2011 AUDI Q7 service

& WARNING (continued)
• The Panoramic sliding sunroof will continue to operate until
the ignition key has been removed and one of the front doors has
been opened .•
A pp lies to vehicles : w ith Panoram ic sl iding sunroof
Mechanical emergency closing for front
roof segment (Step 1)
The Panoramic sliding sunroof can be closed manually in
an emergency.
Fig. 52 Section of
front headliner: Removing cover
Fig. 53 Section of
front headliner:
Removing the cover for
the light unit
Removal of the light unit requires some dexterity.
Contro ls a nd e quip ­
m en t Vehicle
OP-eration
Opening and closing
-Open the compartment.
- Pull the chrome strip down carefully, along with the
center cover~ fig. 52 -Arrow-.
- Pull the cover for the light unit down carefully~ fig. 53
-Arrows-. •
Applies to v ehicles: w ith Pano ramic slid ing sun roof
Mechanical emergency closing for front
roof segment (Step 2)
I 0
'-:'~
-~ •-- 1 I • • •
( -
I
I I
Fig. 54 Section of
front headliner:
Removing light unit
Fig. 55 Section of
front headliner: Crank
for emergency opera­
tion
- Take the screwdriver from the vehicle tool kit~ page 340 . .,_
Vehicle care Do-it-yourselt service iTechnical data

Clear vision
Lights
Switching the headlights on and off -'t!-
In the "AUTO" position, a light sensor automatically
swit ches the head- and tai llights on and off in response
to light condition s.
F ig . 56 Inst rum ent
pan el: li ght swit ch
The light switch must not be overturned past the stops in
either direction .
Switching on automatic headlight control
-Turn th e light swi tch to AUTO ::::, fig. 56.
Switching on the side marker lights
-Tur n the light sw itch to 300~.
Switching on the headlights and high beam
- Turn the light swi tch to ~D.
- Push the high beam lever forward towards the instrume nt
panel=>
page 71.
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Switching off the lights
-Turn the lig ht swit ch to 0.
Clear vision
The headligh ts only work when the ignition is switched on. Whi le
sta rting the engine or when switchi ng off the ignition, the headlights
will go off and o nly the s ide marker lights will be on.
After start ing t he engine, the headlights are automatically adjusted*
to the load and a ng le of the vehicle (fo r example, during acceleration,
braking) . This prevents oncoming traffic from experiencing unneces­
sary head light glare from your head lig hts.
If the system is not operati ng p roperly, a warning symbol in t he Auto­
Check Control is displayed=>
page 39.
With the side marker lights o r headlights switched on, the symbol
next to the light switch illuminates
coo: .
Daytime running lights
• USA models: The daytime runn ing lights w ill come o n automati­
ca lly when the ign ition is turned on and the light switch => fig. 56 is
in the
O position or the AUTO position (only i n daylight conditions) .
Th e
Daytime running light s function can be tu rned on and off in the
MMI menu
Exterior lighting=> page 68.
• Canada model s: The d ay time r unning ligh ts w ill come on a uto­
matically when the ig nitio n is turned on and the light switch=> fig. 56
is in the
O pos itio n or the AUTO position (on ly in daylight conditions)
=> & .
Automatic headlight control
In the switch pos ition AUTO t h e automatic headlight control is
tu rned on. The low beams and tail lights a re turned on au tomatically
throug h a light sensor as soon as ambient br ightness (e .g . when
driving into a tunnel) falls be low a va lue preset at the factory . When
amb ient b rightness increases again, the low beams are turned off
again automatically =>& . ..,_
Vehicle care Do-it-yourselt service iTechnical data

Front fog Lights }O
Fig. 57 Instru men t
panel : light s witch
The light switch must not be overturn ed past the stops in
either direction.
Switching on the front fog lights }D
Turn the light switch to :oo:: or to io .
- Pull the light switch to the first stop (D.
When the front fog lights are on, the symbo l tO next to the light
switch will illum inate .
[I] Tips
With the sw itch in AUTO front fog lights and rear fog lights cannot be
turned on in addition .•
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Rear fog Lights 0$
Clear vision
Fi g. 58 Inst rume nt
p ane l: li ght s witch
The light switch must not be ove rturned past the stops in
eithe r direct ion .
- Turn the light switch to
:oo:: or to io.
- Pull the light switch to the second stop @.
When the rear fog lights are on, both the tO and ,._ symbols next to
the l ight sw itch will illumina te.
0 Note
T he rear fog lights can distract drivers behind you, so, they sho uld be
turned on
only in cond it ions of very poor visibility . Always observe
loca l reg ulations when using the rear fog lights.
[I] Tips
With the switch in AU TO front fog lights and rea r fog lights cannot be
turned on in addition .•
Vehicle care Do-it-yourselt service Technical data

