Page 126 of 324
1.
Rear parcel shelf
(see the following page for details)
2.
Retaining strap
3.
Location for Hi- Fi amplifier
4.
Stowing rings
5.
Storage box (version equipped with a
temporary puncture repair kit)
(see the following page for details)
or
Tool box (version equipped with a spare
wheel)
(refer to section "Practical Information -
§ Changing a wheel")
Boot fi ttings
Page 127 of 324
125Fittings
To remove the shelf:
)
unhook the two cords,
)
raise the shelf slightly, then unclip it on
each side.
Rear parcel shelf
)
Raise the boot carpet by pulling the strap
upwards to gain access to the storage box.
This has areas for storing a temporary puncture
repair kit, a box of spare bulbs, a first aid kit,
two warning triangles, ...
Storage box
)
refit the boot floor carpet by folding it
slightly in the middle.
Page 192 of 324
Temporary puncture repair kit
Complete system consisting of a compressor
and a sealant car tridge which permits
temporary repair
of a tyre so that you can
drive to the nearest garage.
It is designed to repair most punctures which
could affect the tyre, located on the tyre tread
or shoulder.
Access to the kit
The speed limit sticker I
must be affixed
to the vehicle's steering wheel to
remind you that a wheel is in temporary
use.
Do not exceed a speed of 50 mph
(80 km/h) when driving with a tyre
repaired using this type of kit.
Description of the kit
A.
"Sealant" or "Air" position selector.
B.
On "I"
/of f "O"
switch.
C.
Deflation button.
D.
Pressure gauge (in bar or p.s.i.).
E.
Compar tment housing:
- a cable with adaptor for 12 V socket,
- various inflation adaptors for
accessories, such as balls, bicycle
tyres...
F.
Sealant car tridge.
G.
White pipe with cap for repair.
H.
Black pipe for inflation.
I.
Speed limit sticker.
This kit is installed in the storage box, under the
boot floor.
Page 198 of 324
Changing a wheel
Procedure for changing a faulty wheel for the spare wheel using the tools provided with the vehicle.
The tools are installed in the boot under
the floor.
To gain access to them:
)
open the boot,
)
lift the boot carpet by pulling the strap
upwards,
)
remove the polystyrene storage box,
)
unclip and remove the box containing
the tools.
Access to the tools
List of tools
All of these tools are specific to your vehicle.
Do not use them for other purposes.
Wheel with trim
When removing the wheel
, first
detach the trim using the wheelbrace 1
pulling at the valve passage hole.
When refitting the wheel
, refit the
trim star ting by placing its cut-out at the
valve and press around its edge with
the palm of your hand.
3.
"Bolt cover" tool.
For removing the bolt protectors (covers)
on alloy wheels.
4.
Socket for the security wheel bolts (located
in the glove box).
For adapting the wheelbrace to the special
security wheel bolts (if your vehicle is fitted
with them).
1.
Wheelbrace.
For removing the wheel trim and removing
the wheel fixing bolts.
2.
Jack with integral handle.
For raising the vehicle.
Page 199 of 324
197Practical information
The spare wheel is installed in the boot under
the floor.
According to country, you will have either a
"space saver" spare wheel or a temporary
puncture repair kit.
For access to it, refer to the paragraph "Access
to the tools" on the previous page.
Access to the spare wheel
Fitting the "space-saver"
type spare wheel
If your vehicle is fitted with alloy
wheels, it is normal to notice, when
tightening the bolts on fitting, that the
washers do not come into contact with
the "space-saver" type spare wheel.
The wheel is secured by the conical
contact of each bolt.
Taking out the wheel
)
Unscrew the yellow central bolt.
)
Raise the spare wheel towards you from
the rear.
)
Take the wheel out of the boot.
Page 200 of 324
Putting the wheel back in place
)
Put the box back in place in the centre of
the wheel and clip it.
)
Put the polystyrene storage box back
in place.
)
Refit the boot floor carpet by lightly
folding it in the middle (refer to the section
"Fittings - § Storage box").
)
Put the wheel back in its housing.
)
Unscrew the yellow central bolt by a
few turns then place it in the centre of
the wheel.
)
Tighten fully until the central bolt clicks to
retain the wheel correctly.
On vehicles equipped with a "space-
saver" type spare wheel, the punctured
wheel can be stowed in place of the
"space-saver" wheel; however the boot
floor will not then be flat.
Page 203 of 324
201Practical information
Fitting a wheel
After changing a wheel
To store the punctured wheel in the
boot correctly, first remove the central
cover.
When using the "space-saver" type
temporary-use spare wheel, do not
exceed 50 mph (80 km/h).
Have the tightening of the bolts and the
pressure of the spare wheel checked
by a CITROËN dealer or a qualified
workshop without delay.
Have the punctured wheel repaired and
replace it on the vehicle as soon as
possible.
Do not drive with more than one
temporary-use spare wheel fitted to the
vehicle at one time.
List of operations
)
Put the wheel in place on the hub.
)
Screw in the bolts by hand.
)
Pre-tighten the security bolt (if your vehicle
is fitted with them) using the wheelbrace 1
fitted with the socket 4
.
)
Pre-tighten the other bolts using the
wheelbrace 1
only.
Page 209 of 324
207Practical information
1.
Brake lamps/sidelamps (P21/5W).
2.
Sidelamps (P5W).
3.
Direction indicators (PY21W amber)
4.
Foglamp,
offside
(PR21W red)
Reversing lamp,
nearside
(P21W).
Rear lamps
Amber or red bulbs, such as those
for the direction indicators and rear
foglamp, must be replaced by bulbs of
the same rating and colour.
Changing bulbs
)
Open the boot.
)
Remove the access flap from the
corresponding side trim panel.
)
Unscrew the butter fly nut securing the
lamp unit.
)
Unclip the lamp unit connector.
)
Extract the lamp unit carefully pulling in its
middle towards the outside.
)
Spread the four tabs and remove the bulb
holder.
)
Turn the bulb a quar ter of a turn and
change it.
To refit, carry out these operations in reverse
order.
Take care to engage the lamp unit in its guides,
while keeping it in line with the vehicle.
