2011 AUDI S3 technical data

_____________________________________________ E_ m __ e_r-=g =- e_ n_c -==y "- s_i_ t _u _a _ t_ i_ o _ n_ s _ __.fflll
Fig. 201 Rear
bumper: towing loop
inserted
On the right side of the rear bumper there is a threaded hole
for the towing loop. The threaded hole is behind a cover.
Note that the towing loop has a
left-hand thread!
Remove the towing loop from the vehicle toolkit
=> page 270.
Place the screwdriver against the upper edge of the cover
and carefully pry it out :::>
page 290, fig. 200.
- Insert the towing loop into the threaded hole=> fig. 201
and turn it all the way in until it is seated securely, then
tighten it with the wheel bolt wrench.
When it is no longer needed, unscrew the towing loop and put it back
into the vehicle toolkit. Be sure to have the towing loop stored in the
vehicle at all times.
& WARNING
If you do not screw the towing loop completely, it could come out
of the threaded hole while the vehicle is being towed causing
damage to the vehicle and possible serious personal injury. •
Vehicle OP-eration
Loading the vehicle onto a flat bed truck
Front hook up
N (0 :? 0:. CD
"'
Fig. 202 Vehicle on
flat bed truck
- Align the vehicle with the centerline of the car carrier
ramp.
- Attach the winch hook to the front towline eye
=>
page 290, fig . 199 previously installed .
Rear hook up
-Align the vehicle with the centerline of the car carrier
ramp.
- Attach the winch hook to the rear towline eye=> fig. 201
previously installed.
rn Tips
Check carefully to make sure the hook-up is secure before moving the
car up the flatbed truck ramp. •
Vehicle care Do-it-yourself service iTechnical data

_______________________________________________ E_ m_ e_r_, g::;._ e_n _ c""' y:.- s_ it_u_ a_t _ i_o _n_ s __ _
If you must lift your vehicle with a floor jack to work underneath,
be sure the vehicl e is safely supported on stand s intended for this
purpo se .
Front lifting point
The lifting point is located on the floor pan reinforcement about at
t he s ame leve l as the jack mo unting point~
page 292, fig. 2 03. Do
not lift the vehicle at th e vertical sill re inforcement.
Rear lifting point
The lifting po int is located on the ve rtical reinforcement of the lower
sill fo r the onboard ja ck ~
page 29 2, fig. 2 04.
Lifting with vehicle jack
Refe r to ~ page 2 76 .
0 Note
• Be aware of the following points before lifting the vehicle:
- The vehicle should never be lifted or jacked up from under ­
neath the engine oil pan , the tran smission housing , the front or
rear axle or the body side members. This could lead to serious
damage.
- To avoid damage to the underbody or chassis frame, a rubber
pad must be inse rted between the floor ja ck and the lift points.
- Before dr iving ov er a workshop hoist , check that the vehicle
weight does not exceed the permissible lifting capacity of the hoist.
- Before driving over a work shop hoi st, en sure that there is
sufficient clearance between the hoist and low parts of the
vehicle. •
Safety first Vehicle care Do-it-yourself service Technical data

.,,___G_ e_ n _ e_ r_ a_ l_i_n _f_o _ r_ m __ a_t _ i_o _n _______________________________________________ _
General information
Explanation of technical data
Some of the technical data listed in this manual requires
further explanation.
The technical data for your vehicle is listed in the charts starting on
~ page 296. This sect ion prov ides genera l information, notes and
restrictions which app ly to this data .•
Veh icle identification
The key data are given on the vehicle identification
number (VIN) plate and the vehicle data sticker .
Fig. 20 5 Vehi cle I den ­
t ifi ca tion Nu mbe r
(VIN) pla te : loc atio n
o n d rive r's sid e d ash
p an el Fi
g. 2 06 Th e vehicle
identi ficati on l abel -
in side the l ugga ge
co mpa rtme nt
The Vehicle Ident ifi cat ion Number (VIN)
is located on the dr iver's s ide so that it is visible from the outside
through the windsh ield -see~ fig. 205 .
The vehicle identificati on label
is located in the luggage compartment in the spare wheel well.
The labe l~ fig. 206 shows the following vehicle data:
© Production control no.
@ Vehicle identification no.
@ Type code n umber
© Type designat io n/eng ine output in Kilowatts
© Engine and transmiss ion code letter
© Paint no./Interior
0 Optional equipment no.'s
Vehicle data 2 to 7 are also found in your Warranty & Maintena nce
booklet.
The safety comp liance stick er
is your assurance that your new vehicle complies w ith all applicable
Federal Motor Veh icle Safety Standa rds which we re in effect at the
time the vehicle was manufactured. You can find this sticker on the ._

