2011 Alfa Romeo MiTo warning light

82GETTING TO KNOW YOUR CAR
INCREASING THE MEMORISED SPEED
Press the accelerator and store the new speed or move the lever
upwards (+). Each movement of the lever will correspond to a
slight reduction in speed (about 1 km/h), while keeping the lever
held downwards will reduce the speed continuously.
REDUCING THE MEMORISED SPEED
Deactivate the device and store the new speed or move the lever
downwards (–) until the new speed is reached. It will then auto-
matically be memorised. Each movement of the lever will corre-
spond to a slight reduction in speed (about 1 km/h), while keep-
ing the lever held downwards will correspond to a continuous speed
reduction.
DISENGAGING THE DEVICE
To disengage the device:
❍turn selector wheel A-fig. 36 to OFF;
❍switch off the engine;
❍press the brake pedal, the clutch or the accelerator; in this
last case the system is not effectively disengaged but the sys-
tem gives priority to the acceleration request. The device still
remains active, without the need to press the RES button to re-
turn to the previous condition once acceleration is concluded. When travelling downhill with the device engaged, the car may
slightly exceed the preset speed. When the device is activated
the
Üwarning light comes on, together with the relevant mes-
sage on the instrument panel (for versions/markets, where pro-
vided).
MEMORISING VEHICLE SPEED
Proceed as follows:
❍turn selector wheel A-fig. 36 to ON and press the accelerator
until the vehicle reaches the desired speed;
❍push the lever up (+) for at least one second and release it:
the car speed will be stored. The accelerator pedal may be re-
leased.
If needed (e.g. for overtaking), press the accelerator pedal to ac-
celerate: the car will return to the previously set speed when the
pedal is released.
RESTORING STORED SPEED
If the device has been disengaged - for example by pressing the
brake or clutch pedal - the memorised speed can be reset as fol-
lows:
❍accelerate gradually until reaching a speed approaching the one
memorised;
❍engage the gear selected at the time of speed memorising;
❍press button B-fig. 36 (RES).

86GETTING TO KNOW YOUR CAR
CONTROLS
HAZARD WARNING LIGHTS fig. 42
Press switch A to switch on/off the lights. Warning lights Ÿ
andΔare lit up on the instrument panel when these lights are
activated.
GLOVE COMPARTMENT LIGHT fig. 41
This light comes on automatically when the glove compartment is
opened and switches off when it is closed.
fig. 41A0J0177mfig. 42A0J0028m
The use of hazard lights is governed by the High-
way Code of the country you are in. Keep to the
rules.

GETTING TO KNOW YOUR CAR87
1
REAR FOG LIGHTS fig. 43
Press button 4to switch on/off the lights. The rear fog lights
are only enabled with the dipped beam headlights on. With lights
on, the
4warning light comes on in the instrument panel.
DOOR LOCK fig. 44
Press button A to centrally lock the doors. Locking takes place re-
gardless of the position of the ignition key.
Emergency braking
In the event of emergency braking the hazard warning lights are
lit up automatically as well as the
ŸandΔwarning lights in the
instrument panel.
The lights are switched off automatically when the nature of brak-
ing changes.
FRONT FOG LIGHTS fig. 43
(for versions/markets, where provided)
Press button
5to switch on/off the lights. The front fog lights are
only enabled with the dipped beam headlights on. With lights on,
the
5warning light comes on in the instrument panel.
fig. 43A0J0025mfig. 44A0J0030m

108GETTING TO KNOW YOUR CAR
VDC SYSTEM
(Vehicle Dynamics Control)
This is an electronic system that controls car stability in the event
of tyre grip loss.
The VDC system also includes the following systems:
❍Hill Holder
❍ASR
❍Brake Assist
❍MSR
❍CBC
❍“ELECTRONIC Q2” (“E-Q2”)
❍DST
SYSTEM INTERVENTION
This is indicated by the áwarning light flashing in the instru-
ment panel: this indicates that the vehicle is in critical stability
and tyre grip conditions.
SYSTEM ACTIVATION
The VDC system switches on automatically each time the engine
is started and cannot be switched off.
HILL HOLDER SYSTEM
This system is an integral part of the VDC system and it is provided
to facilitate starting on slopes.
It is activated automatically in the following instances:
❍uphill: car at a standstill on a road with a gradient higher than
5%, engine running, clutch and brake pedal pressed, gearbox
to neutral or engaged gear other than reverse;
❍downhill: car at a standstill on a road with a gradient higher
than 5%, engine running, clutch and brake pedal pressed and
reverse gear engaged.
At take-off the VDC system control unit will keep brake force on
the wheels until reaching the torque suitable for starting, or in
any case for 1 second in order to move easily from the brake ped-
al to the accelerator pedal.
If the vehicle has not departed after this time, the system will de-
activate automatically by gradually releasing the brake force. A
sound may be heard during this stage: this indicates that the ve-
hicle is about to move off.
IMPORTANT the Hill Holder system should not be used as a hand-
brake. Do not leave the vehicle without having engaged the hand-
brake, switched off the engine and engaged a gear.

