2011 AUDI S3 technical data

What do I do now? Ill
------------------
Applies to veh icles : w ith ca p-covered wheel bolts
Wheels w ith cap -covered wheel bolts
The cops must be removed first from the wheel bolts
before the bolts con be unscrewed .
Removing
Fig. 186 Wheel
change: removing the
wheel bolt caps
-Push the plastic clip provided with the on board tool kit
down over the wheel bolt cap until it engages.
- Pull on the properly engaged
plastic clip to extract the cap
=> fig . 186.
Refitting
- Place the caps over the wheel bolts and push them back in.
The caps are there to protect and keep the wheel bolts clean. •
Vehicle OP-eration
Applies to veh icles : w ith ant i-theft wheel bolts
Anti-theft wheel bolts
To tighten or untighten the anti-the~ wheel bolts you
must use a special adopter .
....
(
..
V" Fig. 187 Anti-theft
wheel bolt with cap
and adapter
-Remove the cap* => fig . 187 @using the plastic clip
found in the vehicle tool kit .
- Insert the adapter ® as far as it will go into the anti-theft
wheel
(D bolt .
- Push the socket wrench over the adapter ®·
- Loosen or tighten the wheel bolt=> page 276.
To remove the cap* @, make sure the plastic cl ip is pushed in as far
in as possible until it lines up with the edge of the cap.
We recommend you keep the whee l bolt adapter in the tool kit.
The
code number o f the wheel bolt lock is stamped on the fron t side
of the adapter. You will need this number in order to get a replace­
ment from your authorized Audi dealer .
[I] Tips
Write down the code number and keep it in safe place . Do not keep it
i n the vehicle. •
Vehicle care Do-it-yourself service iTechnical data

_____________________________________________ W __ h_a _ t_ d_o_ I_ d _ o_ n_o_ w_ ? _ ___.fl'I
F ig. 190 Close -u p :
pro per po sit io ning of
lifting ja ck
- Activate t he parking brake so the vehicle wi ll not ro ll unin ­
tentionally .
- S hift into 1st gear on vehicles wit h manua l tra nsmiss ion,
o r mov e the selector lever to the P position on vehicles
with automatic transmissio n.
- Position t he jack be low the door sill under the mounting
point that is closest to the whe el to be chang ed
~ page 276, fig . 189 .
- Turn the jack handle cloc kwise un til the jack arm just fits
underneath t he rib running along t he under body
~ &, .
- Align the jack so that the jack arm claw~ fig . 190 @fits
snugly a round the underbody rib an d the mova ble base
plate ® sits flat o n the groun d. T he base ® must be
vertical unde r th e lifting point @.
- W ind the jac k up fu rt h er u ntil the flat whee l co mes o ff the
groun d~ &, .
Recesses at the front and rear of the u nderbody rib mark the proper
mounting lo cat io ns for the jack =>
page 2 76, fig. 189. The re is only
one
designated jack mount ing point for each wheel. Do not apply the
j a ck anywhe re else:::::, &.
Vehicle OP-eration T
he jack shou ld be posi tioned appro ximately 6 in . (15 cm) behind the
front wheel or 10 i n. ( 25 cm) in fron t of t he rea r w heel.
An
un stable surface u nder the jack can cause the vehicle to slip off
the jack. Always provide a firm base for the jack on the grou nd .
If
necessary pla ce a st urdy boar d or sim ilar su ppo rt unde r the jack. On
hard , slippery surf aces (s uch as ti les) use a rubber mat or s imilar to
preven t the j ack from sli pping =>& .
& WARNING
• You or your passengers could be injured while changing a
wheel if you do not follow safety precautions:
-Mounting the jack under the vehicle at any other place than
indicated above may damage the vehicle or may result in
personal injuries.
- A soft o r unstable surface under the j ack may cause the
vehicle to slip off the ja ck . Alway s provide a firm base for the
jack on the ground.
If necessary, use a sturdy board under the
jack.
