2011 INFINITI EX display

Front-side view
Guiding lines:
Guiding lines that indicate the width and the
front end of the vehicle are displayed on the
monitor.
The front-of-vehicle line
1shows the front part
of the vehicle.
The side-of-vehicle line
2shows the vehicle
width including the outside mirror.
The extensions
3of both the front1and side
2lines are shown with a green dotted line. The corner sonar indicator
4will appear when
a corner of the vehicle moves closer to an
object.
The corner sonar indicator
4can be turned off.
See “AROUND VIEW MONITOR SETTINGS” later
in this section.
CAUTION
The turn signal light may overlap with the side-
of-vehicle line. This is not a malfunction.
Infrared illumination:
The images on the front-side view can be dis-
played at night using the infrared illumination
on the outside mirror.
Rear-wide view
The rear-wide view shows a wider area on the
entire screen and allows the checking of the
blind corners on the right and left sides. The
rear-wide view displays an approximately 180-
degree area while the front view and the rear-
view display an approximately 150-degree area.
The predicted course lines are not displayed on
the rear-wide view.
Distance guide lines:
Indicates distances from the vehicle body.
● Red line
1: approx. 1.5 ft (0.5 m)
● Yellow line
2: approx. 3 ft (1 m)
● Green line
3: approx. 7 ft (2 m)
● Green line
4: approx. 10 ft (3 m)
SAA1842SAA2629
Monitor, climate, audio, phone and voice recognition systems4-33

Vehicle width guide lines5:
Indicates the vehicle width when backing up.
The corner sonar indicator
6will appear when
a corner of the vehicle moves closer to an
object.
DIFFERENCE BETWEEN PREDICTED AND
ACTUAL DISTANCES
The distance guide line and the vehicle width
guide line on the front and the rearview should
be used as a reference only when the vehicle is
on a level, paved surface. The distance viewed
on the monitor is for reference only and may be
different than the actual distance between the
vehicle and displayed objects.
Moving to a steep uphill
When moving the vehicle up a hill, the distance
guide lines and the vehicle width guide lines
are shown closer than the actual distance. For
example, the display shows 3 ft (1.0 m) to the place
A, but the actual 3 ft (1.0 m) distance on
the hill is the place
B. Note that any object on
the hill is viewed in the monitor further than it
appears.
SAA1978
4-34Monitor, climate, audio, phone and voice recognition systems

Moving to a steep downhill
When moving the vehicle down a hill, the
distance guide lines and the vehicle width
guide lines are shown further than the actual
distance. For example, the display shows 3 ft(1.0 m) to the place
A, but the actual 3 ft
(1.0 m) distance on the hill is the place
B. Note
that any object on the hill is viewed in the
monitor closer than it appears.
Moving near a projecting object
The predicted course linesAdo not touch the
object in the display. However, the vehicle may
hit the object if it projects over the actual
moving course.
SAA1979SAA1923
Monitor, climate, audio, phone and voice recognition systems4-35

Moving closer to a projecting object
The positionCis shown further than the
position
Bin the display. However, the posi-
tion
Cis actually at the same distance as the
position
A. The vehicle may hit the object when moving toward the position
Aif the
object projects over the actual moving course.
CAMERA AIDING CORNER SONAR
FUNCTION
When the corner of the vehicle moves closer to
the object while the Around View Monitor is
displayed, an indicator is displayed and a tone
is sounded by the corner sonar function to warn
the driver.
The color of the corner sonar indicator and the
pattern of the tone vary according to the dis-
tance to the object.
When the object is detected, the indicator
(green) appears and blinks and the tone sounds
intermittently. When the vehicle moves closer to
the object, the color of the indicator turns
yellow and the rate of the blinking and the
volume of the tone increase. When the corner of
the vehicle is very close to the object, the
indicator stops blinking and turns red, and the
tone sounds continuously.
Keep the corner sonars (located on the front
and rear bumper fascia) free from snow, ice and
large accumulations of dirt. Do not clean the
sensors with sharp objects. If the sensors are
covered, the accuracy of the corner sonar func-
tion will be diminished.
WARNING
● The corner sonar function is not designed to
prevent the object.
● The colors of the corner sonar indicator and
the distance guide lines in the
front/rearview indicate different distances
to the object.
● Inclement weather may affect the function of
the corner sonar system; this may include
reduced performance or a false activation.
● This function is designed as an aid to the
driver in detecting large stationary objects
to help avoid damaging the vehicle. The sys-
tem will not detect small objects below the
bumper, and may not detect objects close to
the bumper or on the ground.
● If your vehicle sustains damage to the bum-
per fascia, leaving it misaligned or bent, the
sensing zone may be altered causing inaccu-
rate measurement of obstacles or false
alarms.
CAUTION
Keep the interior of the vehicle as quiet as pos-
sible to hear the tone clearly.
SAA1980
4-36Monitor, climate, audio, phone and voice recognition systems

