2011 CITROEN C4 PICASSO instrument panel

Downloaded from www.Manualslib.com manuals search engine IX
139
DRIVING
ELECTRIC PARKING BRAKE
The electric parking brake operates
as follows:


- automatic application/release

Application is automatic when
the engine stops, release is au-
tomatic on use of the accelerator
(active by default).

- manual application/release

Manual application/release of
the parking brake is possible
by pulling control lever A
while
pressing the brake pedal.


Manual application

With the vehicle stationary, to apply
the parking brake whether the en-
gine is running or not, pull
control
lever A
.


Manual release

With the ignition on or the engine
running, to release the parking
brake, press on the brake pedal, or
the accelerator, pull then release

control lever A
.


- the warning lamp P
in con-
trol lever A
and in the in-
strument panel going off,

- the display of a message
"Parking brake off" in the multi-
function screen. The application of the parking brake
is confi rmed by:


-
the illumination of the warn-
ing lamp P
in control lever A

and in the instrument panel,

- the display of a message
"Parking brake on" in the multi-
function screen.
When the driver’s door is
opened with the engine run-
ning, a beep is heard and a
message displayed if the parking
brake has not been applied.
Before getting out of the vehicle,
check that the warning lamp P
is
on fi xed in the instrument panel
(not fl ashing). The full application of the parking
brake is confi rmed by:
If you pull control lever A

without pressing the brake
pedal, the parking brake
will not be released and
the "Foot on brake" warn-
ing lamp will come on in
the instrument panel.

Downloaded from www.Manualslib.com manuals search engine IX
140
DRIVING

Automatic application,
engine off
With the vehicle stationary, the park-
ing brake is automatically applied
when the engine is switched off.

The application of the parking brake
is confi rmed by:


-
the illumination of warning
lamp P
in control lever A

and in the instrument panel,

Automatic release

The electric parking brake releases
automatically and progressively

when you press the accelerator:


)
Manual gearbox
(fi rst gear or
reverse gear engaged): press
down fully on the clutch pedal
then press on the accelerator
pedal and move off.

)
Automatic gearbox
: accelerate
with the selector in position D
, M

or R
.

)
Electronic gearbox
: accelerate
with the selector in position A
, M

or R
.
Full release of the parking brake is
confi rmed by:


- the warning lamp P
in con-
trol lever A
and in the in-
strument panel going off,

- the display of a message "Parking
brake off" in the multifunction
screen.

When stationary, with the engine
running, do not press the acceler-
ator pedal unnecessarily, as you
may release the parking brake.


Maximum application

If necessary, you can use maximum
application
of the parking brake. It
is obtained by means of a long pull

on control lever A
, until you see the
message "Parking brake on" and an
audible signal is heard.

Maximum application is essential:



- when towing a caravan or a trail-
er, if the automatic functions are
activated but you are applying
the parking brake manually,

- when the gradient you are parked
on is variable in its effect (e.g. on
a ferry, in a lorry, during towing),


- when towing, when loaded or
when parking on a gradient, turn
the front wheels towards the
pavement and engage a gear
when you park,

- after a maximum application, the
release time will be longer.

Before leaving the vehicle,
check that warning lamp P

in the instrument panel is
on fi xed, not fl ashing.
Never leave a child alone inside the
vehicle with the ignition on, as they
could release the parking brake.
- the display of a message
"Parking brake on" in the multi-
function screen.
The normal operating sound will con-
fi rm to you the application/release of
the electric parking brake.

Downloaded from www.Manualslib.com manuals search engine IX
141
DRIVING

To immobilise the vehicle,
engine running
To immobilise the vehicle when sta-
tionary with the engine running, you
must apply the parking brake manu-
ally by pulling
on control lever A
.
The application of the parking brake
is confi rmed by:


- the illumination of warning
lamp P
in control A
and in
the instrument panel,

- the display of a message
"Parking brake on" in the multi-
function screen.
When the driver’s door is opened, a
beep is heard and a message dis-
played if the parking brake has not
been applied.
Before leaving the vehicle,
check that warning lamp P

in the instrument panel is
on fi xed (not fl ashing).