- On hard , slippery surface (such as tiles ) use a rubbe r mat or
similar to prevent the ja ck from slipping.
• To help prevent injury to yourself and your pa ssengers:
- Do not raise the vehicle until you are sure the j ack i s securely
engaged.
- Passengers must not remain
in the vehicle when it is ja cked
up.
- Make su re that passengers wait in a safe place away from the
vehicle and well away from the roadway and traffic.
- Make sure jack position is correct, adjust as necessary and
then continue to raise the jack. •
Vehicle care Do-it-yourself service iTechnical data

_____________________________________________ W __ h_a_ t_ d_o_ I_ d_o _ n_ o_ w _ ? __ _
• Pull the reve rsible b lade from the screwdriver before you use the
hexagon al so cke t in the handle to turn t he whee l bolts .
• When mounting tires with
unidirectional tread design make sure
t he t read pa ttern is po inte d the r ig ht way =:>
page 2 79.
• The wheel bo lts shou ld be clean and easy to turn. Check for dirt
and corrosion on the mat ing surfa ces of both the whee l and the hu b.
Remove all d irt from these s urfaces before remounting the whee l.•
Tires with unidirectional tread design
Tires with unidirectional tread design must be mounted
with their t read pattern pointed in the right direction .
Using a spare tire w ith a tread pattern intended for
u se in a specific direction
When using a spare tire w ith a tread pattern intended for use in a
spec ific direction, please note t he fo llow ing:
• The direct ion of rotation is marked by an arrow on the side of the
tire.
• If the spare tire has to be installed in the incorrect direction in the
event of a flat ti re, use the spare tire only temporari ly since the tire
wi ll not be able to achieve its optimum pe rformance characterist ics
with regard to aq uaplaning, noise and wear .
• We recommend that particular attention be paid to this fact
during wet wea ther and that you adj ust you r speed to match road
conditions .
• Rep lace t he flat tire w ith a new one and have it ins talled on your
vehicle as soon as poss ible to restore the handling advantages of a
properly pointed direction -dependent tire .•
Safety first
Notes on wheel change
Please read the information =:> page 257, "New tires and rep lacing
ti res and wheels" if yo u are go ing to use a sp are t ire wh ich is diffe rent
from the tires on your vehicle.
After you change a tire:
• Che ck the tire pres sure on the spare immediately after
mounting .
• Have the wh eel bolt tight ening t orque ch ecked with a torque
wrench a s soon as poss ible by your authorized Audi de aler or a qual ­
ified servi ce station.
• On steel and allo y wheel rim s, the wheel bolts are co rrectl y
tightened with a torque of 90 ft lb (1 20 Nm ).
• If you not ice while ch anging a tire that the wheel bolt s are
corroded and difficult to turn, then they should be r eplaced before
yo u che ck the tightening torque.
• Repla ce the flat tire with a new one and have it installed on your
vehicle a s soon a s po ssible . Remount the wheel c over.
Until then, drive with e xtra care and at reduced speed s.
& WARNING
• If you ar e going to equip your vehicle w ith tire s or rims which
differ from tho se which were factor y installed, then be sure t o
read the information =:>
page 257, "New tires and replacing ti re s
and wheels ".
• Alway s make sure the damaged wh eel or even a flat t ire and
the jack and tool kit a re properly secured in the lugg age compart­
ment and ar e not loo se in the pa ssenger compartm ent .
• In an accident or sudden maneuver th ey could fly forward ,
injur ing anyone in the vehicle .
• Alway s store damaged whee l, jack and t ools se cure ly in
luggage compartment. Otherwise, in an accident or sudde n
Vehicle care Do-it-yourself service Technical data

______________________________________________ F _u_s _e_ s_ a_ n_ d _ b _u_l_b _ s _ ___.fflll
Fuses and bulbs
Electrical fuses
Replacing fuses
A problem in the electrical system may be caused by a
blown fuse .
