Page 158 of 396
Use
)
Extract the torch from its location pulling it
upwards.
)
Press the switch, located on the back,
to switch the torch on or off.
)
Unfold the suppor t, located on the back,
to set down and raise the torch; for
example, when changing a wheel.
Storing
)
Put the torch back in place in its location
starting with the lower part.
If you have forgotten to switch off the torch,
this switches it off automatically.
Storage box
)
Raise the boot carpet for access to
the storage box.
This has areas for the storage a box of spare
bulbs, a first aid kit, two warning triangles...
It also contains the vehicle tools, the temporary
puncture repair kit...
It the torch is not engaged correctly,
it may not charge and may not come on
when the boot is opened.
Page 198 of 396
In the event of the electric parking brake
malfunctioning or the battery running flat, an
emergency manual device can release the
parking brake.
)
Immobilise the vehicle (or keep it
stationary, if the brake pedal is pressed),
with the engine running, by engaging
first gear (manual gearbox), position P
(automatic gearbox) or position M
or R
(6 -speed electronic gearbox system).
Emergency release
)
Switch off the engine but leave the ignition
on. If it is not possible to immobilise the
vehicle, do not operate the control and
contact a CITROËN dealer or a qualified
workshop without delay.
)
Fetch the two vehicle blocks B
and the
release device C
, located under the boot
carpet.
)
Immobilise the vehicle by placing the blocks
in front or behind the two front wheels,
opposite to the direction of the slope.
)
Remove the storage box under the boot
carpet for access to the emergency release
device.
Page 199 of 396
197Driving
)
Pierce the protective cover D
on the tube E
with the release device.
)
Place the release device in the tube.
)
Turn the release device clockwise .
For
safety reasons
, it is essential
to continue
turning the device until it reaches its stop.
The parking brake is released.
)
Remove the release device and store it
with the blocks in the toolbox under the
boot carpet.
For safety reasons, after this operation
it is essential to contact a CITROËN
dealer or a qualified workshop without
delay to replace the protective cover.
Following an emergency unlocking,
immobilisation of the vehicle is no
longer assured once the manual
emergency release has been deployed
and the manual control does not allow
the re-application of your parking
brake.
Take no action, either on the control
lever A
, or stopping star ting the engine
while the release device is engaged.
Take care not to allow moisture or dust
in the proximity of the protective cover.
- The operation of the parking brake
reinitialises when the ignition is switched
off then on again. If the reinitialisation
of the parking brake proves impossible,
contact a CITROËN dealer or a qualified
workshop.
- The subsequent time required for
application may be longer than during
normal operation.
Page 246 of 396
Temporary puncture repair kit
Complete system consisting of a compressor
and a sealant car tridge which permits
temporary repair
of a tyre so that you can
drive to the nearest garage.
It is designed to repair most punctures which
could affect the tyre, located on the tyre tread
or shoulder.
Access to the kit
The speed limit sticker I
must be affixed
to the vehicle's steering wheel to remind
you that a wheel is in temporary use.
Do not exceed a speed of 50 mph
(80 km/h) when driving with a tyre
repaired using this type of kit.
Description of the kit
A.
"Sealant" or "Air" position selector.
B.
On "I"
/of f "O"
switch.
C.
Deflation button.
D.
Pressure gauge (in bar or p.s.i.).
E.
Compar tment housing:
- a cable with adaptor for 12 V socket,
- various inflation adaptors for
accessories, such as balls, bicycle
tyres...
F.
Sealant car tridge.
G.
White pipe with cap for repair.
H.
Black pipe for inflation.
I.
Speed limit sticker.
This kit is installed in the storage box, under the
boot floor.
Page 251 of 396
249Practical information
Changing a wheel
Procedure for changing a faulty wheel for the spare wheel using the tools provided with the vehicle.
The tools are installed in the boot under the
floor.