Particular situations

In certain situations (e.g. starting
the engine), the parking brake can
automatically alter its force. This is
normal operation.
To move your vehicle without start-
ing the engine (towing, etc...), but
with the ignition on
, press the brake
pedal and release the parking brake
by pulling
then releasing
control
lever A
.
The full release of the parking brake
is confi rmed by the warning lamp P

(red) in the instrument panel going
off and the display of a message
"Parking brake off" in the multifunc-
tion screen.
If the parking brake malfunctions
while applied or if the battery
runs
fl at, an emergency release remains
possible.


Activation/Deactivation of the
automatic functions *

The automatic application when
the engine is switched off and the
automatic release when you press
the accelerator can be deactivated.
Activation/deactivation is performed
using the confi guration menu of the
multifunction screen. To do so, se-
lect "Vehicle parameters/Comfort/
Automatic handbrake."
The deactivation of these
functions is confi rmed by the
lighting of this warning lamp
in the instrument panel.

* According to country With the automatic functions deac-
tivated, the application and release
of the parking brake are done manu-
ally.

Downloaded from www.Manualslib.com manuals search engine IX
146
DRIVING
HILL START ASSIST
System which holds your vehicle tem-
porarily (approximately 2 seconds)
when starting on a slope, the time it
takes to move your foot from the brake
pedal to the accelerator pedal.
This function is only active when:


- the vehicle is completely station-
ary, with your foot on the brake
pedal,

- in particular conditions on a
slope,

- with the driver’s door closed.
The hill start assist cannot be deac-
tivated.

Operation

Operating fault

If a malfunction of the system oc-
curs, these warning lamps come
on. Contact a CITROËN dealer or a
qualifi ed workshop to have the sys-
tem checked.
On an ascending slope, with the
vehicle stationary, the vehicle is
held for a brief moment when you
release the brake pedal:



- provided you are in fi rst gear or
neutral on a manual gearbox,

- provided you are in position A

or M
with the electronic gearbox
system,

- provided you are in position D
or
M
on an automatic gearbox.
On a descending slope, with the
vehicle stationary and reverse
gear engaged, the vehicle is held
momentarily when you release
the brake pedal.



Do not exit the vehicle while
it is being held in the hill
start assist phase.
If you need to exit the ve-
hicle with the engine running, man-
ually apply the parking brake and
ensure that the warning lamp P

(red) in the instrument panel is on
(not fl ashing).

Downloaded from www.Manualslib.com manuals search engine IX
148
DRIVING
GEAR SHIFT INDICATOR *

System which reduces fuel con-
sumption by advising the driver to
change up on vehicles fi tted with a
manual gearbox.

Operation

The system intervenes only when
driving economically.
Depending on the driving situation
and your vehicle's equipment, the
system may advise you to skip one
or more gears. You can follow this
instruction without engaging the in-
termediate gears.
The gear recommended should not
be considered compulsory. In fact,
the confi guration of the road, the
amount of traffi c and safety remain
determining factors when choosing
the best gear. Therefore, the driver
remains responsible for deciding
whether or not to follow the advice
given by the system.
This function cannot be deactivated.

* According to engine.
Example:


- You are in third gear.

- You press the accelerator pedal
moderately.

- The system may suggest that
you engage a higher gear, if ap-
propriate.
The information appears in the form
of an arrow in the instrument panel
screen.
Depending on your vehicle's equip-
ment, this arrow may be accompa-
nied by the recommended gear.

In the case of driving which
makes particular demands
on the performance of the
engine (fi rm pressure on
the accelerator pedal, for example,
when overtaking...), the system will
not recommend a gear change.
The system never suggests:


- engaging fi rst gear,

- engaging reverse gear,

- engaging a lower gear.

Downloaded from www.Manualslib.com manuals search engine IX
149
DRIVING

Displays in the instrument panel



- The gear lever position is dis-
played in the instrument panel,
on the left on the A and C multi-
function screens and on the right
on NaviDrive and MyWay multi-
function screens.

