2011 AUDI S8 engine

2 70 Fu ses and bulb s
Luggage compartment fuse assignment
Fig. 208 Luggage co mpar tment: fuse panel with plastic b racket
Fu se pan el A (black ) Fuse panel
@ (b lac k)
I
No.
Equ ipment Amps No
. Equipment
Amps .
l!l button, data logger, diag-
1 nostic con
nector, adaptive
5 10
Rear seat heating, refrigera-
5 j tor, interior rearview mirror
lighting system 11 Dynam
ic steer ing 5
2 Networking gateway
5 12
Selector lever, BCM-2
5
3 adaptive air suspension
5 13 Audi side ass
ist 5
4 Parking system 5 14 Engine control module
5
5 Steering column
lever
5 1
5 Starter 40
I 6 Suspension control system
5
sensor left headlight/Headlight
'
16
10/5
range control system
.
7 Belt tensioners, airbag con-
5
trol module Fuse pan el@ (red)
No. Equipment Amps
Heated washer fluid nozzles,
Homelink (garage door
8 opener), night vision system
5
control module, sport differ- 1
left reversib
le be lt tens ioner
25
2 II
R_ight reversible belt ten-
25
s1oner
ential, ioniser 3
Starter diagnos
is
5
9
Electromechan ica l park ing
5
brake con tro l module 4 DC/DC converter
7,5
5 Adaptive cruise control 7,5

272 Fuses and bulbs
Fuse panel ® (brown)
No. Equipment
= 11 Radio receiver Cell phone adapter, cell
12 phone/telephone charging
cradle, chip card reader (not
i n all countries)
Bulbs
Replacing light bulbs Amps
= 7,5
5
For
your safety, we recommend that you have
your authorized Audi dealer replace burned
out bulbs for you.
It is becoming increasingly more and more
difficult to replace vehicle light bulbs since in
many cases, other parts of the car must first
be removed before you are able to get to the
bulb . This applies especially to the light bulbs
in the front of your car which you can only
reach through the engine compartment .
Sheet metal and bulb ho lders can have sharp
edges that can cause serious cuts, and parts must be correctly taken apart and then prop­
erly put back together to help prevent break ­
age of parts and long term damage from wa­
ter that can enter hous ings that have not been
properly resealed.
For your safety, we recommend that you have
your author ized Audi dealer replace any bulbs
for you, since your dealer has the proper tools,
the correct bulbs and the expertise.
Gas discharge lamps (Xenon lights):
Due to the high electrical vo ltage, have the
bulbs replaced by a qualified technician.
H eadlights with Xenon light can be identified
by the high voltage sticker.
LED headlights* require no maintenance .
Please contact your authori zed Audi dealer if a
bulb needs to be replaced.
A WARNING
Contact with high-voltage components of
the electrical system and improper re- placement
of gas discharge (Xenon) head­
light bulbs can cause serious personal in­
jury and death.
- Xenon bulbs are pressurized and can ex­
plode when being changed.
- Changing Xenon lamps requires the spe­
cial training, instructions and equip­ ment.
- Only an authorized A udi dealer or other
qualified workshop should change the bulbs in gas discharge lamps.
A WARNING
There are parts with sharp edges on the
openings and on the bulb holders that can
cause ser ious cuts.
- If you are uncertain about what to do,
have the work performed by an author­
ized Audi dealer or other qualified work­
shop. Serious personal injury may result
from imprope rly performed wo rk.
(D Tips
- If you must replace the light bulbs your­
self, a lways remember that the eng ine
compartment of any vehicle is a hazard­
ous area to work in. A lways read and
heed all WARNINGS¢
page 216, Engine
compartment¢ &..
-It is best to ask your authorized Audi
dealer whenever you need to change a
bulb.

