2010 SKODA OCTAVIA TOUR ECU

Seats and Storage61
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
seats and the armrest in such a way that no mutual deformation or damage can occur
to the seats.
Folding seats forwards– Before folding the rear seats forwards, yo
u must adapt the position of the front
seats in such a way that they are not damaged when the rear seats are folded
forwards.
– Pull up the seat cushion in direction of arrow and fold forwards in direction of arrow page 60, fig. 59 .
– Unlock the seat backrests by pulling the securing knob page 60, fig. 60 and fold
them forwards.
– Remove the head restraints from the seat backrests and fold the backrests
completely forwards.
– The head restraints can be inserted into the relevant holes of the folded forward
seat cushions.
If the front seats are too far back, we recomm end that you have the rear head restraints
removed before the seat backrests are folded forward. Store the removed head
restraints in such a way that they cannot be damaged or soiled. Please refer to the
guidelines page 63, “luggage compartment”.Move seats into the initial position
Move seats into the initial position– Install the head restraints in the slightly lifted seat backrest.
– Place the rear lateral seat belt fig. 61 behind the edge of the side trim panel.
– Then push the seat backrest back into th e upright position until the securing knob
clicks into place - check by pulling on the seat backrest.
– Move the seat cushion into its original position.
WARNING

The belts and the belt locks must be in their original position after folding
back the seat cushions and the seat backrests - they must be ready to use.

The seat backrests must be securely interlocked in position so that no
objects in the luggage compartment can slide into the passenger compartment
if there is sudden braking - risk of injury!

Pay attention that the seat backrests are correctly interlocked. It is only then
that the three-point seat belt for the middle seat can reliably fulfil its function.

Before folding the seat backrest back into the secure position, place the rear
lateral seat belt behind the edge of the si de trim panel. Take suitable measures
to prevent that the seat belt is jammed between the seat backrest and the side
trim panel and is thus damaged.
Removing the seat cushion
A1
A2
Fig. 61 Lock the seat backrest
AA
Fig. 62 Removing seat cushions
s2rc.book Page 61 Thursd ay, April 22, 2010 10:58 AM

Seats and Storage
62
The luggage compartment can be increased furt her in size by removing the rear seat.Removing– Fold the seat cushion forwards completely.
– Press the wire clamps in the direction of the arrow fig. 62 and remove the seat
cushion from its holder.Installing– Press the wire clamps in the direction of the arrow and place it in its holder.
– Fold the seat cushion back into its original position.Seat heating of the front seats*You can electrically heat the seat cushions and the seat backrests of the front seats
when the ignition is switched on.Front seats– He ating on the driv er's and f ront pa se nger's s eat can be swi tche d on and regula te d by turning the control dial fig. 63 .
– The system is switched off by turning th e control dial to the home position “0”.
WARNING
If, as an occupant, you have a subdued pa in and/or temperature sensitivity, e.g.
through medication, paralysis or because of chronic illness (e.g. diabetes), we
recommend not to use the seat heating. This can lead to burns on the back, the
posterior and the legs which are difficult to heal. If the seat heating is used, we
recommend to make regular breaks in your journey when driving long
distances, so that in specific cases as mentioned above the body can recuperate
from the stress of the journey. Please consult your doctor, who can evaluate
your specific condition.
Caution

You should not kneel on the seats or otherwise apply pressure at specific points in
order to avoid damaging the heating elements of the seat heaters.

Do not clean the seats moist page 142.Note

The seat heating should only be switched on when the engine is running. This has
a significant effect of savi ng on the battery capacity.

If the on-board voltage drops, the seat heating is switched off automatically, in
order to provide sufficient electrical energy for the engine control.
PedalsConcerning a secure de pressing of the pedal, you should use only footmats from the
Škoda genuine accessories.
Operation of the pedals must not be hindered!
WARNING

Greater pedal distances may be needed when there is a fault in the brake
system.

Do not place any footmats or other additional floor coverings in the area of
the pedals in order to ensure that all the pedals can be fully depressed and are
able to return unobstructed to their initial position - risk of accident!
Fig. 63 Dash panel: Control dial
for heating the front seats
s2rc.book Page 62 Thursd ay, April 22, 2010 10:58 AM

Seats and Storage63
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data

There must be no objects on the floor which could roll under the pedals. You
would then no longer be able to apply the brakes, operate the clutch or accel-
erator - risk of accident!
luggage compartmentLoading the luggage compartmentPlease observe the following in the interest of having good handling characteristics of
your vehicle:
– Distribute the items of luggage as evenly as possible.
– Place heavy objects as far forward as possible.
– Attach the items of luggage to the lashing eyes or the fixing net* page 64.
In the event of an accident, there is such a high kinetic energy which is produced by
small and light objects that th ey can cause severe injuries. The magnitude of the kinetic
energy depends on the speed at which the vehi cle is travelling and on the weight of the
object. The speed at which the vehicle is travelling is in this case the more significant
factor.
Example: In the event of a frontal collision at a speed of 50 km/h, an unsecured object
with a weight of 4.5 kg produces an ener gy, which corresponds to 20 times its own
weight. This means that it results in a weight of approx. 90 kg. You can imagine the inju-
ries that can occur, if this “bullet” is fl ying through the interior compartment and hits
an occupant.
WARNING

Stow the objects in the luggage compartm ent and attach them to the lashing
eyes.