(]] Tips
You shou ld turn on t he emergency flashers when :
• you are the last vehicle stand ing in a traffic jam so that any other
vehicles com ing can see you , or w hen
• your vehicle has broken down o r yo u are in an eme rgency s itua ­
tion, or when
• your vehicle is be ing towed by a tow tr uck o r if you are tow ing
another vehicle behind you .•
Turn signal ¢¢ and high beam ~D Lever
The lever on the le~ side of the s teering column is used to
operate the turn signals and the high beam as well a s the
headlight flasher .
-"' M
-w ... m
Fig. 61 Tu rn signal
and hi gh bea m l ever
The tu rn s ignal and high beam lever has the follow ing func­
tions:
Turn signals ¢ ¢
- Lift the lever up all the way~ fig. 61 (D to use the right
turn signals, or push the lever down all the way@ to use
the left turn signals.
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Clear vision
Auto -blink
- Move the lever (up or down) just to the point of resistance
to use the turn signa ls for as long as you need them, for
examp le when chang ing lanes.
- M ove the lever (up or down) just to the poi nt of res istance
and t hen re lease it right away to make the turn signa ls
blink
three times . You can use this feature for examp le
w hen changing lanes on highways.
High beam ~D
- Push the lever forward @ to switch on the high beam .
- Pull the lever back towa rds you to switc h off the high
beam .
Headlight flasher ~D
Pull the lever toward the steering wheel© to use the
head light flasher .
Notes on these features
• The turn signals only work with the ignition t urned on. The indi­
cato r lights ¢ or¢ in the instrument cluster=>
page 14 a lso blink.
• After you have t urned a co rner, the tu rn signal switches off auto ­
matically .
• Th e
high beam works only when the hea dlights are o n. Th e ind i­
ca tor light
aD in the instrumen t cluster illuminates when the high
beams are on.
• The
headligh t flasher works only as long as you ho ld the lever -
even if there are no l igh ts turned o n. Th e indic ator lig ht
aD in the
instrument clus ter illuminates when you use the headlight flasher. .,,_
Vehicle care Do-it-yourselt service iTechnical data

r ,:le,
Fig. 64 Headliner :
Third row reading light
-Press one of the switches ~ to turn the right or left
reading light on or off~
page 72, fig . 63.
For vehicles with third row seating*, the l uggage compartment light
can be switched on and off with the button~ and used as a reading
light => fig. 64. The rear lid has to be closed.
The lights in the luggage compartment and in the rear lid switch on
and off automatically when the lid is opened and closed.
[ i ) Tips
If the rear lid remain s open longer than 10 minutes, the luggage
compartment lights turn off automatically to prevent the vehicle
battery from discharging. •
Applies to veh icles: with ambience light ing
Ambience Lighting
The ambience lighting can be adjusted in the MMI.
-Select: Function button I CAR]> Systems *> Ambience
lighting .
When the vehicle is unlocked, the standard lighting turns on auto­
matically and dims after approx. 2 minutes, and when the ignition is
turned on it switches off immediately.
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Clear vision
The following interior lighting is controlled through
Ambience lighting:
• Front footwell
• Rear footwe ll
• Front door panel
• Rear door pane l•
Vision
Sun visors
Using the sun visors makes driving safer.
Sun visors
Fig. 65 Passenge r
side: Sun v isor
The forward visor of the dua l sun v isor can be pulled out of its bracket
in the center of the vehicle and swung towards the door. The sun visor
can be extended after it is swung towards the door=> fig. 65.
Vanity mirror
The vanity mirrors on the sun visors are covered. When the cover is
ra ised, the mirror lighting switches on automatically . It turns off
when the lid is closed or the visor is fo lded up aga in.•
Vehicle care Do-it-yourselt service iTechnical data