Emergency situations
General
This chapter i s intended for trained emer­
gency crews and working personnel who have the necessary tools and equipment to
perform these operations.
Starting by pushing or
towing
CD Note
Ve hicles w ith an automatic tra nsmission
cannot be started by pus hing o rtowi ng.
Starting with jumper
cables
If necessary, the engine can be started by
connecting it to the battery of another vehi ­
cle.
If the engine shou ld fail to start because of a
discha rged o r wea k battery, the battery can be
connected to the battery o f
another vehicle,
using a
pair of jumper cables to start the en­
g ine.
Jumper c ables
Use only jumper cables of sufficiently la rge
c ross section to carry the starter c urrent safe­
l y . Refer to the man ufacturer's specifications.
Use only jumper cables with
insulated te rm i­
na l clamps wh ic h are d istinctly mar ked:
plus(+) cable in mos t cases co lore d red
minus (-) cable
in most cases colored black .
A WARNING
Batterie s contain e lec tricity, ac id, an d gas.
Any of these can cause ve ry ser io us or fatal
inju ry. Follow the ins tructions below f or
safe han dling of your veh icle's b attery .
- Alway s sh ield you r eye s and avoid lean­
i n g over the bat te ry w henever possib le.
- A dis ch arged battery c an free ze at tem­
pera tures ju st below 3 2 °F ( 0 °C ). Befo re
Emergency situations 273
connecting a jumpe r cab le, you must
thaw the fr ozen battery c omp lete ly, ot h­
erwise it could explode.
- Do not allow battery acid to contact eyes
or skin. Fl ush any contacted area with
wate r immediately .
- Improper use of a booster battery to start a vehicle may cause an explosion.
- Vehicle batter ies genera te exp losive gas­
es. Keep spar ks, flame and lighted c iga ­
rettes away from batte ries.
- Do not try to jump start any ve hicle w ith
a low ac id leve l in the battery.
- The vo ltage of the booste r batte ry m ust
a lso have a 12-Vol t rating. T he capacity
(Ah) of the booster battery sho uld not be
lowe r tha n that of the discharged bat­
tery . U se of batte rie s of d iffe ren t voltage
or substantially d iffe rent "Ah" rat ing
may c au se an exp losion and persona l in ­
Ju ry.
- N ever cha rge a fro zen battery. Gas tr ap­
pe d in the i ce m ay cause a n ex plosion.
- Never cha rge or use a batte ry tha t h as
been fr ozen . T he battery case may have
be weakened.
- Us e of batter ies of differe nt voltage or
sub stant ia lly diffe ren t ca pa city (Ah) rat­
i ng may c ause an exp losion an d injury .
Th e capac ity (Ah) of the booster bat tery
should not be lower than that of the dis ­
charged batte ry .
- Before you chec k any thing in the engine
compa rtment, always read and hee d all
WARNINGS
¢page 216, Engine com­
partment.
CD Note
- App lying a higher voltage booster ba t­
tery will cause expens ive damage to se n­
sit ive e lectronic components, such as
cont rol units, relays, rad io , etc.
- There must be no electrical contact be­
tween the vehicles as otherwise current
cou ld already start to f low as soon as the
posit ive(+) term inals a re connected. ..,. •
•

2 7 4 Emergency situations
@ Tips
-The discharged battery must be properly
connected to the vehicle's electrical sys­
tem. When jump starting or charging the
battery, never connect the negative
ground cable to the battery negative
post because the battery manager sys­
tem must be able to detect the battery 's
state of charge. Always connect the neg­
ative g round cable to the negative
ground post of the battery manager con­
trol unit .
Use of jumper cables
Make sure to connect the jumper coble
clomps in exactly the order described below!
Fig . 209 Engine compartme nt: connecto rs for jump
start cab les and a charger
Fig. 210 Jump starting w ith the battery of another ve ­
h icle: A - boos ter battery, B - discharged veh icle battery
The procedure described below for connecting
jumper cables is intended to provide a jump
start for your veh icle.
Vehicle with discharged battery :
.. Turn off lights and accessories, move lever
of automatic transmission to
N (Neutral) or
P (Park) and set parking brake.
Connect POSITIVE(+) to POSITIVE(+)
(red)
.. Open the red cover on the positive terminal
¢fig. 209 .
1. Connect one end of the red positive cable
on the
jump start bolt ¢ fig. 210@ (bolt
under the red cover = "positive") of the ve­
hicle to be started @.
2 . Connect the other end to the positive ter-
mi nal @of the booster battery@.
Connect NEGATIVE (-) to NEGATIVE (-)
(black)
3. Connect one end of the black negative ca­
ble to the negat ive terminal @ of the
booster battery @.
4. Connect the other end to the
jump start
pin © (bolts with hex head bolt= "nega­
tive") of the vehicle to be started @.
Starting the engine
.. Start the engine of the veh icle w ith the
booster battery @. Ru n the engine at a
moderate speed .
.. Start engine with discharged vehicle battery
@ in the usual manner .
.. If the engine fails to start, do not keep the
starter crank ing for longer than 10 seconds.
Wait for about 30 seconds and then try aga in .
.,. With engine running, remove jumper cables
from both vehicles in the exact
reverse or­
de r .
.. Close the red cover on the positive term inal.
T he battery is vented to the outside to prevent
gases from entering the vehicle inter ior. Make
s ur e that the jumper clamps are well connect­
ed with their meta l parts in full contact with
the battery terminals.
_& WARNING
To avoid se rious personal injury and dam­
age to the vehicle, heed all warnings and
in structions of the jumper cable manufac­
turer. If in doubt, call for road service .
- Jumper cables must be long enough so
that the veh icles do not touch.
-

