2011 FORD SUPER DUTY wheel

Operation in standing water
Ingestion of water into the diesel engine can result in immediate and
severe damage to the engine. If driving through water, slow down to
avoid splashing water into the intake. If the engine stalls, and ingestion
of water into the engine is suspected, do not try to restart the engine.
Consult your dealer for service immediately.
Engine block heater (if equipped)
Refer to theDrivingchapter in theOwner’s Guide.
Rapid heat supplemental heating system (if equipped)
The optional rapid heat feature is an electrically powered device that is
designed to provide supplemental heat during engine warm up. For
maximum effectiveness mid to low blower speed is recommended during
initial warm up. When operating in automatic mode (when equipped) the
climate control unit will determine the appropriate blower speed for
existing conditions.
Note:Additional aftermarket electrical loads operated during engine
warm up may impact the performance of the rapid heat supplemental
heater.
DUAL FUEL TANK SELECTOR CONTROL (IF EQUIPPED)
If your vehicle is equipped with dual
fuel tanks, you will have a selector
control, located to the right of the
steering wheel, which allows you to
draw fuel from either tank. Your fuel
gauge will display the amount of
fuel in the currently selected tank.
TRAILER TOWING
Refer to yourOwner’s Guidefor full details on towing a trailer.
Driving
14
2011 Econoline(eco)
Supplement, 1st Printing
USA(fus)

Trailer towing tables
6.7L Engine
Rear axle ratio Maximum GCWR - lb (kg)
F–250 Pick-up
3.31 or 3.55 23500 (10659)
F–350 Single Rear Wheel (SRW) Pick-up
3.31 or 3.55 23500 (10659)
F–350 Dual Rear Wheel (DRW) Pick-up
3.73 26000 (11793)
F–350 Single Rear Wheel (SRW) Chassis Cab
3.73 23500 (10659)
F–350 Dual Rear Wheel (DRW) Chassis Cab
3.73 or 4.10 24500 (10659)
F–450 Dual Rear Wheel (DRW) Pick-up
4.30 33000 (14969)
F–450 Dual Rear Wheel (DRW) Chassis Cab
4.10 26000 (11793)
4.30 30000 (13608)
1
F–550 Chassis Cab
4.10 or 4.88 26000 (11793)
4.30 or 4.88 35000 (15875)
1
1
Requires Optional GCWR Package.
Driving
15
2011 Econoline(eco)
Supplement, 1st Printing
USA(fus)

Coolant change interval
❑6 years or 105,000 miles (168,000 km) - change coolant (whichever comes first) or as indicated from the coolant tests
for concentration (freeze-point) or additive strength (corrosion inhibitor).
❑After initial change - change coolant every 3 years or 45,000 miles (72,000 km) or as indicated from the coolant tests
for concentration (freeze-point) or additive strength (corrosion inhibitor).
❑Use coolant specified in theOwner’s Guideunder theMaintenance and Specificationschapter
❑For special operating conditions, seeSpecial Operating Conditionsat the end of this section
Check every month
❑Check function of all interior and exterior lights❑Check tires for wear and adjust air pressure (including spare tire)
❑Check that holes in the tail-pipe of the exhaust system are clear of debris-the holes/slots are functional
❑Check engine oil level
❑Check windshield washer fluid level
❑Check and drain fuel filter/water separator
❑Check air filter restriction gauge
Check every six months
❑Check lap/shoulder belts and seat latches for wear and function❑Check that externally-mounted spare tire is tight (seeOwner’s Guide)
❑Check power steering fluid level
❑Check washer spray, wiper operation and clean all wiper blades (replace as necessary)
❑Check parking brake for proper operation
❑Check and lubricate all hinges, latches and outside locks
❑Check and lubricate door rubber weatherstrips
❑Check and clean body and door drain holes
❑Check safety warning lamps (brake, ABS, air bag, safety belt) for operation
❑Check engine and secondary cooling system concentration (freeze-point protection), additive strength (corrosion inhibitor),
coolant level and hoses
❑Check battery connections and clean if necessary
Retightening lug nuts
❑On vehicles equipped with single rear wheels, retighten the lug nuts to the specified torque at 500 miles (800 km) after
any wheel disturbance (tire rotation, changing a flat tire, wheel removal, etc.).
❑On vehicles equipped with dual rear wheels, retighten the wheel lug nuts to the specified torque at 100 miles (160 km),
and again at 500 miles (800 km) of new vehicle operation and after any wheel disturbance (tire rotation, changing a flat
tire, wheel removal, etc.).
❑Refer toWheel Lug Nut Torque Specificationin yourOwner’s Guidefor the proper lug nut torque specification.
Scheduled Maintenance Guide
66
2011 Econoline(eco)
Supplement, 1st Printing
USA(fus)

