2010 YAMAHA XT660Z turn signal

PERIODIC MAINTENANCE AND ADJUSTMENT
7-32
1
2
3
4
5
6
7
8
9
10
ECA10640
NOTICE
Do not use a fuse of a higher am-
perage rating than recommended
to avoid causing extensive damage
to the electrical system and possi-
bly a fire.
3. Turn the key to “ON” and turn on
the electrical circuit in question to
check if the device operates.
4. If the fuse immediately blows
again, have a Yamaha dealer
check the electrical system.
1. Parking lighting fuse
2. Signaling system fuse
3. Headlight fuse
4. Ignition fuse
5. Electronic fuel injection fuse
6. Radiator fan fuse
7. Backup fuse
8. Reserve fuses
The main fuse and fuse box are locat-
ed under the seat. (See page 7-31.)
If a fuse is blown, replace it as follows.
1. Turn the key to “OFF” and turn off
the electrical circuit in question.
2. Remove the blown fuse, and then
install a new fuse of the specified
amperage.
7
8
654321Specified fuses:
Main fuse:
30 A
Parking lighting fuse:
10 A
Signalling system fuse:
10 A
Headlight fuse:
20 A
Ignition fuse:
10 A
Fuel injection system fuse:
10 A
Radiator fan fuse:
7.5 A
Backup fuse (for odometer,
clock and immobilizer):
10 A
XT660Z 05-07 ING-AUS:MY03 04-06 ING 11-05-2009 10:10 Pagina 7-32

PERIODIC MAINTENANCE AND ADJUSTMENT
7-34
1
2
3
4
5
6
7
8
9
10
ECA10650
NOTICE
Take care not to damage the fol-
lowing parts:
●Headlight bulb
Do not touch the glass part
of the headlight bulb to keep
it free from oil, otherwise the
transparency of the glass,
the luminosity of the bulb,
and the bulb life will be ad-
versely affected. Thoroughly
clean off any dirt and finger-
prints on the headlight bulb
using a cloth moistened with
alcohol or thinner.
●Headlight lens
Do not affix any type of tinted
film or stickers to the head-
light lens.
Do not use a headlight bulb
of a wattage higher than
specified.4. Connect the coupler, and then in-
stall the headlight bulb cover.
5. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAU24204
Replacing a turn signal
light bulb
1. Screw
2. Turn signal light lens
3. Turn signal light bulb
1. Remove the turn signal light lens
by removing the screw.
2. Remove the burnt-out bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
XT660Z 05-07 ING-AUS:MY03 04-06 ING 11-05-2009 10:10 Pagina 7-34

SPECIFICATIONS
9-3
1
2
3
4
5
6
7
8
9
10
Rear suspension:
Type:
Swingarm (link suspension)
Spring/damper type:
Coil spring/gas-oil damper, spring
preload adjustable
Wheel travel:
200 mm (7.87 in)
Electrical system:
Ignition system:
Transistorized coil ignition (digital)
Charging system:
A.C. magneto
Battery:
Model:
GT9B-4
Voltage, capacity:
12 V, 8 Ah
Headlight:
Bulb type:
Halogen bulb
Bulb voltage, wattage x quantity:Headlight:
12 V, 55 W x 2
Auxiliary light:
12 V, 5 W x 2
Tail/brake light:
LED
Front turn signal light:
12 V, 10 W x 2
Rear turn signal light:
12 V, 10 W x 2
Meter lighting:
LED (backlight)Neutral indicator light:
LED
Turn signal indicator light:
LED
High beam indicator light:
LED
Coolant temperature warning light:
LED
Engine trouble warning light:
LED
Immobilizer system indicator light:
LED
Fuses:Main fuse:
30 A
Headlight fuse:
20 A
Signaling system fuse:
10 A
Ignition fuse:
10 A
Parking lighting fuse:
10 A
Radiator fan fuse:
7.5 A
Fuel injection system fuse:
10 A
Backup fuse (for odometer, clock and
immobilizer):
10 A
XT660Z 08-10 ING-AUS:MY03 07-10 ING 11-05-2009 10:10 Pagina 8

