2011 Citroen BERLINGO FIRST headlamp

73 PRACTICAL INFORMATION
-


1.
Power steering reservoir

2.
Windscreen and headlamp wash
reservoir

3.
Coolant reservoir
4.
Brake fl uid reservoir

5.
Battery

6.
Air fi lter
7.
Dipstick

8.
Engine oil reservoir

1.6 LITRE PETROL ENGINE

PRACTICAL INFORMATION
74 -


1.
Power steering reservoir

2.
Windscreen and headlamp wash
reservoir

3.
Coolant reservoir
4.
Brake fl uid reservoir

5.
Battery

6.
Air fi lter
7.
Dipstick

8.
Engine oil reservoir

1.9 LITRE DIESEL ENGINE

75 PRACTICAL INFORMATION
-


1.
Power steering reservoir.

2.
Windscreen/headlamp wash
reservoir.

3.
Coolant reservoir.
4.
Brake fl uid reservoir.

5.
Battery.

6.
Air fi lter.
7.
Dipstick.

8.
Engine oil reservoir.

9.
Priming pump.

1.6 LITRE TURBO DIESEL HDI ENGINE

77 PRACTICAL INFORMATION
-
CHECKING THE LEVELS

Dipstick

Oil change
According to the information given in
the servicing booklet.

Note:
avoid used oil coming into
prolonged contact with the skin.
Empty the used oil into the contain-
ers intended for this purpose in the
CITROËN network.
Viscosity selection
In all cases, the oil selected must meet
the manufacturer's requirements.

Note:
the coolant does not need to
be changed.

For vehicles equipped with a parti-
cle fi lter, the engine fan may operate
after the ignition has been switched
off, even when the engine is cold.



There are two marks
on the dipstick:

A
= maximum
Never fi ll past this
mark.

B
= minimum

To maintain the reliability
of engines and emission
control systems, the use
of additives in engine oil
is prohibited.


Brake fluid level:

The brake fl uid must be changed according
to the manufacturer's servicing schedule.
Use fl uids recommended by the
manufacturer, which fulfi l DOT4 stan-
dards.

Note:
brake fl uid is harmful to health
and very corrosive. Avoid all contact
with the skin.


Cooling system

Use the fl uid recommended by the
manufacturer.
When the engine is warm, the tem-
perature of the coolant is controlled
by the engine fan. As this fan can op-
erate with the ignition key removed
and because the cooling system is
pressurised, wait for at least one hour
after the engine has stopped before
carrying out any work.
Slacken the cap by two turns to release
the pressure to prevent any risk of scald-
ing. When the pressure has dropped, re-
move the cap and top up the level.

Used oil

Do not dispose of used oil, brake fl uid or
coolant into drains or onto the ground.


Power steering reservoir



)
Open the reservoir, with the en-
gine at ambient temperature. The
level should always be above the
MIN. mark and close to the MAX.
mark.



Windscreen and headlamp
wash level
For best quality cleaning and for
your safety, we would advise that
you use products recommended by
CITROËN.
For optimum cleaning and to prevent
freezing, this fl uid must not be topped
up or replaced with water.


Oil level



)
Check the level regularly and top up
between changes. The maximum
consumption is 0.5 l per 600 miles
(1 000 km).

Check the level with the vehicle level,
engine cold, using the oil level gauge
on the instrument panel or the dipstick.

PRACTICAL INFORMATION
82 -
CHANGING A BULB

Front lamps

To replace a dipped/main beam
headlamp or sidelamp bulb:

Remove the grille



- Remove the screw ( 1
).

- Unclip the lug ( A
) of carrier ( 2
) on
each side.

- Remove the grille ( 3
).
Partially remove the wheelarch liner


- Remove the screws ( 1
),

- Remove the screw ( 2
),

- Remove the plastic pins ( 3
).

83 PRACTICAL INFORMATION
-

Partially remove the bumper



- Remove the screws ( 1
),

- Remove the screws ( 2
),
- Pull lightly on the side of the bum-
per ( 3
),

- Push in the direction of the ar-
row ( B
), on the latch ( A
), via the
opening ( C
),

- Maintain a light sideways pull on
the bumper,

- Push the bumper sharply for-
wards to release the clips at ( D
).
Remove the headlamp



- Remove the screws ( 1
),

- Unclip the index pin on the head-
lamp ( A
),

- Disconnect the connector ( B
) on
the back of the headlamp,

- Remove the headlamp ( 2
).

PRACTICAL INFORMATION
84 -

Dipped/Main beam headlamps
(H4-60/55W)
After following the procedure for re-
moval of the headlamp:

- Turn and remove the protector ( 6
),
- Disconnect the connector ( C
),

- Unclip the spring ( D
),

- Remove and replace the bulb ( 3
).

85 PRACTICAL INFORMATION
-

Side lights (W 5 W)
After following the procedure for re-
moval of the headlamp:


- Turn and remove the protector ( 6
).

- Unclip the the bulb holder ( E
).

- Disconnect the connector ( F
),

- Remove and replace the bulb ( 1
).

Reassembly
Carry out the operations in reverse
order to reassemble. Check that the
lamps are working correctly.


Direction indicator side
repeaters (WY 5 W amber)


- Push the lens to the front or rear
and pull it out.

- Turn the bulb holder a quarter turn.

- Replace the bulb.
Amber coloured bulbs (di-
rection indicators and side
repeaters) must be replaced
by bulbs of the same rating
and colour.