Oil Change Service Interval* 1 2 345678910
Change engine oil and filter• •••••••••
Refill diesel exhaust fluid tank• •••••••••
Rotate tires, inspect tire wear and measure tread
depth. Vehicles equipped with dual rear wheels
should only rotate if unusual wear is observed.• •••••••••
Inspect air filter restriction gauge, replace filter as
necessary• •••••••••
Inspect wheels and related components for abnormal
noise, wear, looseness or drag• •••••••••
Inspect and lubricate steering linkage, ball joints,
suspension, tie rod ends, driveshaft, front axle
U-joints (4WD vehicles)• •••••••••
Perform multi-point inspection (recommended)• •••••••••
Inspect automatic transmission fluid level•••••
Inspect brake pads, shoes, rotors, drums, brake
linings, hoses and parking brake•••••
Inspect exhaust system and heat shields•••••
*Oil change service intervals should be completed as indicated by the instrument cluster message center
Reset your Intelligent Oil Life Monitor™ after each engine oil and filter change; refer to theInstrument Clusterchapter
of theOwner’s Guide
Scheduled Maintenance Guide
69
2011 Econoline(eco)
Supplement, 1st Printing
USA(fus)

Oil Change Service Interval* 11 12 13 14 15 16 17 18 19 20
Change engine oil and filter• •••••••••
Refill diesel exhaust fluid tank• •••••••••
Rotate tires, inspect tire wear and measure tread
depth. Vehicles equipped with dual rear wheels
should only rotate if unusual wear is observed.• •••••••••
Inspect air filter restriction gauge, replace filter as
necessary• •••••••••
Inspect wheels and related components for abnormal
noise, wear, looseness or drag• •••••••••
Inspect and lubricate steering linkage, ball joints,
suspension, tie rod ends, driveshaft, front axle
U-joints (4WD vehicles)• •••••••••
Perform multi-point inspection (recommended)• •••••••••
Inspect automatic transmission fluid level•••••
Inspect brake pads, shoes, rotors, drums, brake
linings, hoses and parking brake•••••
Inspect exhaust system and heat shields•••••
*Oil change service intervals should be completed as indicated by the instrument cluster message center
Reset your Intelligent Oil Life Monitor™ after each engine oil and filter change; refer to theInstrument Clusterchapter
of theOwner’s Guide
Scheduled Maintenance Guide
70
2011 Econoline(eco)
Supplement, 1st Printing
USA(fus)