________________________________________________ G ..... e_ n_e ___ ra ___ l_i_n _ f_ o ___ r_m :....:....: a ..... t ..... i...: o ..... n---- --
left door jamb . It shows the month and year of production and the
vehicle iden tifica tion n umber of your veh icle ( perfo ration) as well as
the Gross Vehicle Weight Rating (GVWR) and the Gross Axle Weight Rating (GAWR).
The high voltage warning label
is loca ted on the loc k carr ier .
The spark ignition system complies with the
Canadian standard ICES-002. •
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rating (GVWR), and the Gross Axle Weight
Ra ting (GAWR) for fron t and rear are listed on a st icker on the left
door jamb.
Th e Gross Vehicle Weight Rating includes the weight of the basic
vehicle plus f ull fue l tank, oil and coo la nt, plus max im um load, which
includes passenger we ight (150 lbs/68 kg per des ignated seating
position) a nd luggage weight .
Gross Axle Weight Rating
The Gross Axle Weight Rating is the maximum load that can be
applie d at each axle of the vehicle~& .
Vehicle capacity weight
The vehicle capacity weight (max. load) is liste d either o n the driver's
side B -pillar or inside the fuel f iller flap .
Roof weight
The maximum permiss ible roof weight is 165 lb (75 kg ). The roof
we igh t is ma de up o f the weig ht of the roof rack sys tem and the
we ight of the object being transported~
page 88, "Load ing the roof
rack" .
Safety first
& WARNING
• The actual Gross Axle Weight Rating at the front and rear axles
s hould not exceed the permis sible weights, and their combination
must not exceed the Gross Vehicle We ight Rating.
• Exceeding permi ssible weight rating s can result in vehicle
damage, accidents and personal injury .
0 Note
• The vehicle capac ity we ight figu res apply when the load is distrib­
uted evenly i n the vehicle (passengers and luggage). When trans ­
porti ng a heavy load i n the l uggage compartment, ca rry the load as
near to the rear axle as possible so that the veh icle's handling is not
impa ired.
• Do not exceed the maximum permiss ible axle loads or the
maximum gross vehicle weig ht. Always remember that the vehicle's
hand ling will be affecte d by the extra load. Therefore, adjust your
speed a ccording ly .
• Always observe loca l reg ulations. •
Dimensions
The specifications refer to the basic mo de l. Differences may occur
depend ing on the model ty pe a nd options ordered, for exam ple, tir e
sizes .
0 Note
When d riving up steep ramps, on rough roads, over c urbs, etc . it is
impo rtan t to remember that some parts of yo ur vehicl e, s uch as
spoilers or ex haust system components, may be close to the ground.
B e careful not to d amage them .•
Do-it,yourself service Technical data

_________________________________________________ D_a_ t_ a __ B'I
- Reserve (of total capacity)
Windshield washer fluid container
Engine oil with filter change
Safety first ga
l/liters
qu arts/liters
q uarts/liters 1.8 / 7 .0
3.1 / 3 .0
4. 8 I 4.6
Do-it,yourself service
•
Technical data

____________________________________________ ...;C _o_ n_s ...;u_ m __ e_r_ I _n_ f...;o _r_ m..:....:...: a:.:. t..:...:..; io:..:.... n __ _
Consumer Information
Warranty coverages
Your Audi i s covered by the following warrantie s:
• New Vehicle Limited Warranty
• Limited Warranty Against Corrosion Perforation
• Emissions Control System Warranty
• Emissions Performance Warranty
• California Emissions Control Warranty (USA vehicles only)
• California Emissions Performance Warranty (USA vehicles only)
Detailed in forma tion reg ard ing yo ur war ran ties can be fo und in your
Warranty & Maintenance Booklet .•
Operating your vehicle outside the
U.S.A. or Canada
Government regulations in the United States and Canada req uire that
au tomobile s mee t sp eci fic emi ssio n regula tions and safety s tan­
dards . Therefore, vehicles b uilt for the U .S .A . and Canada d if f er from
vehicles sold in othe r countr ies .
If you plan to take your veh icle outs ide the con tinen tal lim its of the
United States o r Canada , there is the poss ibility that
• unle ade d fu els for veh icles wi th c atal ytic conve rter m ay no t be
available;
• fue l may have a conside rably lowe r octane rat ing. Im proper f ue l
may cause engine damage;
• serv ice may be inadeq uate due to lack of proper service facilities,
too ls o r testing eq uipment;
• replacemen t parts may not be read ily avai lab le .
Safety first
• N aviga tion syst ems for ve hicles built fo r th e U .S.A . and Canada
will not necessar ily work in Europe, and may not work in other coun ­
tr ies o utside of North America.
Aud i cannot be responsible for mechanical damage that could
result from inadequate fuel, service o r parts availability .
0 Note
Audi cannot be responsible for mech anical dam age t hat cou ld resu lt
from inade quate fue l, se rvice o r parts ava ilab ility .•
Audi Service Repair Manuals and
Literature
Audi Off icial Factory Service Manuals and Literature are published as
soon as possible after model i ntroduct ion . Se rvice manuals and liter­
a tu re are avai lab le to order from t he Aud i Techni cal Lite ratur e
O rd eri ng Center at:
www.audi .techliterature.com •
Maintenance
General
Your vehicle has been des igned to help keep main tenance req uire ­
me nts to a min im um .
However, a certain amount of regular maintenance is st ill necessary
t o assure your ve hicle 's s afe ty, econ omy an d re lia bil it y.
For detailed vehicle maintena nce cons ult your Warranty
& Ma inte -
nance book let.
9J,,,
Do-it,yourself service Technical data

