2011.5 Citroen DS4 RHD gearbox

Driving

Manual operation
)
Select position Mfor sequential
changing
of the six gears. ) Push the lever towards the +sign to change up a gear.
)
Pull the lever towards the -
sign to change
down a gear.
It is onl
y possible to change from one gear to
another if the vehicle speed and engine speed
permit; otherwise, the gearbox will operate
temporarily in automatic mode.
Ddisappears and the gearsengaged appear in succession in the
instrument panel.
I
f the engine speed is too low or too high, the
gear selected flashes for a few seconds, then
the actual gear engaged is displayed.
It is possible to chan
ge from position D(automatic) to position M
(manual) at any time.
When the vehicle is stationary or moving
very slowly, the gearbox selects gear M1automatically.
The spor t and snow programmes do not operate in manual mode.

Sport and snow programmes


Sport programme "S"
)Press button "S"
, after star ting the engine.
The gearbox automatically favours a dynamicstyle of driving.
S
appears in the instrument panel.


Snow programme "7
"
)Press button "7", after star ting the engine.
The gearbox adapts to driving on slipperyroads.
This programme improves star ting and drive
when traction is poor.
7appears in the instrument panel.

Return to automatic
operation
)
At any time, press the button selected
again to quit the programme engaged andreturn to auto-adaptive mode.
These two special pro
grammes supplement the
automatic operation in very specific conditions of use.

Invalid value during manualoperation
This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).

Stopping the vehicle
Before switching off the engine, you canengage position Por N
to place the gearbox in neutral.
In both cases, apply the parking brake toimmobilise the vehicle, unless it is programmedto automatic mode.

If the lever is not in position P, when thePdriver's door is opened or approximately45 seconds after the ignition is switched off, there is an audible signal and amessage appears.)Return the lever to position P
; the audible signal stops and themessage disappears.


Operating fault

When the ignition is on, the lighting of this
warning lamp, accompanied by an audible
signal and a message in the multifunction
screen, indicates a gearbox malfunction.
In this case, the gearbox switches to back-up
mode and is locked in 3rd
gear. You may feel
a substantial knock when changing from Pto R
and from N
to R
. This will not cause any
damage to the gearbox.
Do not exceed 60 mph (10 0 km/h), local speed restrictions permitting.
Have it checked by a CITROËN dealer or aqualified workshop.
This warning lamp may also come on if a door
is opened.
You risk damaging the gearbox:


- if you press the accelerator and brake pedals at the same time,

- if you force the lever from position Pto another position when the batteryis flat.

To reduce fuel consumption when stationary for long periods with the engine running (traffic jam...), positionthe gear lever at Nand apply theparking brake, unless it is programmed in automatic mode.

211Driving
System which keeps your vehicle immobilised
temporaril
y (approximately 2 seconds) whenstarting on a gradient, the time it takes to move your foot from the brake pedal to the
accelerator pedal.
This function is onl
y active when:


- t
he vehicle is completely stationary, with your foot on the brake pedal,

- when cer tain conditions of gradient are met,

- with the driver’s door closed.
The hill start assist function cannot bedeactivated.






Hill start assist
On an ascending slope, with the vehicle
stationary, the vehicle is held for a brief moment when you release the brake pedal:- if you are in first gear or neutral with a
manual gearbox,
- if you are in position A
or Mwith the electronic gearbox system,
- if you are in position D
or Mwith an
automatic gearbox.
Operation

Operatin
g fault

If a fault occurs with the system, these warninglamps come on. Contact a CITROËN dealer or a qualified workshop to have the system
checked.


Do not leave the vehicle while it is being held in the hill star t assist phase.
If you need to leave the vehicle whilethe engine is running, apply the parking brake manually then ensure that theparking brake warning lamp is on (notflashing) in the instrument panel.On a descending slope, with the vehicle
stationar
y and reverse gear engaged, thevehicle is held for a brief moment when you
release the brake pedal.

Stop & Start The Stop & Start system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...).
The engine restar ts automatically - START mode - as soon as you want to move off. The restar t takes place instantly, quickly and silently.
Per
fect for urban use, the Stop & Star t system reduces fuel consumption and exhaust emissions as well as the noise level when stationary.
Operation
Going into engine STOP mode
With the electronic gearbox system, for your comfor t during parking maoeuvres, STOP mode is not available for a few seconds after coming out of reverse gear.STOP mode does not affect the functionality of the vehicle, such asbraking, power steering, for example.
Never refuel with the engine in STOPmode; you must switch off the ignition with the key. Th
e "ECO"warning lamp comes on
in the instrument panel and the engine goes into standby automatically:
-with a manual gearbox , at speeds below
12 mph (20 km/h), when you put the gear lever into neutral and release the clutchpedal,
- with the 6-speed electronic gearbox
system, at a speed below 5 mph (8 km/h),
when you press the brake pedal or put thegear lever into position N.
If your vehicle is fitted with the system, a time counter calculates
the sum o
f the periods in STOP
mode during a journey. It resets
itself to zero every time the ignition
is switched on with the key.
STOP mode is not invoked when:


- the driver’s door is open,

- the driver’s seat belt is not fastened,

- the vehicle has not exceeded 6 mph
(10 km/h) since the last engine start usingthe key,

- the electric parking brake is applied or
being applied,

-the engine is needed to maintain a comfortable
temperature in the passenger compartment,
- demisting is active,

- some special conditions (battery charge, engine temperature, braking assistance,ambient temperature...) where the engine isneeded to assure control of a system.


