2010 TOYOTA SIENNA mirror

79
1-3. Adjustable components (s
eats, mirrors, steering wheel)
1
Before driving
NOTICE
■To prevent damage to the seat
●Avoid putting heavy loads on a folded seat that is being used as a tempo-
rary table.
● Before folding a second seat as preparation for removal or tumbling the
seat, the seat belt buckles must be stowed.
● Do not sit on or put heavy loads on a second seat that has been removed
from the vehicle. The metal tips of the seat leg may be damaged, prevent-
ing reinstallation of the seat.
● The second seats must be reinstalled in their original positions. If they are
installed in the wrong position, the seat locks or bezels will be damaged.
● When installing a second seat, make sure to align the front leg hooks with
the rearmost of the two bars in each of the front strikers in the floor. If you
align the legs with the front strikers, the bezel in the floor will be damaged.
● Do not use the seat position adjustment lever to lift or carry a seat that has
been disengaged from the floor or removed from the vehicle. Otherwise,
during reinstallation, part of the seat may slide preventing proper reinstal-
lation of the seat. If this happens, return the seat to the rearmost position
before reinstalling it.
● Make sure that the path the seat will move through is clear before stowing
or returning the third seat.

80
1-3. Adjustable components (seats, mirrors, steering wheel)
Driving position memor y (if equipped)
Your preferred driving position (the position of the driver’s seat and
outside rear view mirrors) can be memorized and recalled with the
touch of a button.
Two different driving positions can be entered into memory.
■ Entering a position to memory
Check that the shift lever is set in P.
Turn the engine switch to the “ON” position.
Adjust the driver’s seat and outside rear view mirrors to the
desired positions. While pushing the “SET” but-
ton, push button “1” or “2” until
the signal beeps.
If the selected button has
already been preset, the previ-
ously recorded position will be
overwritten.
■Recalling the memorized position
Check that the shift lever is set in P.
Turn the engine switch to the “ON” position. Push button “1” or “2” to recall
the memorized position.
STEP1
STEP2
STEP3
STEP1
STEP2

81
1-3. Adjustable components (s
eats, mirrors, steering wheel)
1
Before driving
■Operating the driving position memory after turning the engine switch
to the “LOCK” position
Memorized positions can be activated up to 30 seconds after the driver's
door is opened, even after turning the engine switch to the “LOCK” position.
■ To cancel memorized position recall
Perform any of the following operations.
●Push the “SET” button.
● Push button “1” or “2”.
● Adjust the seat using the switches (using the switches only cancels seat
position recall).
■ If the battery is disconnected
The memorized positions are erased when the battery is disconnected.
CAUTION
■Seat adjustment caution
Take care during seat adjustment that the seat does not strike the rear pas-
senger or squeeze your body against the steering wheel.

82
1-3. Adjustable components (seats, mirrors, steering wheel)
Head restraints
Head restraints are provided for all seats.
Front seatsVertical adjustmentUp
Pull the head restraints up.
Down
Push the head restraint down
while pushing the lock release
button.
Second seats
Vertical adjustmentUp
Pull the head restraints up.
Down
Push the head restraint down
while pushing the lock release
button.
Third seats
Vertical adjustmentUp
Pull the head restraints up.
Down
Push the head restraint down
while pushing the lock release
button.
Lock release button
Lock release button
Lock release button

83
1-3. Adjustable components (s
eats, mirrors, steering wheel)
1
Before driving
■Removing the head restraints
■ Installing the head restraints
■ Adjusting the height of the head restraints
Pull the head restraint up while pressing
the lock release button.
Align the head restraint with the installa-
tion holes and push it down to the lock
position.
Press and hold the lock release button
when lowering the head restraint.
Make sure that the head restraints are
adjusted so that the center of the head
restraint is closest to the top of your ears.

84 1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Head restraint precautions
Observe the following precautions regarding the head restraints. Failure to
do so may result in death or serious injury.
●Use the head restraints designed for each respective seat.
● Adjust the head restraints to the correct position at all times.
● After adjusting the head restraints, push down on them and make sure
they are locked in position.
● Do not drive with the head restraints removed.

85
1
1-3. Adjustable components (seats, mirrors, steering wheel)
Before driving
Seat belts
Make sure that all occupants are wearing their seat belts before driv-
ing the vehicle.
■Correct use of the seat belts
●Extend the shoulder belt so
that it comes fully over the
shoulder, but does not
come into contact with the
neck or slide off the shoul-
der.
● Position the lap belt as low
as possible over the hips.
● Adjust the position of the
seatback. Sit up straight
and well back in the seat.
● Do not twist the seat belt.
■ Fastening and releasing the seat belt
Fastening the belt
Push the tab into the buckle
until a clicking sound is heard.
Releasing the belt
Press the release button.
Release button

86 1-3. Adjustable components (seats, mirrors, steering wheel)
Center third seat belt
The center third seat belt is a 3-point type restraint with 2 buckles.
Both seat belt buckles must be correctly located and securely latched
for proper operation. Make sure that the buckle is
securely latched for ready use of
the center seat belt.Matches the tab with the
hooked end.
Matches the tab with the con-
cave end.
■Adjusting the height of the belt (front seats)
Down
Up
Move the height adjuster up
and down as needed until you
hear a click.