____________________________________________ _::C :.:o::.:...: n:..:s =..=u::.. m :....:.:..:: e:..:.r...: I ~n:..:...'.. f.::o ~r...:. m~ a~ t~ io~ n'..- __
& WARNING (co ntinued )
been remo ved. The radiator fan switches on automatically when
the coolant reache s a certain temperature and will continue to run
until the coolant temperatu re drops.
• Always remove the ign ition key before anyone gets under the
vehicle.
• Alway s support your v ehicle w ith safety stands if it i s nece ssary
to work underneath the vehicle. The jack supplied with the vehicle
is not adequate for th is purpose and could collapse causing
serious personal injury.
• If you must work underneath the vehicle with the wheels on
the ground, always make sure the vehicle is on level ground , that
the wheels are always securely blocked and that the engine cannot be started.
• Always make sure the transmi ssion selector lever (automatic
transmission) is in "P" (Park position ) (automatic transmission)
or Neutral (manual transmission) and the hand brake is firmly
applied.
'i> For the sake of the environment
• Chang ing the engine settings will adversely affect emiss ion levels.
Thi s is detr imenta l to the environme nt and increases fue l co nsump ­
tion .
• Alw ays obse rve enviro nmen tal regula tion s when dis pos ing of o ld
eng ine oil, used brake fl uid, d irty engine coo lant, spent batter ies or
wo rn out t ires .
• Undeployed a irbag modules and pretensione rs m ight be classi fied
a s Pe rchlo ra te Ma ter ia l -s pec ia l han dlin g m ay apply , see
www.dtsc.ca.gov/hazardouswaste/perchlorate. When the vehicle or
part s of th e re st ra int system i ncludi ng air bag modu les s afe ty belts
with pretens ioners are scrapped, all applicable laws and regulat ions
must be observe d. Yo ur a uthor ized Au di dealer is f amiliar wi th these
requirements and we recommend that you have your dealer perform
this service for yo u.•
Safety first
Additional accessories,
modifications and parts
replacement
Additional accessories and parts
replacement
Always co nsult an autho riz ed Audi d ealer bef ore
p urchasing acces sories.
Yo ur vehicle incorporates the latest safety design feat ures ens uring a
high standard of active and pass ive safety .
Th is safety could be compromised by non-approved changes to the
veh icle . F o r th is reaso n, if p arts have to be rep la ce d , ple ase obse rve
the following points when installing addit ional accessories:
Approved Audi accessories an d genuine A udi parts are avai lable from
au thori zed Aud i dea le rs .
These dea lers a lso have the necessary facilities, tools and tra ined
specialists to i nstall t he pa rts and ac cesso ries properly.
& WARNING
Using the wrong spare parts non-approved accessories can cause
damage to the vehicle and serious per sonal injury.
• Use only accessories expressly approved by Audi and genuine
Audi spare parts
• These parts and accessories have been specially designed to be
used on your vehicle.
• Never install accessories such as telephone cradles or beverage
holder s on airbag covers or within the airbag deployment zones .
Doing so will increase the risk of injury if airbags are triggered in
an accident!
• Before you check anything
in the engine compartment, always
read and heed all WARNINGS~
page 218. .,
Do-it,yourself service Technical data

______________________________________________ C _o_ n _ s_u_ m_ e_r_ I_n _f_ o_ r_m _ a_t_ i_ o _ n __ _
Declaration of Compliance,
Telecommunications and Electronic
Systems
Radio Frequency Devices and Radiocommunication
Equipment User Manual Notice.
Th e man ufa cture r is no t responsible for any rad io or TV in terference
caused by unauthorized modificat ions to this equipmen t.
Devices
The fo llowing devices each comply with FCC Part 15.19, FCC Part
15.2 1 an d RSS-Gen Issue
1:
• Cell phone package
• E lectronic immobilizer
• Homelink ® universal remote control
• Remote control key
• T ire pressure monitoring system"
FCC P art 1 5.19
This dev ice complies with part 15 of t he FCC Rules . Operation is
subject to the following two conditions:
( 1 ) T his device may not cause harmful interference, and
( 2 ) t his devi ce must accept any inte rfe rence rece ived, including inte r­
ference that may cause undesired operation.
FCC Part 15 .21
CAU TION:
Changes or mod ifications not express ly app roved by the party
respons ible for compliance could void the user 's authori ty to operate
the equipment.
RSS-Gen I ssue 1
Operation is subjec t to t he follow ing two conditions:
(1) this device may not cause interference, and
Safety first
(2) this device must accept any interference, including interference
t ha t may cause undesired opera tion of the device. •
Do-it,yourself service Technical data