249Practical information
Changing a wheel
Procedure for changing a faulty wheel for the spare wheel using the tools provided with the vehicle.
The tools are installed in the boot under the floor.
To gain access to them: )open the boot, )raise the floor, )secure it by hooking its cord on the hook
on the rear shelf suppor t,
)with a standard size spare wheel, unclip and remove the box in the middle of the
wheel containing the tools,
or )with a "space-saver" spare wheel; lift the
wheel at the rear towards you for access
to the storage box containing the tools.
Access to the tools
List of tools
All of these tools are specific to your vehicle. Do not use them for other purposes.
Wheel with trim
When removing the wheel, detach thetrim first using the wheelbrace 1pulling at the valve passage hole.When refitting the wheel
, refit the trim starting by placing its notch facing the valve and press around its edge withthe palm of your hand.
3."Bolt cover" tool.
For removing the bolt protectors (covers)on alloy wheels.4.Socket for the security bolts (located in theglove box).
For adapting the wheelbrace to the special"security" bolts. 1
.Wheelbrace.
For removing the wheel trim and the wheel
fixing bolts.
2. Jack with integral handle.For raising the vehicle.
Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not block traffic: the ground must be level, stable and non-slippery ground. Apply the parking brake unless it hasbeen programmed to automatic mode, switch off the ignition and engage first gear * to lock the wheels.Check that the braking warning lamps in the instrument panel are on(not flashing). The occupants must get out of thevehicle and wait where they are safe.If necessary, place a chock under the wheel diagonally opposite the wheel tobe changed. Never go underneath a vehicle raisedusing a jack; use an axle stand.
List of operations
)
Remove the chromed bolt cover from each
of the bolts using the tool 3 (according toequipment). )
Fit the security socket 4
on thewheelbrace 1to slacken the security bolt. )
Slacken the other bolts using the
wheelbrace 1only.
*
position
Rfor the electronic gearbox system;
P
for an automatic gearbox.
253Practical information
)Place the jack 2 in contact with one of thetwo front Aor rear B
locations provided on
the underbody, whichever is closest to the
wheel to be changed.
)Extend the jack 2until its base plate is in contact with the ground. Ensure that thecentreline of the jack base plate is directly below the location A
or Bused. )Raise the vehicle until there is sufficientspace between the wheel and the ground
to admit the spare (not punctured) wheel easily.
) Remove the bolts and store them in a clean
place. ) Remove the wheel.
Fitting a steel or "space-saver" spare wheel
If your vehicle is fitted with alloy wheels, when tightening the bolts onfitting it is normal to notice that thewashers do not come into contact with the steel or "space-saver" spare wheel.The wheel is secured by the conical contact of each bolt.
List of operations
)Put the wheel in place on the hub. )Screw in the bolts by hand to the stop.
)Pre-tighten the security bolt using the
wheelbrace 1fitted with the security socket 4. )Pre-tighten the other bolts using the
wheelbrace 1only.
After changing a wheel
To store the punctured wheel in the boot correctly, first remove the centralcover. When using the "space-saver" typespare wheel, do not exceed 50 mph(80 km/h). Have the tightening of the bolts and thepressure of the spare wheel checked by a CITROËN dealer or a qualified workshop without delay. Have the punctured wheel repaired andreplace it on the vehicle as soon aspossible.
255
Practical information
)Lower the vehicle fully. )Fold the jack 2 and detach it. )
Tighten the security bolt using the
wheelbrace 1 fitted with the securitysocket 4. )
Tighten the other bolts using the
wheelbrace 1 only. )
Refit the chromed bolt covers on each of
the bolts (according to equipment). ) Store the tools in the box.
279Practical information
Accessories A wide range of accessories and genuine par ts is available from the CITROËN dealer network.
These accessories and par ts have been tested and approved for reliability and safety.
They are all adapted to your vehicle and benefit from CITROËN's recommendation and warranty.
"Comfort":
door deflectors, side window blinds, rear screen blind, isotherm module, coat hanger fixed to head restraint, mobile reading lamp, mirror for caravan, parking sensors...
"Transport systems":
child seats and booster cushions, boot carpet,
boot liner, boot net, boot spacers, transverse
roof bars, bic
ycle carrier, ski carrier, roof boxes,
towbars, wiring harnesses...
"Styling":
gear lever knobs, aluminium foot rest, alloy wheels, chrome mirror shells, chrome door aperture finishers...
"Security and safety":
anti-intrusion alarm, anti-tilt unit, stolen
vehicle tracking system, child seats and
booster cushions, breathalyser, first aid kit, fire
extinguisher, warning triangle, high visibility
vest, wheel security bolts, snow chains,non-slip covers...
If a towbar and wiring harness are fittedoutside the CITROËN dealer network, the installation must be done followingthe manufacturer's recommendations.
* To avoid an
y risk of jamming the pedals:
- ensure that mats are correctl
y positionedand secured,
- never fit one mat on top of another.
"Protection":
mats *
, seat covers compatible with lateral
airbags, mud flaps, door protective mouldings,
bumper protection strips, vehicle cover...
