2010 YAMAHA XMAX 250 lights

EAU16793
BrakingEWA10300
Avoid braking hard or suddenly
(especially when leaning over
to one side), otherwise the sco-
oter may skid or overturn.
Railroad crossings, streetcar
rails, iron plates on road cons-
truction sites, and manhole
covers become extremely slip-
pery when wet. Therefore, slow
down when approaching such
areas and cross them with cau-
tion.
Keep in mind that braking on a
wet road is much more difficult.
Ride slowly down a hill, as bra-
king downhill can be very diffi-
cult.
1. Close the throttle completely.
2. Apply both front and rear brakessimultaneously while gradually
increasing the pressure. Front
Rear
EAU16820
Tips for reducing fuel
consumption
Fuel consumption depends largely on
your riding style. Consider the follo-
wing tips to reduce fuel consumption:
Avoid high engine speeds during
acceleration.
Avoid high engine speeds with no
load on the engine.
Turn the engine off instead of let-
ting it idle for an extended length
of time (e.g., in traffic jams, at
traffic lights or at railroad cros-
sings).

WARNING

OPERATION AND IMPORTANT RIDING POINTS
5-3
5

37P-F8199-E0 18/9/09 14:54 Página 40

PERIODIC MAINTENANCE AND ADJUSTMENT
6-6
6
ODOMETER READING
CHECK OR ANNUAL
NO. ITEM MAINTENANCE JOB 1000 km 10000 km 20000 km 30000 km 40000 kmCHECK
(600 mi) (6000 mi) (12000 mi) (18000 mi) (24000 mi)
• Check coolant level and vehicle
19 * Cooling system for coolant leakage. √√√ √√
• Change. Every 3 years
20Final transmission
• Check vehicle for oil leakage.
√√ √oil
• Change. √√ √
21 * V-belt • Replace. When the V-belt replacement indicator flashes
[every 20000 km (12000 mi)]
22 * Front and rear brake
switches • Check operation.
√√ √ √ √ √
23 Moving parts and
cables • Lubricate.
√√√ √√
• Check operation and free play.
Throttle grip • Adjust the throttle cable free
24 * housing play if necessary. √√√ √√
and cable • Lubricate the throttle grip
housing and cable.
25 * Lights, signals and
• Check operation.
switches • Adjust headlight beam. √√ √ √
√√

37P-F8199-E0 18/9/09 14:54 Página 47

amperage. WARNING! Do not
use a fuse of a higher ampera-
ge rating than recommended
to avoid causing extensive
damage to the electrical sys-
tem and possibly a fire.
[EWA15131]
TIP
Fuse tongs and a bag containing spa-
re fuses are included in the owner’s
tool kit. Use the tongs to remove and
install a fuse.
1. Radiator fan fuse
2. ECU fuse
3. Backup fuse
4. Signaling system fuse
5. Headlight fuse
6. Ignition fuse
7. Spare fuse
8. Spare fuse
9. Spare fuse
3. Turn the key to “ON” and turn on the electrical circuit in question to
check if the device operates.
4. If the fuse immediately blows again, have a Yamaha dealer
check the electrical system.
EAU34240
Replacing a headlight bulb
This model is equipped with quartz
bulb headlights. If a headlight bulb
burns out, have a Yamaha dealer
replace it and, if necessary, adjust the
headlight beam.
Specified fuses:Main fuse:30.0 A
Headlight fuse: 15.0 A
Signaling system fuse: 10.0 A
Ignition fuse: 10.0 A
Radiator fan fuse: 7.5 A
Hazard fuse: 10.0 A
ECU fuse: 5.0 A
Backup fuse: 5.0 A

PERIODIC MAINTENANCE AND ADJUSTMENT
6-26
6

37P-F8199-E0 18/9/09 14:54 Página 67

6. Insert a new bulb into the socket,push it in, and then turn it clock-
wise until it stops.
7. Install the bulb holder together with the dust protector by pus-
hing both into the original posi-
tion.
TIP
Place the bulb holder and dust cover
correctly in its position to avoid dust
and water entering.
8. Install the screws and thetail/brake light unit.
9. Install the panel.
EAU47910
Replacing the license plate
light bulb
1. Remove the license plate light cover by removing the screw.
1. Screw
2. License plate light bulb socket
2. Remove the burnt-out bulb bypulling it out from the socket.
3. Insert a new bulb into the socket.
4. Install the license plate light cover by installing the screw.
EAU43231
Replacing an auxiliary light
bulb
This model is equipped with two auxi-
liary lights. If an auxiliary light bulb
burns out, replace it as follows.1. Remove the socket (together with the bulb) by pulling it out.
1. Auxiliary light bulb socket
2. Remove the burnt out bulb bypulling it out.
3. Insert a new bulb into the socket.
4. Install the socket (together with the bulb) by pushing it in.





PERIODIC MAINTENANCE AND ADJUSTMENT
6-28
6

37P-F819D-E0 18/9/09 20:35 Página 69

EAU25881
Troubleshooting
Although Yamaha scooters receive a
thorough inspection before shipment
from the factory, trouble may occur
during operation. Any problem in the
fuel, compression, or ignition sys-
tems, for example, can cause poor
starting and loss of power.
The following troubleshooting charts
represent quick and easy procedures
for checking these vital systems your-
self. However, should your scooter
require any repair, take it to a Yamaha
dealer, whose skilled technicians
have the necessary tools, experience,
and know-how to service the scooter
properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life and
can lead to expensive repair bills.
EWA15141
When checking the fuel system, do
not smoke, and make sure there
are no open flames or sparks in thearea, including pilot lights from
water heaters or furnaces. Gasoli-
ne or gasoline vapors can ignite or
explode, causing severe injury or
property damage.