Loose objects in the passenger compartment can be thrown forward during
a sudden manoeuvre or in case of an accident and can injure the occupants or
other oncoming traffic. This risk is still increased, if the objects which are flying around are hit by a deployed airbag. In this case, the objects which are thrown
back can injure the occupants - hazard.

Please note that the handling properties of your vehicle may be affected
when transporting heavy objects as a result of the displacement of the centre of
gravity. The speed and style of driv ing must be adjusted accordingly.

The items carried in the luggage compartment should be stowed in such a
way that no objects are able to slip fo rward if there are any sudden driving or
braking manoeuvres underta ken - risk of injury!

Never drive with the boot lid fully open ed or slightly ajar otherwise exhaust
gases may get into the interior of the vehicle - risk of poisoning!

On no account exceed the permissible axle loads and the permissible gross
weight of the vehicle - risk of accident!

Never transport occupants in the luggage compartment!Caution
Please ensure that the heating elements of the rear window heater are not damaged
as a result of objects sliding in this area.
Note
Tyre pressure must be adjusted to the load page 160, fig. 153 .
WARNING (continued)
WARNING (continued)
s2rc.book Page 63 Thursd ay, April 22, 2010 10:58 AM

Seats and Storage65
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
The fixing net and the installation instruction are located in a container under the floor
covering of the luggage compartment behind the spare wheel.
WARNING
The whole strength of the net makes it possible to load the pocket with objects
of up to 1.5 kg in weight. Heavy objects are not secured sufficiently - risk of
injury and net damage!
Caution
Do not place any objects with sharp edges in the nets - risk of net damage.Fixing nets - Net programme Combi*
Fixing examples of th
e fixing net as double vertical pocket fig. 68 and floor net
 fig. 69 .
The fixing net and the installation instructio n are located in a container under the floor
covering of the luggage compartment behind the spare wheel.
WARNING
The whole strength of the net makes it possible to load the pocket with objects
of up to 1.5 kg in weight. Heavy objects are not secured sufficiently - risk of
injury and net damage!
Caution
Do not place any objects with sharp edge s in the nets - risk of net damage.Fixing floor covering of the luggage compartmentA plastic hook is located on the handle of the luggage compartment cover. When
handling the spare wheel, you can fix the ra ised floor covering with the hook on the
frame of the luggage compartment fig. 70 .
Fig. 68 Fixing net: Double
vertical pocketFig. 69 Fixing net: Floor net
Fig. 70 Luggage compartment:
Fixing of the floor covering
(Combi)
s2rc.book Page 65 Thursd ay, April 22, 2010 10:58 AM

Seats and Storage
68
Divide the luggage compartment with variable loading floor*The luggage compartment can be divided with the variable loading floor.
– Lift up a par t of the loading floor with the handle and secure it by moving it into the
grooves fig. 75 .Net partition (Combi)*Use the net partition behind the rear seatsThe net partition can either be installed behind the rear seats or behind the front seats.
Before using the net partition, remove the foldable cover page 66.
Pulling out– Pull the net partition out of the housing at an angle of about 45° in direction of
the boot lid at the loop .
– Insert the cross rod into the mount first on the one side and push the cross rod forwards.
– In the same way, fix the cross rod to the other side of the vehicle, mount .Folding– Push the cross rod first of all on the one side and then on the other side towards the rear.
– Take the cross rod out of the mounts .
– Roll the net partition at an angle of approx. 45° towards the boot lid in the housing , so that it does not roll up automatically .
WARNING

First check for yourself that the cross road is inserted into the mounts in
the front position!
Using the net partition behind the front seats
Fig. 75 Divide the luggage
compartmentFig. 76 Pull out the net partition
AB
AA
AC
AC
AC
AB
AC
Fig. 77 Pull out the net partition
s2rc.book Page 68 Thursd ay, April 22, 2010 10:58 AM

Seats and Storage69
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Pulling out– Fold the rear seats forwards page 60
– Pull the net partiton net at the plate out of the housing page 68, fig. 77 .
– Insert the cross rod into the mount first on the one side and push the cross rod forwards.
– In the same way, fix the cross rod to the other side of the vehicle, mount .Folding– Pull the cross rod back slightly, first on the one side then on the other side and take the cross rod out of the mounts fig. 78 .
– Hold the cross rod in such a way that the luggage net partition can roll up slowly
and without damage into the housing .
– Fold the rear seats back into their original position.
WARNING

The belt locks and the belts must be in their original position after folding
back the seat cushions and the seat backrests - they must be ready to use.

The seat backrests must be securely interlocked in position so that no
objects in the luggage compartment ca n slide into the passenger compartment
if there is sudden braking - risk of injury!