To gain access to them:
)
open the boot,
)
raise the floor,
)
secure it by hooking its cord on the hook
on the rear shelf suppor t,
)
with a standard size spare wheel, unclip
and remove the box in the middle of the
wheel containing the tools,
or
)
with a "space-saver" spare wheel; lift the
wheel at the rear towards you for access
to the storage box containing the tools.
Access to the tools
List of tools
All of these tools are specific to your vehicle.
Do not use them for other purposes.
Wheel with trim
When removing the wheel
, detach the
trim first using the wheelbrace 1
pulling
at the valve passage hole.
When refitting the wheel
, refit the trim
star ting by placing its notch facing the
valve and press around its edge with
the palm of your hand.
3.
"Bolt cover" tool.
For removing the bolt protectors (covers)
on alloy wheels.
4.
Socket for the security bolts (located in the
glove box).
For adapting the wheelbrace to the special
"security" bolts.
1.
Wheelbrace.
For removing the wheel trim and the wheel
fixing bolts.
2.
Jack with integral handle.
For raising the vehicle.
Page 252 of 396
The spare wheel is installed in the boot under
the floor.
Depending on version, the spare wheel may be
a standard size steel or alloy wheel, or for some
countries it is the "space saver" type.
For access to the spare wheel, refer to the
paragraph "Access to the tools" on the previous
page.
Access to the spare wheel
Ty r e u n d e r - i nfl ation detection
The spare wheel is not fitted with a
sensor. The punctured wheel must
be repaired by a CITROËN dealer or
aqualified workshop.
Taking out the standard wheel
)
Unscrew the yellow central bolt.
)
Raise the spare wheel towards you from
the rear.
)
Take the wheel out of the boot.
Page 256 of 396
Fitting a wheel
Fitting a steel or "space-
saver" spare wheel
If your vehicle is fitted with alloy
wheels, when tightening the bolts on
fitting it is normal to notice that the
washers do not come into contact with
the steel or "space-saver" spare wheel.
The wheel is secured by the conical
contact of each bolt.
List of operations
)
Put the wheel in place on the hub.
)
Screw in the bolts by hand to the stop.
)
Pre-tighten the security bolt using the
wheelbrace 1
fitted with the security
socket 4
.
)
Pre-tighten the other bolts using the
wheelbrace 1
only.
After changing a wheel
To store the punctured wheel in the
boot correctly, first remove the central
cover.
When using the "space-saver" type
spare wheel, do not exceed 50 mph
(80 km/h).
Have the tightening of the bolts and the
pressure of the spare wheel checked
by a CITROËN dealer or a qualified
workshop without delay.
Have the punctured wheel repaired and
replace it on the vehicle as soon as
possible.
Page 263 of 396
261Practical information
1.
Brake lamps (P21/5W).
2.
Sidelamps (LEDs).
3.
Direction indicators (PY21W amber)
4.
Reversing lamp (P21W).
5.
Rear foglamps (P21W).
Rear lamps
Amber bulbs, such as those for the
direction indicators, must be replaced
by bulbs of the same rating and colour.
The lamps on the tailgate, other than
the guide lamps, are dummy units.
They are there for aesthetic
purposes only.
Changing stop lamp, reversing lamp and direction indicator bulbs
These three bulbs are changed from inside the boot:
)
open the boot,
)
remove the access grille from the
corresponding side trim panel,
)
slacken the two nuts using a 10 mm tube
spanner then remove the nuts by hand,
)
unclip the lamp unit connector,
)
extract the lamp unit carefully pulling in its
middle towards the outside,
)
remove the foam seal,
)
unclip the two small secondary connectors,
)
spread the two tabs and remove the bulb
holder,
)
turn the bulb a quar ter of a turn and
change it.
To reassemble, carry out these operations in
reverse order.
Take care to engage the lamp unit in its guides,
while keeping it in line with the vehicle.
Tighten sufficiently to ensure sealing, but
without damaging the lamp.