- A back-lit position grille associ-
ated with the gear lever shows
the position selected.



When the ignition is on, il-
lumination of the service
warning lamp, accompa-
nied by an audible signal and
the message "Gearbox faulty"
indicates a malfunction.


Contact a CITROËN dealer or a
qualifi ed workshop.

For safety:


)
position N
can only be disen-
gaged if you are pressing the
brake pedal.

)
if the gearbox is in position N

but the gear lever position is dif-
ferent, reposition the gear lever
on N
in order to be able to start.



Moving off



)
To start the engine, the gear le-
ver must be in position N
.

)
Press fi rmly on the brake pedal.

)
Operate the starter.

)
When the engine is running,
place the gear lever on R
, A
or
M
as desired.

)
In the instrument panel, check
the position engaged.

)
Release the brake pedal and ac-
celerate.
If the gear lever is not in position N
,
and/or if the brake pedal is not
pressed, the corresponding warning
lamp(s) are displayed and a mes-
sage informs you that at least one of
these two conditions is not met.
In this case, the engine will not start,
recommence the above procedure.
6-SPEED ELECTRONIC GEARBOX SYSTEM
The 6-speed electronic gearbox of-
fers a choice between the comfort of
fully automatic operation or the driving
pleasure of manual gear changing.
You have a choice of two driving
modes:


-
automatic
mode for automatic con-
trol of the gears by the gearbox,

- manual
mode for sequential
changing of the gears by the
driver.


)
Automated mode: gear lever 2
in
position A
.

)
Manual mode: gear lever 2
in po-
sition M
.
In automated mode, temporary man-
ual operation is possible any time by
using one of the paddles 1
.


Mode selection

Downloaded from www.Manualslib.com manuals search engine IX
150
DRIVING

Automatic mode


)

Move the gear lever to A
.



Manual mode

)
Pull the " +
" paddle to change up
a gear.

)
Pull the " -
" paddle to change
down a gear.



When the engine is running,
before accelerating to move
the vehicle, make sure that
the position engaged on the
selector grille or in the instrument
panel is either: R
, A
or M

Do not leave the vehicle with the
engine running in R
, A
or M
.


Operation in automatic mode



)
Move the gear lever to
position A
. The warn-
ing lamp A
comes on in
the instrument panel to
confi rm the selection.
Reverse gear
To engage reverse, the vehicle must
be immobilised with your foot on the
brake pedal.


)

Move the gear lever to R
.

At low speeds, if reverse is selected,
the N
indicator fl ashes and the gear-
box goes into neutral automatically.
To engage reverse, put the gear le-
ver in position N
, then in position R
.

Neutral


)

Move the gear lever to N
.

If the vehicle is moving, do not select
this position even momentarily.

)

Move the gear lever to M
.

The gearbox then functions in auto-
matic mode, without any action on
your part.
It constantly selects the gear that is
best suited to the following condi-
tions:


- driving style,

- road profi le,

- optimum fuel consumption.

Downloaded from www.Manualslib.com manuals search engine IX
151
DRIVING

Operation in manual mode



)
Move the gear lever to
position M
.

Steering mounted paddle controls

The steering mounted paddles are
used for the six forward gears.


Changing gear



)
Pull the " +
" paddle to change up
a gear.

)
Pull the " -
" paddle to change
down a gear. By pulling either of the " +
" or " -
" pad-
dles, you can exercise temporary
control over the gearbox.
The request to change gear will be
taken into account. You will still be
in automatic mode. The warning
lamp A
remains on in the instrument
panel.
This function enables you to antici-
pate certain situations such as the
approach of a bend or the need to
overtake another vehicle.

Cancellation of automatic mode
The change from position A
(driv-
ing in automatic mode) to position M

(driving in manual mode) or vice
versa can be made at any time. The
warning lamp A
goes off in the in-
strument panel.

Temporary manual operation
when in automatic mode