As soon as the reverse gear is engaged and the front w ipers are
turned on and operat ing at the same time, the rear wiper a lso tu rns
on automatically.
& WARNING
Wiper bla des ar e c rucia l for safe driv ing ! Onl y in good c ond ition
are the y able to cl ear the wi ndow s pr operl y to prov ide unr estricted
vi sib ilit y. W orn or fra yed wi per bl ad es are a safety hazard !
=> page 78, "Repla cing wind shi eld wiper blade s"
0 Note
In freezing or near freezing conditions:
• Always check that the w iper blades are not frozen to the glass
befo re you turn the wiper on. Loosen a w iper b lade w hich is frozen in
place before operat ing the w iper to prevent damage to the wiper
blade or the wiper motor.
• Do not use the wiper to clear a frosted window. Using the wipers
as a convenient ice scraper will dest roy the w iper blades. •
Applies to veh icles: with head light washer sys tem
Headlight washer system
The headlight washer system cleans the headlights.
- Operate the windsh ie ld wiper/washer system:::::, page 74,
fig. 68 ® with the headlights turned on by ho lding the
lever for longer than one second .
The washer jets extend forward o ut of the front bumper dr iven by
water pressure to spray the front headlights w ith water .
You shou ld inspect the headlights regularly (for example when refu­
eling) and clean off any solid dirt o r insects from the lenses .
To ensure the system works properly in winter, keep the washer jets
free of snow and remove any ic e using a de-ic ing sp ray .•
Controls and equip ­
ment Safety first
Clear v
ision
Service position
The wiper blades can only be changed in the service posi­
tion.
- I f the wiper blades are not frozen to the windshie ld, bring
the windsh ield wiper l ever to the basic position ®
=:, page 74, fig. 68.
- Select: Function button
I CAR]> System s*> Windshield
wipers > Serv ice positio n.
• On -chang ing the windsh ield wiper blades can only be done if you
bring the wiper arms to the service position. You will also avoid paint
damage to the hood when working on the wipers in this position .
• Off -the w indshield wipers are moved to their initial position
again.
0 Note
Never maneuver yo ur vehicle w ith the front windshie ld wiper arms
ra ised since they will automatically be moved back to their basic posi­
tion above a speed of 3 mph (6 km/h) and can scratch the hood .
[ i ] Tips
• You can also use the service posi tion, for example, if you want to
protect the windshield from icing by using a cover .
• T he serv ice position automa tically switches to
Off when you
operate the windsh ield w iper lever, or speed exceeds 3 mph (6
km/h) .•
Vehicle care Technical data

Clear vision
Replacing windshield wiper blades
Wiper blades in good condition help keep the windshield
clear .
@
Removing a wiper blade
Fig. 7 0 R em ov in g the
wi pe r bla des
Fi g. 7 1 In stallin g
w ipe r b la de s
- Bring the windshield wipers to the service position
~page 77.
- Lift the wiper arm away from the windshield.
- Squeeze t he p lastic bracket on the w indshield wiper arm
together on both sides©~ fig . 70.
- Turn the wiper b lade away from the wiper arm . -
Lift the wi per blade off in the direction of th e arrow @.
Installing wiper blade
- Place the new wiper blade in the retainer on the wiper arm
© ~fig. 71.
Swing t he wiper blade in the direct ion of the arrow @
against the wiper arm.
- Squeeze the co rrugatio n on the w iper until you hear the
bracket click in the wiper ar m.
- Place the w iper arm back again st t he wi ndshi eld .
Clean yo ur wipe r blades regula rly with a w indshield washer solution
to prevent streak ing . If the blades are very dirty , for example with
insec ts, carefully clean t he b lades w ith a sponge o r a soft bru sh .
If the w iper blades begin to streak the wi nds hield, this could be
caused by residue lef t on t he windsh ie ld by au toma tic c ar washes .
Fill the windsh ield washer container w ith a special solut ion avai lable
at your authorized Audi dealer to remove the residue.
& WARNING
Be sure to inspe ct the condition of your wiper blades regularly. See
your author ized Audi dealer for repla cement blade s.
0 Note
• The windshield w iper blades must only be replaced when in the
service position =>
page 77! Otherw ise, you risk damaging the paint
on t he hood or the windsh ield w iper motor.
• T o help prevent damage to the wipe r system, always loosen
blades which are frozen to the winds hield before operat ing wipers . .._

• To help prevent damage to w iper blades, do not use gasoline,
kerosene, pa int thinner, or o ther solven ts on or near the w ipe r
blades.
• T o help prevent damage to the wiper a rms or othe r compo nents,
do not attempt to move the wipers by hand.
W Tips
Commercial hot waxes applied by automat ic car washes affect the
cleanability of the windshield. •
Changing the rear wiper blade
Removing the wiper blade
Fig. 7 2 R ear wind ow
wi per Det achi ng the
r e ar wiper blad e
- Fold the windsh ie ld wi per arm away from the glass .
- Grasp the upp er end of the wiper arm with one hand an d
the meta l clamp on the w iper blade w it h the o ther
=> fig. 72 .
- Hold the wiper arm in t he direction of the arrow@ and
pul l the wiper blade out of th e holder only in the dir ect ion
of th e arr ow @ .
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Clear vision
Attaching the wiper blade
- Adjust t he wiper blade in the ho lder.
- Hold the upper end of the wiper arm with one hand .
- Press the wiper b lade into t he holde r with you r other
hand .
- Fold the wi per arm back onto th e windshield.
& WARNING
• To avoid streak s, you should clean the windshield wiper bl ade s
regularl y with window cleane r. Fo r heavy soili ng, for example,
inse ct s, the wiper blades can a lso be cleaned with a sponge or a
cloth .
• For safety reasons , th e wind shield wiper blades shou ld be
replaced on ce o r tw ice a ye ar. •
Mirrors
Manual anti-glare adjustment
Standard setting
- Move the small lever (located on t he bottom edge of the
mir ror) to t he front.
Anti-glare setting
- Move the small lever (located on the bottom edge of the
m irror) to the rear .•
Vehicle care Do-it-yourselt service iTechnical data