Fig. 193 Left cockpit:
f use pa nel cover
Fig. 19 4 Left s ide o f
engine compar tm ent:
' fuse cove r
Vehicle OP-eration
Fuse cov er on th e left end fac e of th e
instrum ent pan el
- Turn off the ignition and the affected electrical
consumers .
- Carefully pry the fuse cover off the instrument panel using the ignition key or a screwdriver=> fig. 193 .
- Check the following table to see which fuse belongs to the
consumer =>
page 282, "Fuse Location, Instrument Panel
left".
- Remove the clamp from the rear side of the fuse cover
=> fig. 193 .
- Remove the fuse using the clamp and replace the blown fuse with an identical new one .
- Firmly snap the cover back onto the instrument panel
face .
Fuse cover in engine compa rtment
- Turn off the ignition and the affected electrical
consumers.
- Check the following table to see which fuse belongs to the
consumer =>
page 284, "Fuse location, left side of engine
compartment" .
- Unlatch the fuse cover, push the two slides forward => fig. 194.
- Remove the clamp from the rear side of the fuse cover
=> fig. 193.
Vehicle care Do-it-yourself service iTechnical data

_______________________________________________ F_u _s_ e_ s_ a_ n_ d_ b_u _ l_ b _ s __ _
Equipment No. II Equipment
Amps
Manual headlight beam adjustment, automatic Diagnostic connector, rain sensor, air condition-
headlight beam adjustment, AFS control mod-
16 ing (control module), tire pressure monitor dis-10
1 ule, engine components, light switch (switch 10 play (control module)
-lig hti ng/i llum i nation), diagnosis socket 1 7 Ant i-theft alarm warning system 5
Automatic transmission, control module for CAN 18 Diagnose Starter 5
data transfer (gateway), electro-mechanical
19 All Whee l Drive 10 steering, shift gate automatic transmission, 2 10 engine relay, fuel tank control unit, engine con-22 Blower fan 40
trol unit, brakes control (ABS), Electronic Stabili-23 Driver's side power window, front 30 zation Program (ESP), Anti-Slip Regulation (ASR)
3 Airbag 5 24 Power outlet front 20
Air-conditioning (pressure sensor, air quality sen-25 Rear window defogge r 30
sor), button for Electronic Stabilization Program 26 Power outlet in luggage compartment 20
(ESP), Anti-Slip Regulation (ASR), tire pressure 27 Fuel tank control module, fuel pump 15
monitor display, oil level sensor, back-up light
28 Power window, rear 30 4 switch, front seat heating, parking aid, seat-s
occupancy recognition (on USA vehicles), garage 33 Sliding/pop-up roof 20
door opener, automatic mirror dimming, head-
Lumbar support
10 light assistant, heated windshield washer noz-
zles, air conditioning (control module)
3 7 Hea ted seats, front 20
--
5 AFS headlights (left side) 5 38 Passenger side power window, front 30
AFS headlights (right side) 5 39 Specia l function interface 5
9
Navigat ion system, radio system 15 40 Starter 40
digital radio, cell phone, TV equipment 7,5 Rear window wiper 15
11
Automatic mirror dimming, headlight assistant 10 Body control module 20
12 Central locking (front doors) 10 47 Ce ll phone package (VDA interface) 5
13
Central locking (rear doors) 10
A uto m atic c ircu it bre ake rs :
14 Electronic Stabilization Program (ESP) (control 10 The electric power w indows and the electric seat adjusters are
module), shift gate automatic transmission protected with circuit b reakers which reset automatically after the
1 5 Inter ior lights, read ing lights 10 circuit overload has been corrected . ...
Safety first Vehicle care Do-it-yourself service Technical data

_______________________________________________ F_u _s_ e_ s_ a_ n_ d_ b_u _ l_ b _ s __ _
No. Equipment
F2 7 Secondary a ir pump, preheating contro l module
F 29 Fuse assignment in the left-side instrument
panel (special equipment)
F30 Power supply relay termina l 15
Bulbs
Replacing light bulbs
Amps
40
so
so
For you r safety, we recommend that you have your autho ­
ri zed Audi dealer replace burned out bulbs for you.