-When connecting jumper cables, make
sure that they cannot get ca ught in any
moving parts in the eng ine compart­
ment .
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS ¢
page 216, Engine com­
partment.
(D Note
Imprope r hook-up of jumper cables can r u­
in the generator.
- Always connect POSITIVE( +) to POSI ­
TIVE(+), and NEGA TIVE( -) to NEGATIVE
( - ) ground post of the battery manager
control u nit.
- Check that all sc rew plugs on the battery
ce lls are screwed in firmly. If not, tighten
pl ugs p rio r to conn ecting clamp on nega­
tive batt ery terminal.
- P lease note that the procedure for con­
nect ing a jump er cable as describe d
above applies spec ifica lly to the case of
you r vehi cle be ing j ump s tarte d. When
you are giv ing a jump star t to an othe r ve­
hicle, do
not connec t the negative( -) ca ­
b le to the negat ive (-) term inal on the
discharged battery@¢
fig. 210. In­
stead, securely connect the negative(-)
cable to e ithe r a solid metal component
that is firmly bolted t o th e engine block
or to the engine block itself.
If the bat­
te ry tha t is b eing cha rged does not vent
to the outside, es ca ping b attery gas
could ignite and ex plode!
Emergency towing
with commercial tow
truck
General hints
Your Audi requires special handling f or tow­
ing .
The fo llow ing informa tion is to be us ed by
commercia l tow tr uck operators who know
h ow to ope rate thei r equipmen t sa fe ly.
Emergency s itu ations 2 7 5
- Ne ver tow your Audi. Towing will caus e
damage to the engine and tran smission.
- Never wrap the safety chain s or winch ca­
ble s around the brake lines.
- To prevent unnece ssary damage , your Audi
must be transported with a flat bed truck.
- To load the vehicle on to the fl at bed , use
the towing loop found in the vehicle tools
and attach to the front o r rear anchora ge
¢page 275 and ¢page 276.
_& WARNING
A vehicle being towed is not safe for pas ­
sengers. Never allow anyo ne to ride in a
vehicle be ing towed, for any reason.
-
Front towing loop
Only install the front towing loop when it is
needed.
F ig. 21 1 Front bu mpe r: cove r
Fig. 212 Front bu mpe r: in stall ing t he tow ing loop
There are threads located behind the right
s ide of the front b umpe r where a towing loop
can be installed. The th reads are located be­
hind a cover.
.. Remove the tow ing loop from the vehicle
t oo l kit .

2 78 Emergency situations
-When removing heavy components like
these, ancho r vehicle to ho ist o r add cor­
responding weig hts to ma inta in the cen ­
ter of g ravity. Othe rwise, the vehicle
m ight tilt o r slip off t he hoist, causi ng
serious p erson al inju ry .
@ Note
- Be awa re of the following points befo re
li fting the vehicle:
- The vehicle should never be lifted or
jacked up from underneath the engine
oil pan, the transmission housing , the
front or rear axle or the body side membe rs. This could lead to serious
damage.
- To avoid damage to the underbody or
chassis frame, a rubber pad must be
inserted between the floor jack and
the lift points.
- Before driving over a workshop hoist,
check that the vehicle we ight does not
exceed the permissible lifting capacity
of the hoist .
-Before driving over a workshop hoist,
ensure that there is sufficient clear­
ance between the hoist and low parts
of the vehicle.