Special cases: STOP modeunavailable

In this case, the "ECO"
warning lamp
flashes for a few seconds, then goes off.
This operation is per fectly normal.

213Driving

Going into engine START mode
The "ECO"warning lamp goes off and the engine star ts automatically:
-with a manual gearbox
, when you fullydepress the clutch pedal,-with the 6-speed electronic gearbox
system:●
gear lever in position Aor M
, when yourelease the brake pedal,
●
or gear lever in position Nand the brake pedal released, when you move the gear lever to position A
or M,●
or when you engage reverse gear.


Special cases: START invoked automatically

If the system has been deactivatedin STOP mode, the engine restar ts immediately.

With a manual gearbox in STOP mode,if a gear is engaged without fullydepressing the clutch pedal,a warning lamp comes on or an aler t message is displayed asking you to depress the clutch pedal to restar t
the engine.
At any time, press the "ECO OFF"
switch todeactivate the system.
This is confirmed by the switch warning lamp coming on accompanied by the display of amessage.


Deactivation
In this case the "ECO"warning lamp flashes for few seconds, then goesof f.
This operation is per fectly normal.
For safety reasons or to ensure smooth
operation, START mode is invoked
automatically when:
- you open the driver’s door,
- you unfasten the driver’s seat belt,
- the speed of the vehicle exceeds 15 mph (25 km/h) with a manual gearbox or 7 mph (11 k m/h) with the 6 -speed electronic
gearbox system,
- the electric parkin
g brake is being applied,
- some special conditions (battery charge,engine temperature, braking assistance,
ambient temperature...
) where the engine is
needed to assure control of a system.

221Driving





Cruise control
System which automatically maintains thespeed of the vehicle at the value programmed
by the driver, without any action on the
accelerator pedal.
The
functions of this system are grouped
together on the steering mounted controls.
1
.Cruise control mode selection dial.
2. Speed programming/value decreasebutton.3.
Speed programming/value increase button.4.
Cruise control off/resume button.
5. Memorised speeds display button.(see "Memorising speeds")
Steering mounted controls
The cruise control system cannot, in any
circumstances, replace the need to respect speed limits, nor can it replace the need for vigilance and responsibility on the par t of the driver.
You are advised to keep your feet near the pedals at all times.

The programmed information is grouped
together in the instrument panel screen.
6
. Cruise control off/resume indication.
7.Cruise control mode selection indication. 8. Programmed speed value.9.Selecting a stored speed.
(see "Storing speeds")

Displays in the instrument panel


Operation

The cruise control is switched on
manually: it
requires a minimum vehicle speed of 25 mph
(40 km/h) and engagement of:


- fourth gear on the manual gearbox,

- second gear on the electronic gearbox system or automatic gearbox, in sequentialdriving mode,

- position A
on the electronic gearboxsystem or Don an automatic gearbox.
The cruise control is switched off
manually for by pressing the brake or clutch pedal or
on triggering of the ESP system for safety reasons.
It is possible to exceed the programmed speed
temporarily by pressing the accelerator pedal.
To return to the programmed speed, simply
release the accelerator
pedal.
Switching off the ignition cancels any programmed speed value.

239Checks
Par ticle emission filter (Diesel)
On a new vehicle, the first operations of regeneration of the par ticle emissions filter may be accompanied by the smell of "burning", w hic h is per fec t ly normal.Following prolonged operation of the vehicle at very low speed or at idle,you may, in exceptional circumstances,notice the emission of water vapour at the exhaust on acceleration. This doesnot affect the behaviour of the vehicleor the environment.
Manual gearbox

The gearbox does not require anymaintenance (no oil change).
Refer to the ser vicing booklet for the
details of the level checking interval for this component.
According to your version of instrument panel, the start of
saturation of the par ticle emissions filter is indicated by:
6-speed electronic gearbox
s
ystem
The gearbox does not require anymaintenance (no oil change).
Refer to the ser vicing booklet for
details of the checking inter val for
this component.
-
temporary illumination of theservice warning lamp, accompanied
b
y an audible signal and a message
that there is a risk of blockage of thepar ticle emissions filter.
-fixed illumination of the particle
emissions filter warning lamp,accompanied by an audible signaland a message that there is a risk of blockage of the particle emissions filter,
or

As soon as the traffic conditions permit,
regenerate the filter by driving at a speed of at
least 40 mph (60 km/h) until the warning lamp goes off.
If the warning lamp stays on, refer to the
"Additive level" section.
Automatic gearbox
The gearbox does not require anymaintenance (no oil change).
Refer to the ser vicing booklet for
details of the level checking intervalfor this component.

Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not block traffic: the ground must be level, stable and non-slippery ground. Apply the parking brake unless it hasbeen programmed to automatic mode, switch off the ignition and engage first gear * to lock the wheels.Check that the braking warning lamps in the instrument panel are on(not flashing). The occupants must get out of thevehicle and wait where they are safe.If necessary, place a chock under the wheel diagonally opposite the wheel tobe changed. Never go underneath a vehicle raisedusing a jack; use an axle stand.


List of operations
)
Remove the chromed bolt cover from each
of the bolts using the tool 3 (according toequipment).)
Fit the security socket 4
on thewheelbrace 1to slacken the security bolt. )
Slacken the other bolts using the
wheelbrace 1only.

*
position
Rfor the electronic gearbox system;
P
for an automatic gearbox.