2011 HONDA ACCORD Owners Manual

Store a driver’s seat position only
when the vehicle is parked.Turn the ignition switch to the ON
(II) position. You cannot add a
new seat position in memory
unless the ignition switch is in the
ON (II) position. You can recall a
memorized position with the
ignition switch in any position.
Adjust the seat to a comfortable
position (see page ).
Your vehicle has a memory feature
f or the driver’s seat position.
Two seat positions can be stored in
separate memories. You select a
memorized position by pushing the
appropriate button or using the
appropriate remote transmitter
(Driver 1 or Driver 2).
Press and release the SET button.
You will hear a beep. Immediately
press and hold one of the memory
buttons (1 or 2) until you hear two
beeps. The indicator in the
memory button will come on. The
current position of the driver’s
seat is now stored.
1. 2.
3.
92
CONT INUED
U.S. EX-L V6, and Canadian EX-L and
EX-L V6 with navigation systemStoring a Driving Position in
Memory
Driving Position Memory System
Inst rument s and Cont rols
101
MEMORY BUTTONS
SET BUTTON
Main Menu

To select a memorized position, do
this:
Each memory button stores only one
driving position. Storing a new
position erases the previous setting
stored in that button’s memory. If
you want to add a new position while
retaining the current one, use the
other memory button.
All stored driving positions will be
lost if your vehicle’s battery goes
dead or is disconnected.
To cancel the storing procedure
af ter pressing the SET button, do
any of the f ollowing:
Press the SET button again within
5 seconds.
Fail to press a memory button
within 5 seconds.
Readjust the seat position.
Make sure the parking brake is set
and the shif t lever is in Park
(automatic).
Press the desired memory button
(1 or 2) until you hear a beep, then
release the button.
1. 2.
Selecting a Memorized Position
Driving Position Memory System
102
MEMORY BUTTONS
Main Menu

To stop the system’s automatic
adjustment, do any of these actions:Push any of the adjustment
switches f or the seat.
The system will move the driver’s
seat to the memorized position. The
indicator in the selected memory
button will f lash during movement.
When the adjustment is complete,
you will hear two beeps, and the
indicator will stay on.
Press any button on the driver’s
door: SET, memory button 1 or 2.
If the parking brake is not set, you
must press and hold the memory
button until the adjustment is
complete. Release the parking brake
(manual).
Shif t out of Park (automatic). If desired, you can use the
adjustment switches to change the
seat position af ter it is in its
memorized position. If you change
the memorized position, the
indicator in the memory button will
go out. To keep this seat position f or
later use, you must store it in the
driver’s seat position memory.
On vehicles with manual transmission
Driving Position Memory System
Inst rument s and Cont rols
103
Main Menu

The inside mirror can automatically
darken to reduce glare. To turn on
this feature, press the button on the
bottom of the mirror. The AUTO
indicator comes on as a reminder.
When it is on, the mirror darkens
when it senses the headlights of a
vehicle behind you, then returns to
normal visibility when the lights are
gone. Press the button again to turn
of f this f eature.
Keeptheinsideandoutsidemirrors
clean and adjusted f or best visibility.
Be sure to adjust the mirrors bef ore
you start driving.
The inside mirror has day and night
positions. The night position reduces
glare f rom headlights behind you.
Flip the tab on the bottom edge of
the mirror to select the day or night
position.
EX-L and EX-L V6
LX,LX-P,SE,EXandEXV6
Mirrors
104
AUTO BUTTON
INDICATOR SENSOR
TAB
There is also a sensor on the back of
the mirror. Items hung on the mirror
may block this sensor and af f ect its
perf ormance.
Main Menu

Turn the ignition switch to the ON
(II) position.
Move the selector switch to L
(driver’s side) or R (passenger’s
side).Push the appropriate edge of the
adjustment switch to move the
mirrorright,left,up,ordown.
When you f inish, move the
selector switch to the center (off)
position. This turns the
adjustment switch of f to keep your
settings.
The outside mirrors are heated to
remove fog and frost. With the
ignition switch in the ON (II)
position, turn on the heaters by
pressing the button. The indicator in
the button comes on as a reminder.
Press the button again to turn the
heaters off. Pressing this button also
turns the rear window def ogger on
and off.
1. 3.
2. 4.Except U.S. LX, LX-P and SE
PowerMirrorHeaters
Adjusting the Power Mirrors
Mirrors
Inst rument s and Cont rols
105
SELECTOR SWITCH
ADJUSTMENT SWITCH EX-L V6 without navigation system is
shown.REAR WINDOW DEFOGGER/
HEATED MIRROR BUTTON
Main Menu

µ
Turn the ignition switch to the ON
(II) position to raise or lower any
window. To open a window, push the
switchdownandholdit.Releasethe
switch when you want the window to
stop. Pull back on the switch and
hold it to close the window. To open either f ront
window f ully (driver’s window only
on LX), push the window switch
f irmly down to the second detent,
then release it. The window
automatically goes down all the way.
To stop the window f rom going all
the way down, pull back on the
window switch briefly.
To close either f ront window f ully
(driver’s window only on LX), pull
back the window switch f irmly to the
second detent, then release it. The
window automatically goes all the
way up. To stop the window f rom
going all the way up, push down on
the window switch briefly.
AUTO
Power Windows
106
MAIN SWITCH
DRIVER’S
WINDOW
SWITCH FRONT
PASSENGER’S
WINDOW SWITCHINDICATOR
Closing a power window on
someone’s hands or fingers can
cause serious injury.
Make sure your passengers are
away from the windows before
closing them.
Main Menu

µ
Auto reverse stops sensing when the
window is almost closed. You should
always check that all passengers and
objects are away f rom the window
bef ore closing it. If either f ront
window (driver’s window only on
LX) senses any obstacle while it is
closing automatically, it will reverse
direction, and then stop. To close the
window, remove the obstacle, then
use the window switch again.
When you push the main switch in,
the indicator comes on and the
passengers’ windows cannot be
raised or lowered. Use the main
switchwhenyouhavechildreninthe
vehicle so they do not injure
themselves by operating the
windows unintentionally. To cancel
this feature, push on the switch
again. The switch will pop out and
the indicator will go of f .
The windows and the main switch
feature will operate for up to 10
minutes after you turn off the
ignition switch. Opening either f ront
door cancels this f unction.
The driver’s window auto
reverse f unction is disabled when
you continuously pull up the switch.
AUTO REVERSE
Power Windows
Inst rument s and Cont rols
107
NOTE:
Main Menu

Press the UNLOCK button a
second time, and hold it. The
remaining doors unlock, and all
f our windows and the moonroof
start to open. To stop the windows
and moonroof , release the button.You can open and close the windows
and the moonroof (if equipped) with
the key in the driver’s door lock.Turn the key clockwise, then
release it.
Insert the key in the driver’s door
lock.
To open:
Press the UNLOCK button once
to unlock the driver’s door.
You can open all of the windows and
the moonroof (if equipped) f rom the
outside with the remote transmitter. To open the windows and
moonroof f urther, press the
button again (within 10 seconds of
step 1) and hold it. If the windows
and the moonroof stop bef ore the
desired position, repeat steps 1
and 2.
You cannot close the windows or the
moonroof with the remote
transmitter.
1. 2. 3.
1. 2.
Opening the Windows and
Moonroof with the Remote
Transmitter
Opening/Closing the Windows
and Moonroof with the K ey
Power Windows
108
Open
Close
UNLOCK
BUTTON
Main Menu