Page 11 of 324
9Familiarisation
88
Access
A.
Unfolding/Folding the key.
B.
Unlocking the vehicle.
Remote control key
Other functions...
C.
Normal locking of the vehicle
Vehicle location.
1.
Opening the fuel filler flap.
2.
Opening and hooking the fuel filler cap.
Fuel t ank
100, 102
179
Ta n k c a p a c i t y :
- approximately 50 litres (petrol),
- approximately 46 litres (Diesel).
- (depending on version: approximately
30 litres (petrol or Diesel)).
A.
Interior release lever.
B.
Exterior safety catch.
C.
Bonnet stay.
Bonnet
Page 14 of 324
Instruments and controls
1.
Steering lock and ignition.
2.
Audio equipment steering wheel controls.
3.
Wiper/screenwash/trip computer stalk.
4.
Scented air freshener.
5.
Central locking button.
6.
Multifunction screen.
7.
Hazard warning lamp switch.
8.
Central adjustable air vents.
9.
Sunshine sensor
Hi-Fi audio system central speaker.
10.
Passenger's airbag.
11.
Side adjustable air vent.
12 .
Glove box /Passenger's airbag deactivation.
13.
Parking brake.
14 .
Central armrest with storage.
15.
Upper and lower storage.
16.
MyWay or Audio system.
17.
Heating/air conditioning controls.
Page 16 of 324
Sitting comfortably
4.
Head restraint height adjustment.
Other adjustments
Other functions...
Access to rear seats.
Heated seats.
78, 81
1.
Release the adjustment mechanism.
2.
Adjust for height and reach.
3.
Lock the adjustment mechanism.
Steering wheel adjustment
83
For reasons of safety, these operations
must only be carried out with the
vehicle stationary.
Page 35 of 324
33Monitoring
Foot on the
brake pedal
fixed. The brake pedal must be pressed. With the SensoDrive gearbox, press the brake pedal
to star t the engine (lever in position N
).
With an automatic gearbox, with the engine running,
press the brake pedal before releasing the parking
brake, to unlock the lever and come out of position P
.
If you wish to release the parking brake without
pressing the brake pedal, this warning lamp will
remain on.
flashing. With a SensoDrive gearbox, if you
hold the vehicle on an incline using
the accelerator for too long, the clutch
overheats. Use the brake pedal and/or the parking brake.
Automatic wiping
fixed. The wiper control is pushed
downwards. Automatic front wiping is activated.
Passenger's
airbag system
fixed. The control switch, located in the
glove box, is in the " ON
" position.
The passenger's front airbag is
activated.
In this case, do not install a rear-
facing child seat. Turn the control switch to the " OFF
" position to
deactivate the front passenger's airbag.
In this case you can install a rear-facing child seat.
Warning lamp
is on
Cause
Action/Observations
Page 38 of 324
Braking
fixed, associated with
the STOP warning
lamp. The braking system fluid level is too
low. You must stop as soon as it is safe to do so.
Top up with brake fluid recommended by CITROËN.
If the problem persists, have the system checked by a
CITROËN dealer or a qualified workshop.
+
fixed, associated with
the STOP and ABS
warning lamp. The electronic brake force distribution
(EBFD) system has a fault. You must stop as soon as it is safe to do so.
Have it checked by a CITROËN or a qualified
workshop.
Warning lamp
is on
Cause
Action/Observations
Anti-lock Braking
System (ABS)
fixed. The anti-lock braking system has a
fault. The vehicle retains conventional braking.
Drive carefully at reduced speed and contact a
CITROËN dealer or a qualified workshop without delay.
Dynamic stability
control (ESP/
ASR)
flashing. The ESP/ASR regulation is active. The system optimises traction and improves the
directional stability of the vehicle.
fixed. Unless it has been deactivated (button
pressed and its indicator lamp on) the
ESP/ASR system has a fault. Have it checked by a CITROËN or a qualified
workshop.
Page 44 of 324
A few seconds after the ignition is switched
on, the distance recorder resumes its normal
operation. The spanner remains
on
.
The distance remaining may be
weighted by the time factor, depending
on the driver's driving habits.
Therefore, the spanner may also come
on if you have exceeded the two year
ser vice inter val.
Service indicator zero reset
After each ser vice, the ser vice indicator must
be reset to zero.
The procedure for resetting to zero is as
follows:
)
switch off the ignition,
)
press and hold the trip distance recorder
zero reset button,
)
switch on the ignition; the distance recorder
display begins a countdown,
)
when the display indicates "=0"
, release
the button; the spanner disappears. Following this operation, if you wish to
disconnect the battery, lock the vehicle
and wait at least five minutes for the
zero reset to be taken into account.
Retrieving the service information
You can access the ser vice information at any
time.
)
Press the trip distance recorder zero reset
button.
The ser vice information is displayed for a
few seconds, then disappears.
Service overdue
For a few seconds after the ignition is switched
on, the spanner flashes
to indicate that the
ser vice must be carried out as soon as possible.
Example:
the ser vice is overdue
by 300 miles (km).
For a few seconds after the ignition is switched
on, the display indicates:
Page 46 of 324
System which measures the total distance
travelled by the vehicle during its life.
The total and trip distances are displayed for
thir ty seconds when the ignition is switched off,
when the driver's door is opened and when the
vehicle is locked or unlocked.
Total distance recorder
System which measures a distance travelled
during a day or other period since it was reset
to zero by the driver.
)
With the ignition on, press the button until
zeros appear.
Trip distance recorder
System for manual adjustment of the brightness
of the instruments and controls in relation to the
exterior brightness.
Lighting dimmer
Activation
When the lighting is on:
)
press the button to change the brightness
of the instruments and controls,
)
when the level of brightness required is
reached, release the button.
Deactivation
When the lighting is off, or in day mode on
vehicles fitted with daytime running lamps,
pressing the button does not have any effect.
Page 78 of 324
Removing the cartridge
)
Press the dial and turn it a quar ter of a turn
anti-clockwise.
)
Remove the car tridge.
)
Refit its sealing case.
Fitting the cartridge
)
Remove the cartridge from the sealing
case.
)
Install the cartridge (flower at top left).
)
Press the dial and turn it a quar ter of a turn
clockwise.
