2011 AUDI A5 COUPE jack points

_____________________________________________ W __ h....:a_ t ___ d_o ___ I_ d_o :.....:.. n.:..o::.. w.:....:.. ?------J-
& WARNING (continued)
• Do not loosen the wheel bolts more than one turn before you
raise the vehicle with the jack. -You risk an injury.
(I) Tips
• Never use the hexagonal socket in the handle of the screwdriver to
loosen o r tighten the wheel bolts .
• If a wheel bolt is very tight, you may find it easier to loosen by
carefully pushing down on the end of th e wheel bolt wrench with
one
foot only .
As you do so, hold on to the car to keep your balance and
take ca re not to slip .•
Raising the vehicle
The vehicle must be li~ed with the jack first before the
wheel can be removed.
•
Fig. 224 Changing a
wheel: mounting
points for the jack
Vehicle OP-eration
Fig. 225 Close-up:
proper positioning of
jack
The location of the jack point is indicated by an indentation
on the underside of the vehicle=> fig. 224.
- Activate the
parking brake to prevent the vehicle from
rolling unintentionally.
- Shift into
1st gear on vehicles with manual transmission
or move the selector lever to the
P position on vehicles
with automatic transmission*.
- Find the
lifting point in the sill that is closest to the faulty
wheel => fig. 224.
Turn the handwheel on the
vehicle jack until the jaw
=> fig . 225 @ covers the
notch on the vehicle.
- Align the vehicle jack so the jaw@ covers the notch and
the base plate @ is flat on the floor. The base plate @
must be
vertical under the lifting point@.
- Install the rod on the vehicle jack: Insert the rod into the
opening on the handwheel. Turn the rod left or right to
secure it.
- Continue raising the jack with the rod until the wheel lifts
off the ground slightly. ..,_
Vehicle care Do-it-yourself service iTechnical data

lffl!l.,___W __ h_a_ t_ d_ o_ I_ d_o_ n_ o_w _ ? _____________________________________________ _
Only position the veh icle jack at the designated points=> page 319,
fig . 224 . Th ere i s ex act ly
one loc ation for each whee l. Do not position
the jac k in any othe r locations .
Soft ground under the jack can cause the vehicle to slip
off the jack.
Alw ays p lac e the j ack on firm ground . U se a fla t, stab le s uppor t if
necessary. Use a non -s li p surface s uch as a ru bber mat on a slippery
surface such as ti le.
& WARNING
• You or your passengers could be injured while changing a
wheel if you do not follow these safety precautions :
- Positioning the jack under the vehicle at any other place than
those indicated above may damage the vehicle or may result in personal injuries.
- A soft or unstable surface under the jack may cause the
vehicle to slip
off the jack. Always provide a firm base for the
jack on the ground.
If necessary, use a sturdy board under the
jack.
- On hard, slippery surface (such as tiles) use a rubber mat or
similar to prevent the jack from slipping.
• To help prevent injury to yourself and your passengers: -Do not raise the vehicle until you are sure the jack is securely
engaged.
- Passengers must not remain in the vehicle when it is jacked
up .
- Make sure that passengers wait in a safe place away from the
vehicle and well away from the road and traffic.
- Make sure jack position is correct, adjust as necessary and
then continue to raise the jack. •
Taking the wheel off/installing the spare
tire
Follow these instr u ction s step- by -s tep for chan ging th e
w heel .
Fig. 226 Changing a
wheel : using the
s crewdriver handle
( with the blade
removed ) to turn the
bolts
Fig. 227 Changing a
whee l: alignment pin
in side the top hole
Aft er yo u have L oosened a ll w hee l bolts and r aise d the v ehicle
off th e ground, remo ve and rep lace t he whe el as fo llows :
Removing the wheel
- Remove the top most w hee l b olt comp letely with the
hexagonal socket in the screwd river handl e (vehicle too l
kit )
~ fig. 2 26 and set i t aside on a clean surf ace . .._

Emergency situations --------------=---:.--___.EWI
-Attach the winch hook to the rear tow line eye previously
installed .
[I] Tips
Check carefu lly to make sure the hook -up is secure befo re moving the
car up the flatbed truck ramp. •
Lifting vehicle
Lifting with workshop hoist and with floor
jack
The vehicle may only be lifted at the lifting points illus­
tr ated.
Fig . 23 8 F ront lifting
p oi nt
Vehicle OP-eration
Fig. 239 R ear li fting
p oint
- Read a nd hee d W AR NIN G ~ & .
- Lo cat e lift in g points ~ fig . 2 38 and ~ fig. 239.
- Adjust lifting arms o f worksho p hoist or floo r jac k to
ma tc h vehicle li fting poin ts.
- Inse rt a rub ber pad between the floor jack/wor ks h op hoist
an d the liftin g points.
If you must lift your vehicle with a floo r jack to work underneath,
be sure the vehicle is safely supported on stand s intended for this
purpose.
Front Lifting point
T he lifting point is located on the floor pan re inforcement about at
the same level as the j ack mou nting poin t::> fig. 23 8.
Do not lift the
vehicle at the vertical sill reinforcement.
Rear lifting point
The lifting point is located on the vertical reinforcement of the lower
s ill for the onboar d jack ::> fig. 239.
Lifting with vehicle jack
Refe r to::> page 319 .
Vehicle care Do-it-yourself service iTechnical data