GETTING TO KNOW YOUR CAR109
1
ASR SYSTEM (AntiSlip Regulation)
This is an integral part of the VDC system. It automatically cuts in
in the event of one or both drive wheels slipping, loss of grip on
wet roads (aquaplaning) and acceleration on slippery, snowy or icy
roads etc.
According to slipping conditions, two different control systems are
activated:
❍if slipping involves both drive wheels, the ASR function inter-
venes by reducing the power transmitted by the engine;
❍if the slipping involves only one drive wheel, the ASR system
intervenes by automatically braking the wheel that is slipping.
If the spare wheel is in use the ASR system does
not work. in this case the
áwarning light will come
on in the instrument panel.
In order for the ESP and ASR systems to operate
correctly, it is essential that the tyres are of the
same brand and type on all wheels, in perfect con-
dition and, above all, of the specified type, brand and size.
If the spare wheel is used, the VDC system keeps
operating. Be aware however that the spare wheel,
being smaller than the original wheel, provides less
grip.
The performance of the VDC and ASR systems
should not encourage the driver to take unneces-
sary risks. Your driving style should always take
road conditions, visibility and traffic into account. The dri-
ver is ultimately responsible for road safety.

GETTING TO KNOW YOUR CAR113
1
ENGAGEMENT/DISENGAGEMENT
OF “All Weather” MODE
Engagement
Move lever A-fig. 70 downwards (to the letter “a”) and hold in
this position for 0.5 seconds until the corresponding LED lights up
or the word “All Weather” appears on the display (see diagrams).
A0J0187mA0J1180g
Disengagement
To disengage “All Weather” mode and return to “Normal”, carry
out the same procedure described for“Dynamic” mode, moving
lever A-fig. 70 to “a”.
IMPORTANT NOTES
❍It is not possible to go from“Dynamic” mode straight to “All
Weather” mode and vice versa. You must always first go back
to “Normal” mode and then select the other mode.
❍If “Dynamic” mode was engaged when the engine was
switched off, the next time it is started “Normal” mode is au-
tomatically selected. If, however, “All Weather” or “Normal”,
was engaged when the engine was switched off, the selected
mode is maintained the next time it is started.
❍“Dynamic” mode cannot be engaged at speeds of above
110 km/h.
❍In the event of system failure or a fault with lever A-fig. 70,
no driving modes can be selected. The display will show a
warning message.
VDCandASR: Calibration to ensure maximum safety
Steering wheel tuning: Standard comfort
DST: More control of the brakes coordinated with VDC
Standard control of side acceleration
Steering wheel compensation: a slight pulse on the steer-
ing wheel tells on the driver to make a better manoeuvre
Engine: Standard response

114GETTING TO KNOW YOUR CAR
NoteThe engine automatic stop is allowed only after having run
at about 10 km/h, to prevent repeated engine stops when driving
at a very slow speed. The engine stopping is signalled by display-
ing the
Usymbol in fig. 71.
Engine re-starting mode
To restart the engine, press the clutch pedal.
SYSTEM MANUAL ACTIVATION/DEACTIVATION
To activate/deactivate the system, press the button fig. 72 on
the trim next to the steering wheel. When the system is deacti-
vated, the
Uwarning light in the instrument panel switches on.
For versions/markets, where fitted, a message plus a symbol on
the display may appear in the event of activation/deactivation of
the system.
START&STOP SYSTEM
(for versions/markets, where provided)
The Start&Stop system stops the engine automatically when the
vehicle stops and starts it again when the driver wants to resume
driving. In this way, the vehicle efficiency is increased, by reduc-
ing consumption, dangerous gas emissions and sound pollution.
The system is active every time the engine is started.
OPERATING MODE
Engine stopping mode
With stopped vehicle, the engine stops with gearbox in neutral and
released clutch pedal.
fig. 71A0J0279mfig. 72A0J0247m

116GETTING TO KNOW YOUR CAR
SAFETY CONDITIONS
When the engine is stopped by the Start&Stop system, if the dri-
ver releases his/her seat belt and opens the driver's or passenger's
door, the engine can be restarted only by the ignition key.
This condition is signalled by a buzzer and by a displayed message
and - for versions/markets where it has been fitted - by the flash-
ing of the
Usymbol on the display.
"ENERGY SAVING" FUNCTION
(for versions/markets, where provided)
If, as a result of the engine automatic restarting, the driver does not
make any action on the vehicle for over 3 minutes, the Start&Stop
system stops the engine once and for all, to prevent fuel consump-
tion. In these cases, the engine can be restarted only by the igni-
tion key.
Note In any case, the engine can be still kept running by deactivat-
ing the Start&Stop system.
OPERATING IRREGULARITIES
In case of malfunctioning conditions, the Start&Stop system is
deactivated. The driver is informed about the failure through the
switching-on of the warning light
èon the instrument panel and
- for versions/markets where it has been fitted - through the dis-
playing of a message + symbol. In this case, contact Alfa Romeo
Authorised Service.