It is becoming increasingly more and more difficu lt to rep lace vehicle
light bulbs since in many cases, ot her parts of the car must first be
removed before you are able to get to the bu lb. This app lies espec ially
to the l igh t bu lbs in the front of your car whi ch you can o nly rea ch
through the engine compartment .
Sheet metal and bu lb holders can have sharp edges that can ca use
serious cuts, and parts must be correctly taken apart and the n prop­
erly put back together to he lp prevent b reakage of parts and long
term damage from wate r that can enter housings that have not been
p roperly resealed.
For your safety, we recommend that you have you r authorized Audi
deale r replace any bu lbs fo r you, since your dealer has the proper
too ls, the cor rec t bu lbs and the expertise .
Gas dis charge lamp s (Xenon lights)* :
Due to the high electrical voltage, have the bulbs replaced by a qual­
ified technician. Headlights with Xe non light can be iden tified by the
high voltage sticker.
Safety first
•
& WARNING
C ontact with high-voltag e components of the electrica l system
and improper replacement of g as discharge (Xenon ) headlight
bulb s can caus e serious personal injury and death .
• Xenon bulb s are pres surized and can explode when b eing
c hanged .
• Changing Xenon lamp s requir es the special training , instruc ­
tions and equipment.
• Only an authori zed Audi dealer or oth er qualified workshop
should change the bulbs in ga s di scharge lamp s.
& WARNING
There are parts with sharp edge s on the openi ngs and on the bulb
holde rs that can cau se se rious cuts.
• If you are uncertain about what to do, ha ve the work
performed b y an auth orized Audi de aler or oth er qualified work­
s hop. Seriou s per sonal injur y m ay re sult from improperl y
p erformed w ork.
(I] Tips
• If you must replace the light bulbs yourself , a lways remember
that the engine compar tment of any vehicle is a hazardo us area to
work in. Always read and heed all WARNINGS=>
page 218, "E ngi ne
compa rtment" =>& .
• It is best to ask you r author ized Audi dealer whenever you need to
change a bu lb. •
Vehicle care Do-it-yourself service Technical data

_____________________________________________ E_ m_ e_r-= g ::.. e_ n_c-= y'- s_ i_t _u _a_ t_ i_ o _ n_ s __ fflll
& WARNING (co ntinued )
• Before you che ck anything in the engine compartment , alway s
r e ad and heed all WARNINGS =>
page 218, "Engi ne compart­
ment ".
0 Note
• App lying a higher vo ltage booster battery will cause expens ive
damage to sens itive e lec tro nic components, such as contro l units,
re lays, rad io, etc.
• Th ere must be no electrical contact between the veh icles as othe r­
wise current could a lready sta rt to flow as soon as the posit ive(+)
term inals are con nected.
• Improperly connecte d jumper cables can cause substantial
damage to the e lectr ica l system of the vehicle .
[I) Tips
• The discharged batte ry mu st be properly co nne cted to the
vehicle's elect rical system. •
General information of starting
assistance
Please observe that the procedure descr ibed below for connect ing
jumpe r cab les is intended to p rovide a ju mp s tart for your ve hicl e.
Make sure t hat the co nnected clamps have suff ic ient
metal contact.
Sta rt assistance differs for vehicles w ith a 4-cylinde r engine:
=> page 288, "Use of jumper cables"
Safety first
& WARNING
Improper handling of the jumper cables can lead to an explosion
of the battery and severe injurie s. To reduce the ri sk of injury, note
the following:
• The section s of the terminal clamps that are not insul ated
must not touch each other. In addition, the cable clamped to the
battery' s po sitive terminal must not come in contact with electri­
cally connected parts of the veh icle -danger of short circu it!
