
This vehicle is equipped with the Tire Pressure
Monitoring System (TPMS). It monitors tire pres-
sure of all tires except the spare. When the low
tire pressure warning light is lit and the CHECK
TIRE PRESSURE warning (if so equipped) appears
in the dot matrix liquid crystal display, one or
more of your tires is significantly under-inflated.
The TPMS will activate only when the vehicle is
driven at speeds above 16 MPH (25 km/h). Also,
this system may not detect a sudden drop in tire
pressure (for example a flat tire while driving).
For more details, see “Low tire pressure warning
light” in the “2. Instruments and controls” sec-
tion, “TIRE PRESSURE MONITORING SYSTEM
(TPMS)” in the “5. Starting and driving” section
and “TIRE PRESSURE MONITORING SYSTEM
(TPMS)” in the “6. In case of emergency” section.
Tire inflation pressure
Check the pressure of the tires (includ-
ing the spare) often and always prior to
long distance trips. The recommendedtire pressure specifications are shown
on the Tire and Loading Information
label under the “Cold Tire Pressure”
heading. The Tire and Loading Informa-
tion label is affixed to the driver side
center pillar. Tire pressures should be
checked regularly because:
●Most tires naturally lose air over time.
●Tires can lose air suddenly when
driven over potholes or other objects
or if the vehicle strikes a curb while
parking.
The tire pressures should be checked
when the tires are cold. The tires are
considered COLD after the vehicle has
been parked for 3 or more hours, or
driven less than 1 mile (1.6 km) at mod-
erate speeds.
Incorrect tire pressure, including under
inflation, may adversely affect tire life
and vehicle handling.
Vanity mirror light
SDI1839
WHEELS AND TIRES
8-30Maintenance and do-it-yourself
—
—
07/26/10—dmoore