General information Explanation of
technical data
Som e of t he technical data listed in this man ­
ual requires further explanation .
The technical data for your vehicle is listed in
the charts starting on
Q page 282 . This sec­
tion provides general information, notes and restr ictions wh ich app ly to this data.
Vehicle identification
The key data is given on the vehicle identifi ca­
tion number (V IN) plate and the vehicle data
sti cker .
Fig. 21 8 Vehicle Ident ificat io n Num ber (V lN) p la te: lo ­
cation o n dri ver"s s ide dash pa nel
Fi g. 2 19 The ve hicle ident ificat ion label -inside the
l u ggage co mpartme nt
The Vehicle Identification Number (VlN)
is located on the d river's side so tha t it is v is i­
b le from the outside through the windshield
Q fig . 218. You can also d isplay the Vehicle
Identification N umber of your vehicle in the
MMI. Select: Function button
ICAR I > Car sys­
tems
> VIN number .
General inform ation 2 79
The vehicle identification label
is located in the l uggage comp artment in the
spare whee l we ll.
T he label
~ fig. 219 shows th e fo llow ing vehi­
cl e data :
(D Product ion cont ro l No .
@ Vehicle identific ation No.
@ Type code number
© Type designat ion/e ngine o utput in K ilo-
wat ts
® Engine and transm ission code letter
® Pa int No./lnterior
0 Optio nal eq uipmen t No.'s
Vehicle data 2 to 7 are a lso fo und in your War­
ranty
& Mai nte nance booklet.
The safety compliance sticker
is your assurance that your new vehicle com­
plies wi th all applicab le Fede ral Motor Vehicle
Safety Standards which were in effect at the
time t he ve hicle was manufactur ed . You can
find this sticke r o n the left doo r jamb.
It
shows the m onth and ye ar of pro duction and
t h e ve hicle ident ifi cat io n number of yo ur vehi ­
cle (perforation) as well as the G ross Vehicle
Weight Rating (GVW R) and the Gross Axle
Weight Rating (GAWR).
The high voltage warning label
i s lo cated on the lock ca rrie r.
The spark ignition system complies with
the Canadian standard ICES-002.
Weights
Gross Vehicle Weight Rating
T he Gro ss Vehicle Weigh t Rat ing (GVWR), and
the Gross Axle We igh t Ra tin g (GAWR) for
fron t and rear are listed on a sticker on the
l eft door jamb .
T he Gro ss Vehicle Weigh t Rat ing incl udes the
weight o f the bas ic vehicle plus f ull fuel t ank,
oi l and coo lant, p lus maximum load, which in­
cludes passen ger we ight (150 lbs/68 kg per ..,.

282 Data
Data
372 hp, a-cylinder engine, with all wheel drive
Appl ies to vehicles: with 8-cy linder engine and a ll whee l drive
Engine data
Maximum output SAE net
Maximum torque SAE net
No . of cylinders
Displacement
Stroke
Bore
Compression ratio hp@rpm
l
b-ft@ rpm
CID (cm
3 )
in (mm)
i n (mm)
372 @6800
328@3500
8 cylinder
254.3 1 (4163)
3 .65 (92,8)
3.33 (84,5)
12.5: 1
Fuel Premium unleaded (91 AKI)
Recommended for maxi­
mum engine performance. Further details<=>
page 218,
Gasoline
Dimen sion s (appro x.)
Length (with license plate bracket)
Width (across mirrors)
He ight (unloaded) in (mm)
in (mm)
in (mm)
T urning circle diameter (curb to curb) ft . (m)
Capacities (approx.) Fuel tank
- Total capacity gal (liters)
- Reserve (of total capacity) gal (liters)
Windshield and headlight washer quarts (liters)
fluid container
Engine oil with filter change quarts (liters)
AS
202.24 (5137)
83.11 (2111)
57 .48 (1460)
4 0.35 (12.3)
ASL
207 .4 (5267)
83.1 1 (2111)
57 .9 (1471)
4 1.67 (12, 7)
23.8 (90 .0)
3 .17 (12)
5 .28 (5)
8 .14 (7.7)