INDEX
1
2
3
4
5
6
7
8
9
10
Dimmer switch ................................4-9
Engine stop switch .........................4-9
Hazard switch ...............................4-10
Horn switch .....................................4-9
Pass switch .....................................4-9
Start switch .....................................4-9
Turn signal switch ...........................4-9
Headlight bulb, replacing..................7-33
High beam indicator light ...................4-4
Horn switch ........................................4-9
I
Identification numbers ......................10-1
Idling speed, checking .....................7-15
Ignition circuit cut-off system............4-17
Checking operation procedure......4-18
Immobilizer system ............................4-1
Immobilizer system indicator light ......4-4
Indicator and warning lights ...............4-3
Coolant temperature warning light..4-4
Engine trouble warning light ...........4-4
High beam indicator light ................4-4
Immobilizer system indicator light...4-4
Neutral indicator light ......................4-4
Turn signal indicator light ................4-3
Instruments ........................................3-3
Instrument and control functions........4-1
K
Key identification number .................10-1
Keys ...................................................4-1L
Labels (location of important labels) ..1-1
License plate light bulb, replacing ....7-35
Location of important labels ...............1-1
Loading ..............................................2-3
Lubricating the brake and clutch
levers ............................................7-26
Lubricating the brake pedal..............7-27
Lubricating the cables ......................7-25
Lubricating the drive chain ...............7-25
Lubricating the sidestand .................7-27
Lubricating the throttle grip
and cable ......................................7-26
Lubricating the swingarm pivots.......7-28
M
Main switch/steering lock ...................4-2
Model label .......................................10-2
Motorcycle noise regulation
(for Australia) ................................10-2
Multi-function display..........................4-5
Clock mode .....................................4-7
Self-diagnosis devices ....................4-7
Tachometer .....................................4-6
Tripmeter and tachometer modes ...4-6
N
Neutral indicator light .........................4-4
O
Oil filter element ..............................7-10
Operation and important riding
points ..............................................6-1Owner’s tool kit...................................7-1
P
Panels, removing and installing .........7-6
Parking ...............................................6-4
Pass switch ........................................4-9
Periodic maintenance
and adjustment ...............................7-1
Periodic maintenance chart for
the emission control system ...........7-2
Pre-operation check list......................5-2
Pre-operation checks .........................5-1
R
Rear suspension, lubricating............7-27
Rear wheel .......................................7-38
Installing........................................7-39
Removing......................................7-38
Record the identification numbers ...10-1
S
Safety information ..............................2-1
Seat ..................................................4-14
Self-diagnosis devices .......................4-7
Shift pedal ........................................4-10
Shifting ...............................................6-2
Shock absorber assembly
(adjusting) .....................................4-16
Sidestand .........................................4-17
Sidestand, checking and lubricating ..7-27
Sidestand switch, checking ..............4-18
Spark plug, checking..........................7-8
XT660Z 08-10 ING-AUS:MY03 07-10 ING 11-05-2009 10:10 Pagina 2

1
2
3
4
5
6
7
8
9
10
INDEX
Specifications .....................................9-1
Spoke wheels ...................................7-19
Start switch ........................................4-9
Starting the engine.............................6-1
Steering, checking............................7-29
Steering lock ......................................4-2
Storage...............................................8-3
Supporting the motorcycle ...............7-36
Swingarm, lubricating the pivots ......7-28
T
Tachometer ........................................4-6
Throttle cable free play, checking.....7-16
Throttle grip and cable, checking
and lubricating ..............................7-26
Tips for reducing fuel consumption ....6-3
Tires .................................................7-16
Air pressure ..................................7-16
Tire information .............................7-18
Tire inspection ..............................7-18
Tool kit ................................................7-1
Tripmeter and tachometer modes ......4-6
Troubleshooting ................................7-39
Troubleshooting charts .................7-40
Engine overheating .......................7-41
Turn signal indicator light ...................4-3
Turn signal light bulb, replacing........7-34
Turn signal switch...............................4-9V
Valve clearance ................................7-16
Vehicle identification number ...........10-1
W
Warning lights ....................................4-3
Wheel bearings, checking ................7-29
Wheels, spoke..................................7-19
XT660Z 08-10 ING-AUS:MY03 07-10 ING 11-05-2009 10:10 Pagina 3