Page 31 of 164
1
Monitoring
29
Service indicator
When the ignition is switched on, press
button A
several times in succession until
the ser vice indicator is displayed in the desired
units.
This point can be indicated in one of two ways:
- the miles (km) remaining,
- the time remaining to the next ser vice.
Operation
1.
The screen indicates that 620 miles
(1 000 km) or 1 month remain before
the next service.
2.
The screen indicates that the date for
the ser vice has been exceeded.
Every time the ignition is switched on,
the ser vice spanner is displayed for a
few seconds to remind you that a ser vice
should be carried out as soon as possible.
3.
Once the ser vice has been carried out,
the distance or the number of months to
the next ser vice is displayed again.
System which informs the driver when
the next ser vice is due in accordance with
the manufacturer's ser vicing schedule.
The point at which the next ser vice is due
is calculated from the last ser vice indicator
zero reset.
System for manual adjustment of the brightness
of the instruments and controls in relation to
the exterior brightness.
With the lighting on or off, press button A
to
select the function, then hold down to change
the intensity of the lighting of the instruments
and controls in "day" or "night" mode.
The intensity of the lighting increases each time
button A
is pressed.
When the lighting reaches the maximum
setting, press again to change to the minimum
setting.
When the lighting reaches the required
intensity, release button A
.
The setting is saved when you release button A
and retained when the ignition is turned OFF.
Lighting dimmer
Page 32 of 164
i
i
i
Monitoring
30
This function gives an estimate of the number
of miles (km) that your vehicle can still cover,
based on the recent conditions of use (driving
style, use of heating, air conditioning...).
Range indicator
When the remaining range falls to a low level,
"- - -"
is displayed in the instrument panel.
The display of "---"
, indicating that
the ser vice date has arrived, comes on
automatically after a cer tain time and
distance travelled. The screen then
indicates the time remaining before
the next ser vice is due.
Resetting the service indicator to zero
After each ser vice, the ser vice indicator should
be rest to zero.
The procedures is as follows:
)
Switch off the ignition (switch in the LOCK
or ACC position).
)
Press the reset button A
several times in
succession until the ser vice indicator is
displayed.
)
Press and hold the reset button for a few
seconds until the spanner flashes
.
)
Press the reset button while the spanner is
flashing to change the display from "---"
to
"CLEAR"
.
The distance (or time) remaining before
the next ser vice is due is displayed. The range can be displayed in miles or
kilometres.
To change the units, refer to the
"Distance recorder" section.
Page 111 of 164
8
Practical information
109
Access to the fuses
)
Open the bonnet (refer to the "Checks"
section),
)
Unclip the cover and remove it completely
by pulling towards you.
)
Change the fuse (refer to the
corresponding paragraph).
)
When you have finished, close the cover
carefully to ensure sealing of the fusebox.
Fuse N°
Rating
Functions
11
10 A
On-board charger.
12
10 A
Direction indicator.
13
10 A
Horn.
14
10 A
Daytime running lamps.
15
15 A
Battery fan.
16
10 A
Air conditioning compressor.
17
20 A
Right hand dipped beam.
18
20 A
Left hand dipped beam, headlamp adjusters.
19
10 A
Right hand main beam.
20
10 A
Left hand main beam.
Page 131 of 164
02
1
12
2
3
129
RADIO
Press SRC/TEL several times in
succession and select the FM1 or FM2
radio band.
Press a button to listen to the
corresponding preset station.
Select the desired radio station and
confi rm by pressing "OK"
.
RADIO
Press LIST
to display the list of stations
received in alphabetical order.
The exterior environment (hills, buildings, tunnel, car park, below ground...) may prevent reception, even in RDS station tracking mode.
This phenomenon is normal in the propagation of radio waves and is in no way indicative of a fault with the audio system.
A long press on LIST
builds or updates
the list of stations; audio reception is cut
momentarily.
Make a long press on one of the buttons
to preset the station being heard.
The name of the station is displayed
accompanied by an audible signal to
confi rm the preset.
A press changes to the next or previous
letter (e.g. A, B, D, F, G, J, K, ...).
MANAGE THE LIST
PRESETTING AND SELECTING A STATION