WARNING

PERIODIC MAINTENANCE AND ADJUSTMENT
6-29
6

37P-F8199-E0 18/9/09 14:54 Página 70

with water may be used. Be
sure to rinse off any detergent
residue using plenty of water,
as it is harmful to plastic parts.
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.
Do not use high-pressure was-
hers or steam-jet cleaners sin-
ce they cause water seepage
and deterioration in the follo-
wing areas: seals (of wheel and
swingarm bearings, fork and
brakes), electric components
(couplers, connectors, instru-
ments, switches and lights),
breather hoses and vents.
For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or scrat-
ching. Some cleaning com-
pounds for plastic may leavescratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not lea-
ve any marks. If the windshield
is scratched, use a quality
plastic polishing compound
after washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottle-
brush for hard-to-reach areas. Stub-
born dirt and insects will come off
more easily if the area is covered with
a wet cloth for a few minutes before
cleaning.
After riding in the rain, near the sea or
on salt-sprayed roads
Since sea salt or salt sprayed on the
roads during winter are extremely
corrosive in combination with water,
carry out the following steps after
each ride in the rain, near the sea or
on salt-sprayed roads.
TIP
Salt sprayed on roads in the winter
may remain well into spring.
1. Clean the scooter with cold water
and a mild detergent after the
engine has cooled down. NOTI-
CE: Do not use warm water
since it increases the corrosive
action of the salt.
[ECA10791]
2. Apply a corrosion protection spray on all metal, including
chrome- and nickel-plated, surfa-
ces to prevent corrosion.
After cleaning 1. Dry the scooter with a chamois or an absorbing cloth.
2. Use a chrome polish to shine chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally indu-
ced discoloring of stainless-steel
exhaust systems can be removed
through polishing.)
SCOOTER CARE AND STORAGE
7-2
7

37P-F8199-E0 18/9/09 14:54 Página 74

AAcceleration and deceleration ...................5-2
Air filter and V-belt case air filter elements ................................................6-15
Auxiliary light bulb, replacing ...................6-28
BBattery......................................................6-24
Brake fluid level, checking .......................6-20
Brake fluid, changing ...............................6-21
Brake lever, front ......................................3-12
Brake lever, rear .......................................3-12
Brake levers, lubricating ..........................6-21
Braking .......................................................5-3
CCare............................................................7-1
Catalytic converters .................................3-14
Centerstand and sidestand, checking and lubricating .......................................6-22
Coolant.....................................................6-13
Cowling and panel, removing and installing ...................................................6-8
DDimmer switch .........................................3-11
EEngine break-in ..........................................5-4
Engine oil .................................................6-10
Engine trouble warning light ......................3-4
FFinal transmission oil ...............................6-12
Front and rear brake lever free play.........6-18
Front and rear brake pads, checking ......6-19
Front fork, checking .................................6-23
Fuel ..........................................................3-13
Fuel consumption, tips for reducing ..........5-3 Fuel tank cap ...........................................3-12
Fuses, replacing .......................................6-25
HHandlebar switches .................................3-11
Hazard switch ..........................................3-11
Headlight bulb, replacing .........................6-26
High beam indicator light...........................3-4
Horn switch ..............................................3-11
IIdentification numbers ...............................9-1
Ignition circuit cut-off system ..................3-19
Immobilizer system ....................................3-1
Immobilizer system indicator light .............3-4
Indicator and warning lights ......................3-4
KKey identification number ..........................9-1
LLicense plate light bulb, replacing ...........6-28
MMain switch/steering lock ..........................3-2
Maintenance and lubrication, periodic ......6-4
Maintenance, emission control system .....6-3
Matte color, caution ...................................7-1
Model label ................................................9-2
Multi-function display ................................3-6
PParking .......................................................5-4
Part locations .............................................1-5
Pass switch ..............................................3-11
SSafe-riding points.......................................1-5
Safety information ......................................1-1
Seat ..........................................................3-15
Securing bracket ......................................3-15Shock absorber assemblies, adjusting....3-18
Sidestand .................................................3-18
Spark plug, checking .................................6-9
Specifications.............................................7-3
Speedometer .............................................3-5
Start switch ..............................................3-11
Starting off .................................................5-2
Starting the engine.....................................5-1
Steering, checking ...................................6-23
Storage.......................................................7-3
Storage compartments ............................3-16
TTachometer ................................................3-5
Tail/brake light bulb or rear turn signal
light bulb, replacing ...............................6-27
Throttle cable free play, checking ............6-16
Throttle grip and cable, checking and lubricating ..............................................6-21
Tires .........................................................6-16
Tool kit ........................................................6-2
Troubleshooting .......................................6-29
Troubleshooting charts ............................6-30
Turn signal indicator lights .........................3-4
Turn signal light bulb (front), replacing ................................................6-27
Turn signal switch ....................................3-11
VValve clearance ........................................6-16
Vehicle identification number .....................9-1
WWheel bearings, checking........................6-24
Wheels .....................................................6-18
INDEX

37P-F8199-E0 18/9/09 14:54 Página 82