• Route the jumper cable so that it cannot catch in any rotating
parts in the engine compartment .
• Do not bend over the batteries -danger of chemical burns!
• The battery cell locking screws must be tightened securely.
• Keep ignition source s (open flame , burning cigarettes, etc.)
away from the batteries -danger of explosion!
• Do not clamp the minus cable to parts of the fuel system or the
brake lines.
0 Note
If you prov ide sta rt assistance for others with your vehi cle, you shou ld
not clamp the minus cable( -) to the negative te rm inal of the
discharged batte ry =>
page 288, fig. 19 7 © but to a solid metal part
sc rewed firm ly to the eng ine b lock, or to the e ng ine block itse lf . In
case of an inadequately venti lated battery o f the veh icle receiving
powe r, the re is a dange r of explosi on du e to detonat ing gas! •
Vehicle care Do-it-yourself service Technical data

_____________________________________________ E_ m_ e_r-= g ::.. e_ n_c-= y'- s_ i_t _u _a_ t_ i_ o _ n_ s __ _
13. Disconnect the cable w hile the engine is runn ing exactly
in
reverse or der to t hat described in~ page 288,
"Connec ting/discon nect ing the jumper cable" . When
doi ng so , ma ke sure that t he cab le ca nnot contact rotat ing
eng ine parts .
14 . T urn the h eater bl ower a nd th e re ar w indow hea tin g off
a gain.
Th e bat tery is ven ted to the o utsi de to p reven t ga ses from en ter ing
the ve hicle interior .
M ake s ure that the jumpe r clamps a re well connected w ith their
metal parts in full contact with t he battery termi na ls .
& WARNING
To avoid serious personal injury and damage to the vehicle, heed
all warnings and instructions of the jumper cable manufacturer . If
in doubt, call for road service.
• Jumper cable s mu st be long enough so that the vehicles do not
touch.
• When connecting jumper cable s, make sure that they cannot
get caught in any moving parts in the engine compartment.
• Before you check anything in the engine compartment, always
read and heed all WARNINGS=>
page 218, "Engine compart­
ment ".
0 Note
Im pro perly con ne cte d jum per c abl es c an dam age or destroy the
generator.
• Do not use the ba ttery nega tive term inal for jum p star ting or a
ma lf u nction co uld occ ur in the vehicle electrica l system .
• Always co nnect POSITIV E(+) to POSI TIVE( +), a nd NEGATIVE( -)
to N EGATIVE{ -) termina l.
Safety first
• Check that all screw p lugs on the battery cells are screwed in
fir mly . If no t, tig hten plugs pr ior to connectin g clamp o n negative
battery term inal.
• P lease note that the pr ocedur e fo r connecting a jumper cable as
described above app lies specifically to the case of your vehicle being
jum p st ar te d . When you are giving a jump start to anot her vehi cle, do
not conn ect the m in u s (-) cable to t he minus( -) term inal on the
discharged battery ©=>
page 288, fig. 197 . In stea d, sec urely
connect the mi nus( -) cable to either a massive metal component
that is f irm ly bo lte d to t he eng ine block or to the engine bloc k itse lf .
If the battery that i s bei ng charged does not ven t to t he ou tside,
escaping battery gas could ignite and explode! •
Emergency towing with
commercial tow truck
c;eneral hints
Your Audi requires s pecial h andling for to win g.
The follow ing informat ion is to be used by commercial tow truck
oper ator s w ho know how to oper ate th eir equipmen t sa fe ly.
• Never tow your Audi, towing will cause damage to the engine
and transmission.
• Never wrap the safety chains or winch cables around the brake
lines.
• To prevent unnecessary damage, your Audi must be transported
with a car carrier (flat bed truck ).
• To load the vehicle on to the flat bed, use the towing loop found
in the vehicle tools and attach to the front or rear anchorage
=> page 290 and=> page 290 . ..
Vehicle care Do-it-yourself service Technical data