First check for yourself that the cross road is inserted into the mounts in
the front position!
Removing and installing net partition housingRemoving– Fold the rear seats forwards page 60
– Open the right rear door.
– Push the net partition housing in the di rection of arrow up to the stop and
take it out of the mounts of the seat backrest in direction of arrow .Installing– Position the net partition housing into the mounts of the rear seat backrests.
– Push the luggage net partition housing in the opposite direction of arrow as far
as the stop.
– Fold the rear seats back into their original position.
Fig. 78 Roll up net partition
AA
AB
AC
AC
AC
AB
WARNING (continued)
AC
Fig. 79 Rear seats: Net partition
housing
AB
A1
A2
A1
s2rc.book Page 69 Thursd ay, April 22, 2010 10:58 AM

Seat belts
106
Taking seat belts off– Press the red button in the belt lock fig. 114 . The spring force causes the tongue
of the lock to jump out.
– Guide the belt back with your hand to en able the inertia reel to wind up the belt
webbing more easily.
A plastic knob in the belt webbing holds the be lt tongue in a position which is easy to
get hold of.Three-point seat belt with the Interlock System*A three-point safety belt with the Interlock System is used on some vehicles instead of
a pelvic belt.
If the backrest of the rear seats is not secured, the retractor blocks and the seat belt
cannot be reeled down.Rear middle three-point safety belt with safety lock for a child seat*In order to attach a child seat the rear middle three-point safety belt with the blocking,
the so-called child safety locks, can be used.
Switching child safety lock on– Attach the child safety seat with the three-point seat belt (self-retracting) as stated
in the manufacturer's instructions.
– Reel up the shoulder part of the belt comp letely. When the belt is reeled up, this
can be detected by a “clicking” noise.
– After fixing the child seat in place, let th e belt freely reel up. Now the belt can no
longer be reeled down.
– Check if the safety lock is activated by pulling on the belt.Switching child safety lock off– By pressing the button in the lock of the safety belt, the blocking is unblocked and
afterwards the safety belt starts to reel up.
– After fully reeling up the belt, you can freely reel it down again.The pelvic belt*
Fig. 114 Releasing lock tongue
from belt lock
Fig. 115 Fasten pelvic belt
s2rc.book Page 106 Thursday, April 22, 2010 10:58 AM

Transporting children safely115
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Transporting children safelyWhat you should know about transporting children!An introduction to the subject
Accident statistics have revealed that children are generally more
safely transported on the rear seat s than on the front passenger seat.Children younger than 12 years of age should normally travel on the rear seat of the
vehicle (take note of any national legal provis ions which differ from this). They should
be secured there by means of a child restraint system or by using the existing seat belts
depending on their age, body size and we ight. The child seat should be mounted
behind the front passenger seat for safety reasons.
The physical principle of an accident does, of course, also apply to children
 page 103, “The physical principle of a fronta l collision”. They differ from adults in
that their muscles and bone structure of children are not yet fully developed. Thus chil-
dren are exposed to increased risk of injury.
Children should be transporte d by using special child safety seats in order to reduce
this risk of injury.
Use only child safety seats which are officia lly approved and are suitable for children
and which comply with the ECE-R 44 standard, which classifies child safety seats into
5 groups page 118, “Classification of child seats into groups”. Child restraint
systems which have been tested for conformity to ECE-R 44 standard have a non-
detachable test seal (a large E within a circ le and below this the test number) attached
to the seat.
We recommend that you use child safety seats from the Škoda genuine accessories.
These child seats were developed and also tested for use in Škoda vehicles. They fulfil
the ECE-R 44 standard.
WARNING
Always comply with legal provisions and instructions from the relevant child
safety seat manufacturer when inst alling and using the child seat  in
“Important safety information regard ing the use of child safety seats”.
Note
Any varying national legal regulations take priority over the information provided in
these instructions for use, or stated in this chapter.Important safety information regarding the use of child safety seats
Correct use of child safety seats cons iderably reduces the risk of injury!
WARNING

All the occupants of the car - in particular children - must wear a seat belt
when the car is moving.

Children less than 1.50 m in height or younger than 12 years must not use a
normal seat belt without a child restraint system otherwise this may result in
injuries to the stomach and neck areas. Comply with the national legal require-
ments.

One should never carry children, and also not babies! - on one's lap.

You can transport a child safely in a suitable child safety seat page 118,
“Child seat”!

Only one child may be fastened with a seat belt into a child safety seat.

Never leave the child sitting unattended in the seat.

Certain outside climatic conditions can cause life-threatening tempera-
tures in the vehicle.

Never allow your child to be transported in a vehicle without the use of a
suitable restraint system.

Children should also never stand up in a vehicle or kneel on the seats when
the vehicle is moving. In the event of an accident the child will be thrown
through the vehicle and may as a result suffer fatal injuries, and also injure
other occupants.

Children are exposed to an increased risk of injury in the event of an acci-
dent if they lean forward or adopt an in correct seated position when the vehicle
is moving. This particularly applies to children who are transported on the front
s2rc.book Page 115 Thursday, April 22, 2010 10:58 AM