HOW TO ADJUST THE SCREEN VIEW
To adjust the Display ON/OFF, Brightness, Tint,
Color, Contrast and Black Level of the Around
View Monitor, push theSETTINGbutton with the
Around View Monitor on, select the item key
and adjust the level using the INFINITI control-
ler.
Do not adjust the Brightness, Tint, Color, Con-
trast and Black Level of the Around View Moni-
tor while the vehicle is moving. Make sure the
parking brake is firmly applied.
AROUND VIEW MONITOR SETTINGS
To set up the Around View Monitor to your pre-
ferred settings, push the SETTINGbutton, select
the “Camera” key and push the ENTERbutton.
Predictive Course Lines:
When this item is turned on, the predictive course
line is displayed in the front and the rearview.
Camera View Priority:
The view shown on the screen at the beginning
of around view monitor operation can be se-
lected in order of priority.
Color/Brightness Combination (models without
navigation system):
When this item is turned on, color and bright-
ness of the displayed screen is adjusted.
Non-viewable Area Reminder (models with
navigation)/Blind-Area Reminder (models with-
out navigation):
When this item is turned on, the non-viewable
area is highlighted in yellow for 7 seconds after
the bird-eye view is displayed.
Sonar Beep:
When this item is turned on, you will hear a tone
sound when the corner sonar indicator appears.
Models with navigation system
SAA3649
Models without navigation system
SAA3328
Monitor, climate, audio, phone and voice recognition systems4-37

Sonar Display:
When this item is turned on, the corner sonar
indicator is displayed in the front-side view.
Corner Sensor Sensitivity:
Adjust the sensitivity level of the corner sonar
higher (right) or lower (left).
OPERATING TIPS
●The screen displayed on the Around View
Monitor will automatically return to the pre-
vious screen 3 minutes after the CAMERA
button has been pushed while the shift lever
is in a position other than the R (Reverse)
position.
● The display of images on the screen may be
delayed after screens are switched. Objects
in the Around View Monitor may be distorted
momentarily until the Around View Monitor
screen is displayed completely.
● When the temperature is extremely high or
low, the screen may not display objects
clearly. This is not a malfunction.
● When strong light directly shines on the
camera, objects may not be displayed
clearly. This is not a malfunction.
● The screen may flicker under fluorescent
light. This is not a malfunction. ●
The colors of objects on the Around View
Monitor may differ somewhat from those of
the actual object.
● Objects on the monitor may not be clear and
the color of the object may differ in a dark
location or at night. This is not a malfunc-
tion.
● There may be differences in clearness be-
tween each camera view of the bird-eye
view.
● If dirt, rain or snow attaches to the camera,
the Around View Monitor may not display
objects clearly. Clean the camera.
● Do not use alcohol, benzine or thinner to
clean the camera. This will cause discolor-
ation. To clean the camera, wipe with a cloth
that has been dampened with a diluted mild
cleaning agent and then wipe with a dry
cloth.
● Do not damage the camera because the
monitor screen may be adversely affected.
● Do not use wax on the camera window. Wipe
off any wax with a clean cloth that has been
dampened with a mild detergent diluted
with water.
Center ventilators
SAA1981
Side ventilators
SAA1982
VENTILATORS
4-38Monitor, climate, audio, phone and voice recognition systems