Perform the services noted in the following table at the specified
time/mileage (km) period either within 3,000 miles (5,000 km) of the
OIL CHANGE REQUIRED message appearing in the message center or
when the time/mileage (km) reading indicates service is due.
Example #1:The OIL CHANGE REQUIRED message comes on at
18,751 miles (30,177 km); perform the 22,500 mile (36,000 km) fuel
filter replacement.
Example #2:The OIL CHANGE REQUIRED message hasnotcome on
but the odometer reads 22,500 miles (36,000 km); perform the fuel filter
replacement. (i.e., Intelligent Oil Life Monitor™ was reset at 15,000 miles
[24,000 km].)
Every 15,000 miles
(24,000 km), 600 hours of
engine operation or as
indicated by the instrument
cluster message centerInspect engine and secondary cooling
system concentration (freeze-point
protection), additive strength
(corrosion inhibitor), coolant level and
hoses
Every 22,500 miles
(36,000 km) or as indicated by
the instrument cluster
message center, whichever
comes firstReplace engine- and frame-mounted
fuel filters
At 45,000 miles (72,000 km) Replace air inlet foam filter
1
Every 60,000 miles
(96,000 km)Replace front wheel bearing grease
and grease seal on 4x2 vehicles (if
non-sealed bearings are used)
At 90,000 miles (144,000 km) Inspect accessory drive belt(s)
2
At 100,000 miles (160,000 km) Change rear axle fluid (Dana axles
only; refer toSpecial operating
conditions)
3
At 105,000 miles (168,000 km)
or 72 monthsChange engine coolant and secondary
coolant4
Scheduled Maintenance Guide
71
2011 Econoline(eco)
Supplement, 1st Printing
USA(fus)

Every 150,000 miles
(240,000 km)Change automatic transmission fluid
Change front axle fluid (4WD vehicles)
Change transfer case fluid (4WD
vehicles)
Replace accessory drive belt(s) if not
replaced in the last 100,000 miles
(160,000 km)
Replace front wheel bearings and seals
on 4x2 vehicles (if non-sealed bearings
are used)
1Replace filter again at 97,500 miles (156,000 km) and 150,000 miles
(240,000 km)
2Initial inspection at 90,000 miles (144,000 km), then every
15,000 miles (24,000 km) thereafter until replacement at 150,000
(240,000 km)
3Initial replacement at 100,000 miles (160,000 km), then again at
150,000 (240,000 km)
4Initial replacement at 105,000 miles (168,000 km) or 72 months or as
indicated from coolant tests for concentration (freeze-point) or
additive strength (corrosion inhibitor); every 45,000 miles (80,000 km)
or 36 months thereafter or as indicated from coolant tests for
concentration (freeze-point) or additive strength (corrosion inhibitor)
Scheduled Maintenance Guide
72
2011 Econoline(eco)
Supplement, 1st Printing
USA(fus)

Note:After initial coolant flush and fill at 60,000 miles (96,000 km) or
2400 hours of operation, flush and fill every 45,000 miles (80,000 km) or
1800 hours thereafter.
If vehicle is operated in sustained ambient temperatures below -10°F
(-23°C) or above 100°F (38°C)
As required– Change engine oil and replace oil filter as indicated by
message center and perform services as listed in the
Scheduled Maintenance chart.
Every 15,000 miles (24,000 km),
6 months, 600 hours of engine
operation, or as indicated by the
message center or instrument
cluster (whichever occurs first)– Change engine- and frame-mounted fuel filters
Every 30,000 miles (48,000 km)– Replace wheel bearing grease and grease seals on 4x2
wheel bearings (if non-sealed bearings are used)
Every 60,000 miles (96,000 km)– Change transfer case fluid (4x4 only)
Perform the services noted in the preceding table at the specified
time/mileage (km) period either within 3,000 miles (5,000 km) of the
OIL CHANGE REQUIRED message appearing in the message center or
when the time/mileage (km) reading indicates service is due.
Example #1:The OIL CHANGE REQUIRED message comes on at
18,751 miles (30,177 km); perform the 22,500 mile (36,000 km) fuel
filter replacement.
Example #2:The OIL CHANGE REQUIRED message hasnotcome on
but the odometer reads 22,500 miles (36,000 km); perform the fuel filter
replacement. (i.e., Intelligent Oil Life Monitor™ was reset at 15,000 miles
[24,000 km].)
Scheduled Maintenance Guide
77
2011 Econoline(eco)
Supplement, 1st Printing
USA(fus)