2011 Acura TSX valve

227
Maintenance
Continued
Maintenance Minder™
Maintenance Service ItemsCODE Maintenance Main Items
A Replace engine oilt
*1
B Replace engine oilt
*1 and oil filter
Inspect front and rear brakes t
Check parking brake adjustment t
Inspect tie rod ends, steering gear box, and boots t
Inspect suspension components t
Inspect driveshaft boots t
Inspect brake hoses and lines (Including ABS) t
*OTQFDU
BMM
nVJE
MFWFMT
BOE
DPOEJUJPO
PG
nVJET t
Inspect exhaust system t
#
Inspect fuel lines and connections t
#
CODE Maintenance Sub Items
1 Rotate tirest
2 Replace air cleaner elementt
*2
Replace dust and pollen filter t
*3
Inspect drive belt t
33FQMBDF
USBOTNJTTJPO
nVJE t
*4
4 Replace spark plugst
Replace timing belt and inspect water pump t
*5
Inspect valve clearance t
5 Replace engine coolantt
*4: If you drive regularly in mountainous areas or tow a trailer, replace the transmission fluid at 60,000
miles (100,000 km), then every 30,000 miles (48,000 km). (automatic transmission models only)
*5: If you drive regularly in very high temperatures (over 110 °F, 43 °C ), in very low temperatures (under
-20 °F, -29 °C), or tow a trailer, replace every 60,000 miles/100,000 km. (6-cylinder models only)
#: See information on maintenance and emissions warranty. *1: Change the engine oil according to the Maintenance Minder, or annually, whichever comes first.
*2: If you drive primarily in dusty conditions, replace the air cleaner element every 15,000 miles (24,000
km).
*3: If you drive primarily in urban areas that have high concentrations of soot in the air from industry and
from diesel-powered vehicles, replace the dust and pollen filter every 15,000 miles (24,000 km).
Maintenance Service Items
Independent of the Maintenance Minder tinformation, replace the brake fluid every 3 years.
Inspect idle speed every 160,000 miles (256,000 tkm).
Adjust the valves during services A, B, 1, 2, or 3 tonly if they are noisy. Maintenance Minder
Message System Message
Indicator
Main Items
Sub Items

259
Checking and Maintaining Tires
Maintenance
Checking TiresTo safely operate your vehicle, your tires must be of the proper type and size, in
good condition with adequate tread, and properly inflated.
Inflation guidelines
Properly inflated tires provide the best combination of handling, tread life, and
comfort. Refer to the driver’s doorjamb label or specification’s page for the
specified pressure.
Underinflated tires wear unevenly, adversely affect handling and fuel economy,
and are more likely to fail from overheating.
Overinflated tires make your vehicle ride harshly, are more prone to road hazard,
and wear unevenly.
Every day before you drive, look at each of the tires. If one looks lower than the
others, check the pressure with a tire gauge.
At least once a month or before long trips, use a gauge to measure the pressure in
all tires, including the spare. Even tires in good condition can lose 1 to 2 psi (10 to
20 kPa, 0.1 to 0.2 kgf/cm
2) per month.
Inspection guidelines
Every time you check inflation, also examine the tires and valve stems.
Look for:
Bumps or bulges on the side or in the tread. Replace the tire if you find any t
cuts, splits, or cracks in the side of the tire. Replace it if you see fabric or cord.
Remove any foreign objects and inspect for air leaks. t
Uneven tread wear. Have your dealer check the wheel alignment. t
Excessive tread wear. t
Wear Indicators

P. 2 6 4
Cracks or other damage around valve stem. t
WARNING
Using tires that are excessively worn or
improperly inflated can cause a crash
in which you can be seriously hurt or
killed.
Follow all instructions in this owner’s
manual regarding tire inflation and
maintenance. Checking Tires
Measure the air pressure when tires are cold. This
means the vehicle has been parked for at least
three hours, or driven less than 1 mile (1.6 km).
If necessary, add or release air until the specified
pressure is reached.
If checked when hot, tire pressure can be as mush
as 4 – 6 psi (30 – 40 kPa, 0.3– 0.4 kgf/cm
2) higher
than if checked when cold.
Have a dealer check the tires if you feel a consistent
vibration while driving. New tires and any that have
been removed and reinstalled should be properly
balanced.

If a Tire Goes Flat
Changing a Flat Tire
282Handling the Unexpected
WARNING
Loose items can fly around the interior
in a crash and can seriously injure the
occupants.
Store the wheel, jack, and tools securely
before driving.
Storing the Flat Tire
1. Remove the center cap and place the flat
tire face down in the spare tire well.
2. Remove the spacer cone from the wing
bolt, flip it over, and insert it back on the
bolt. Secure the flat tire with the wing
bolt.
3. Securely put the jack and wheel nut
wrench back in the tool case. Store the
case in the trunk.
Storing the Flat Tire
TPMS and the Spare Tire
If you replace a flat tire with the spare tire, the low tire pressure/ TPMS indicator
comes on while you are driving. After driving for a few miles (kilometers), the
indicator will start blinking for a short time and then stay on. "CHECK TPMS
SYSTEM" appears on the multi-information display, but this is normal.
If you replace the tire with a specified regular tire, the warning message on the
multi-information display and the TPMS indicator will go off after a few miles
(kilometers).
TPMS and the Spare Tire
The system cannot monitor the pressure of the
spare tire. Manually check the spare tire pressure to
be sure that it is correct.
Use TPMS specific wheels. Each is equipped with a
tire pressure sensor mounted inside the tire behind
the valve stem.
Wing
Bolt
For
normal
tire For
compact
spare tire Spacer
Cone