Page 238 of 396
Changing the coolant
The coolant does not have to be changed.
Coolant specifi cation
The coolant must conform to the
manufacturer's recommendations.
Coolant level
The coolant level should be close
to the "MA X" mark but should never
exceed it.
When the engine is warm, the
temperature of the coolant is regulated by the
fan. This can operate with the ignition off.
On vehicles which are fitted with a par ticle
emission filter, the fan may operate after
the vehicle has been switched off, even if
the engine is cold.
In addition, as the cooling system is pressurised,
wait at least one hour after switching off the engine
before carrying out any work.
To avoid any risk of scalding, unscrew the cap
by two turns to allow the pressure to drop.
When the pressure has dropped, remove
the cap and top up the level.
Power steering fluid level
The power steering fluid level should
be close to the "MA X" mark. Unscrew
the cap, with the engine cold,
to check the level. To check the level or top up the
fluid on vehicle fitted with headlamp
washers, immobilise the vehicle and
switch of the engine.
Screenwash/headlamp wash
level
Page 247 of 396
245Practical information
1. Sealing
)
Uncoil the white pipe G
fully.
)
Unscrew the cap from the white pipe.
)
Connect the white pipe to the valve of the
tyre to be repaired.
Repair procedure
Avoid removing any foreign bodies
which have penetrated into the tyre.
)
Connect the compressor's electric plug to
the vehicle's 12 V socket.
)
Star t the vehicle and leave the engine
running.
)
Switch off the ignition.
)
Turn the selector A
to the
"sealant" position.
)
Check that the switch B
is in
position "O"
.
Take care, this product is harmful
(e.g. ethylene-glycol, colophony...) if
swallowed and causes irritation to the
eyes.
Keep it out of reach of children.
Page 254 of 396
Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does
not block traffic: the ground must be
level, stable and non-slippery ground.
Apply the parking brake unless it has
been programmed to automatic mode,
switch off the ignition and engage first
gear * to lock the wheels.
Check that the braking warning lamps
in the instrument panel are on
(not f lashing).
The occupants must get out of the
vehicle and wait where they are safe.
If necessary, place a chock under the
wheel diagonally opposite the wheel to
be changed.
Never go underneath a vehicle raised
using a jack; use an axle stand.
List of operations
)
Remove the chromed bolt cover from each
of the bolts using the tool 3
(according to
equipment).
)
Fit the security socket 4
on the
wheelbrace 1
to slacken the security bolt.
)
Slacken the other bolts using the
wheelbrace 1
only.
*
position R
for the electronic gearbox system;
P
for an automatic gearbox.
Page 265 of 396
263Practical information
Changing a fuse
The extraction tweezer is fitted to the back of
the dashboard fusebox cover.
For access to it:
)
unclip the cover by pulling at the top right,
then left,
)
disengage the cover completely and turn it
over,
Access to the tools
)
remove carrier on which the tweezer is
fitted.
Changing foglamp bulbs
These bulbs are replaced from outside the rear bumper:
)
pass your hand under the bumper,
)
turn the bulb holder a quar ter turn and
remove it,
)
turn the bulb a quar ter turn, pull it out and
fit a new bulb.
For reassembly, carry out these operations in
reverse order.
Take care not to touch the silencer;
there is a risk of burns if changing a
bulb within a few minutes of switching
off the ignition.
Page 266 of 396
Installing electrical
accessories
Your vehicle's electrical system is
designed to operate with standard or
optional equipment.
Before installing other electrical
equipment or accessories on your
vehicle, contact a CITROËN dealer or a
qualified workshop.
CITROËN will not accept responsibility
for the cost incurred in repairing your
vehicle or for rectifying malfunctions
resulting from the installation of
accessories not supplied and not
recommended by CITROËN and
not installed in accordance with its
instructions, in par ticular when the
combined consumption of all of the
additional equipment connected
exceeds 10 milliamperes.
Before changing a fuse:
)
the cause of the failure must be identified
and rectified,
)
all electrical consumers must b switched off,
)
the vehicle must be immobilised with the
ignition off,
)
identify the failed fuse using the tables and
layout drawings in the following pages.
Changing a fuse
Good
Failed
The replacement of a fuse not shown in
the tables below may cause a serious
malfunction of your vehicle. Contact
a CITROËN dealer or a qualified
workshop.
Tw e e z e r
To replace a fuse, you must:
)
use the special tweezer to extract the fuse
from its housing and check the condition of
its filament,
)
always replace the failed fuse with a fuse
of the same rating (same colour); using a
different rating could cause faults (risk
of fire).
If the fuse fails again soon after replacement,
have the vehicle's electrical system checked by
a CITROËN dealer or a qualified workshop.
Page 273 of 396
271Practical information
Load reduction mode
System which manages the use of cer tain
functions according to the level of charge
remaining in the battery.
When the vehicle is being driven, the load
reduction function temporarily deactivates
cer tain functions, such as the air conditioning,
the heated rear screen...
The deactivated functions are reactivated
automatically as soon as conditions permit. Do not disconnect the terminals while the engine is running.
Do not charge the batteries without disconnecting the terminals first.
Do not push the vehicle to star t the engine if it is fitted with the 6 -speed electronic
gearbox system.
Before disconnecting the
battery
Wait 2 minutes after switching off the
ignition before disconnecting the battery.
Close the windows and the doors before
disconnecting the battery.
Following reconnection
of the battery
Following reconnection of the battery,
switch on the ignition and wait 1 minute
before star ting to permit initialisation of the
electronic systems. However, if problems
are encountered following this operation,
contact a CITROËN dealer or a qualified
workshop.
Referring to the corresponding section,
you must yourself reinitialise:
- the remote control key,
- the GPS satellite navigation system.
Page 275 of 396
273Practical information
Changing a wiper blade
Before removing a front
wiper blade
)
Within one minute after switching off
the ignition, operate the wiper stalk to
position the wiper blades ver tically on the
windscreen.
Removing
)
Raise the corresponding wiper arm.
)
Unclip the wiper blade and remove it.
Fitting
)
Put the corresponding new wiper blade in
place and clip it.
)
Fold down the wiper arm carefully.
After fitting a front wiper
blade
)
Switch on the ignition.
)
Operate the wiper stalk again to park the
wiper blades.
Very cold climate screen *
Removable protective screen which prevents
the accumulation of snow at the radiator
cooling fan.
Fitting
)
Offer up the very cold climate screen to
the front of the lower section of the front
bumper.
)
Press around its edge to engage its fixing
clips one by one.
Removal
)
Use a screwdriver as a lever to release
each fixing clip in turn.
* According to country. Do not forget to remove the very cold
climate screen:
- when the ambient temperature
exceeds 10 °C,
- when towing,
- at speeds above 75 mph (120 km/h).
Page 277 of 396
275Practical information
)
On the front bumper, unclip the cover by
pressing at the bottom.
)
Screw the towing eye in fully.
)
Install the towing bar.
)
On the rear bumper, unclip the cover by
pressing at the bottom.
)
Screw the towing eye in fully.
)
Install the towing bar.
)
Switch on the hazard warning lamps on
both vehicles.
)
Move off gently, drive slowly and for a short
distance.
Towing your vehicle
Towing another vehicle
)
Place the gear lever in neutral
(position N
on the electronic gearbox
system or automatic gearbox).
Failure to obser ve this instruction
could result in damage to
certain components (braking,
transmission...) and the absence of
braking assistance the next time the
engine is started.
)
Unlock the steering by turning the key
in the ignition one notch and release the
parking brake.
)
Switch on the hazard warning lamps on
both vehicles.
)
Move off gently, drive slowly and for a short
distance.