lffll.___E_ m_ e_ r-' g=- e_n_ c=-y _ s_it _ u _ a_t_ i_ o _ n_ s ______________________________________________ _
in. WARNING
• To reduce the risk of serious injury and vehicle damage.
-Always lift the vehicle only at the special workshop hoist and
floor jack lift points illustrated
=> page 333, fig. 238 and
=> page 333, fig. 239.
- Failure to lift the vehicle at these points could cause the
vehicle to tilt or fall from a lift if there is a change in vehicle
weight distribution and balance. This might happen, for
example, when heavy components such as the engine block or
transmission are removed.
• When removing heavy components like these, anchor vehicle
to hoist or add corresponding weights to maintain the center of
gravity. Otherwise, the vehicle might tilt or slip off the hoist,
causing serious personal injury.
0 Note
• Be aware of the following points before lifting the vehicle :
-The vehicle should never be lifted or jacked up from under­
neath the engine oil pan, the transmission housing, the front or
rear axle or the body side members. This could lead to serious
damage.
- To avoid damage to the underbody or chassis frame, a rubber
pad must be inserted between the floor jack and the lift points.
- Before driving over a workshop hoist, check that the vehicle
weight does not exceed the permissible lifting capacity of the hoist.
- Before driving over a workshop hoist, ensure that there is sufficient clearance between the hoist and low parts of the
vehicle. •

__ _:C:::.::: o:..:n..: s :::.: u:.:m..:..:. e=.:.. r...: l:.: n:..:..:. f..:o :.:r~ m..:..:. a=--: t:.:.i o =-=- "-=- ---------------------------------------------
& WA RNING (conti nu ed )
• Always rem ove the ignition key before anyone get s under the
vehicle .
• Always support your vehicle with safety stands if it i s nece ssary
to work underneath the vehicl e. Th e jack supp lied with the vehicle
is not adequate for thi s purpose and could collap se causing
seriou s personal injury .
• If you must work underneath the vehicle with the wheels on
the ground, a lway s make sure the vehicle is on level ground, that
the wheels are alway s securely blocked and that the engine cannot
be started .
• Always make sure the transmi ssion selector lever (automatic
transmission ) is in "P " (Park po sition) or Neutral (manual tran s­
mission) and the park brake is firmly applied .
For the sake of the environment
• Changing the engine settings will adversely affect emission levels .
Thi s is det rimenta l to the envi ronme nt and increases fue l co nsump­
tion.
• Always observe enviro nmental regulations when disposing of old
engine oi l, used brake fl uid, dirty engine coo lant, spent batteries or
worn out t ires.
• Undep loyed a irbag modules an d pretens ioners migh t be classified
as Pe rchlorate Mater ia l -spec ial handling may apply, see
www.dtsc.ca.gov/hazardouswaste/perchlorate . When the vehicle or
parts of the rest raint system includ ing a irbag modu les safety belts
w ith pretens ioners are scrapped, all applicable laws and regulat ions
must be obse rved. Yo ur author ized Aud i dealer is f amiliar wi th t hese
req uirements and we recommend that you have your dealer perform
t his se rvi ce f or yo u.•
Additional accessories,
modifications and parts
replacement
Additional accessories and parts
replacement
A lways consult an autho riz ed Au di dealer bef ore
purchasing access ories.
Your vehicle incorporates the latest safety desig n featu res ens uring a
hig h standard of active and passive safety .
Th is safety co uld be compromised by non-app roved changes to the
vehicle. Fo r this reaso n, if par ts have to be replaced, p lease observe
the following points when installing addit ional accessories :
Approved Audi accessories and genuine Aud i parts are available from
author ized Aud i dea lers.
T hese dea lers a lso have the necessary fac ilities, tools and tra ined
specialists to i nstall the parts and a ccessor ies p roperly.
& WARNING
Using the wrong spare parts or u sing non-approved acces sorie s
can cause damage to the vehicle and serious personal injury.
• Use only accessories expressly approved by Audi and genuine
Audi spare parts
• These parts and accessories have been specially designed to be
used on your vehicle .
• Never install accessories such as telephone cradles or beverage
holder s on airbag covers or within the airbag deployment zones .
Doing so will increase the r isk of injury if airbags are triggered in
an accident!
• Before you check anything in the engine compartment , always
read and heed all WARNINGS~
page 267. _..