side temperature, air flow distribution and fan
speed after the preferred temperature is set
manually.
1. Push the “AUTO” button on. (The indicatoron the button will illuminate and AUTO will
be displayed.)
2. Turn the temperature control dial (driver side) to set the desired temperature.
●The temperature can be set within the
following range.
– For U.S.: 60 to 90°F
– For Canada: 18 to 32°C
● The temperature of the passenger com-
partment will be maintained automati-
cally. Air flow distribution and fan speed
will also be controlled automatically.
3. You can individually set driver and front passenger side temperature using each
temperature control button. When the
“DUAL” button is pushed or the passen-
ger side temperature control button is
turned, the DUAL indicator will come on.
To turn off the passenger side tempera-
ture control, push the “DUAL” button.
4. To turn off the climate control system, push the “OFF” button.
A visible mist may be seen coming from the
ventilators in hot, humid conditions as the air is
cooled rapidly. This does not indicate a mal-
function.
Heating (A/C OFF) :
The air conditioner does not activate in this
mode. When you need to heat only, use this
mode.
1. Push the “AUTO” button on.
2. Push the “A/C” button. (The A/C indicatorwill turn off.)
3. Turn the temperature control dial to set the desired temperature.
●The temperature of the passenger compart-
ment will be maintained automatically. Air
flow distribution and fan speed are also
controlled automatically.
● Do not set the temperature lower than the
outside air temperature. Otherwise the sys-
tem may not work properly.
● Not recommended if windows fog up.
Dehumidified defrosting or defogging:
1. Push the “” front defroster button.
(The indicator light on the button will
come on.)
2. Turn the temperature control dial to set the desired temperature.
●To quickly remove ice from the outside of the
windows, push the fan speed increase but-
ton “
” and set it to the maximum
position.
● As soon as possible after the windshield is
clean, push the “AUTO” button to return to
the auto mode.
● When the “
” front defroster button is
pushed, the air conditioner will automati-
cally be turned on at outside temperatures
above 23°F (5°C) to defog the windshield,
and the air recirculate mode will automati-
cally be turned off.
Outside air is drawn into the passenger
compartment to improve the defogging per-
formance.
Manual operation
Fan speed control :
Push the fan speed increase “
”orde-
crease “” buttons to manually control the
fan speed.
Push the “AUTO” button to return to automatic
control of the fan speed.
Monitor, climate, audio, phone and voice recognition systems4-41

1. “AUTO” automatic operationbutton/Temperature control dial (driver
side)*
2. “A/C” air conditioner ON/OFF button*
3. “
” fan speed increase button
4. “” front defroster button
5. “MODE” manual air flow control button*
6. “DUAL” zone control ON/OFF button/Temperature control dial (passen-
ger side)*
7. “OFF” button for climate control system*
8. “
” fan speed decrease button 9. “
” rear window defogger button
(See “REAR WINDOW AND OUTSIDE MIR-
ROR DEFROSTER SWITCH” in the “2. In-
struments and controls” section.)
10. “
” auto-recirculation
button/intake air control button
AUTOMATIC CLIMATE CONTROL
(Type B)
Automatic operation (AUTO)
The AUTO mode may be used year-round as the
system automatically controls constant tem- perature, air flow distribution and fan speed
after the desired temperature is set manually.
To turn off the heater and air conditioner, push
the “OFF” button.
Cooling and dehumidified heating:
1. Push the “AUTO” button.
(The AUTO indicator light will illuminate
and “AUTO” will appear on the display.)
2. If the A/C indicator light does not illumi- nate, push the “A/C” button.
(The A/C indicator light will illuminate.)
3. Turn the temperature control dial (driver’s side) to set the desired temperature.
●The temperature can be set within the
following range.
– For U.S.: 60 to 90°F
– For Canada: 18 to 32°C
● When the DUAL indicator light is turned
off:
– Pushing the driver’s side “AUTO” but- ton changes both the driver’s and
front passenger’s side temperature.
– Pushing the passenger’s side “DUAL” button changes only the front passen-
ger’s side temperature. (The DUAL in-
dicator light will illuminate and
“DUAL” will appear on the display.)Type B
SAA3568
Monitor, climate, audio, phone and voice recognition systems4-43